change time MAZDA MODEL CX-5 2017 Owners Manual (in English)

A Word to Mazda Owners
Thank you for choosing a Mazda. We at Mazda design and build vehicles with complete
customer satisfaction in mind.

To help ensure enjoyable and trouble-free operation of your Mazda, read t\
his manual
carefully and follow its recommendations.

An Authorized Mazda Dealer knows your vehicle best. So when maintenance or \
service is
necessary, that's the place to go.

Our nationwide network of Mazda professionals is dedicated to providing \
you with the best
possible service.

We assure you that all of us at Mazda have an ongoing interest in your mo\
toring pleasure
and in your full satisfaction with your Mazda product.
Mazda Motor Corporation HIROSHIMA, JAPAN


Important Notes About This Manual
Keep this manual in the glove compartment as a handy reference for the s\
afe and enjoyable use of your Mazda.
Should you resell the vehicle, leave this manual with it for the next ow\
ner.

All specifi cations and descriptions are accurate at the time of printing. Because i\
mprovement is a constant goal at
Mazda, we reserve the right to make changes in speci fi cations at any time without notice and without obligation.

Air-Conditioning and the Environment
Your Mazda's genuine air conditioner is fi lled with a refrigerant that has been found not to damage the earth's
ozone layer. If the air conditioner does not operate properly, consult an Authorized Mazda Dealer.
Perchlorate
Certain components of this vehicle such as [air bag modules, seat belt p\
retensioners, lithium batteries,…] may
contain Perchlorate Material-- Special handling may apply for service or\
vehicle end of life disposal. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.

Please be aware that this manual applies to all models, equipment and options. As a result, you may fi nd
some explanations for equipment not installed on your vehicle.


©2016 Mazda Motor Corporation Dec. 2016 (Print1)
CX-5_8FN1-EA-16L_Edition1.indb 32016/12/12 10:05:09

2–7
Essential Safety Equipment
Seats
*Some models.
Seat Warmer *
The front seats are electrically heated. The
ignition must be switched ON.
Press the seat warmer switch while the
ignition is switched ON to operate the seat
warmer. The indicator lights turn on to
indicate that the seat warmer is operating.
The mode changes as follows each time
the seat warmer switch is pressed.
OFF
High
Mid
Low

WARNING
Be careful when using the seat warmer: The heat from the seat warmer may be
too hot for some people, as indicated
as follows, and could cause a low-
temperature burn.
 Infants, small children, elderly people, and physically challenged
people
 People with delicate skin People who are excessively fatigued People who are intoxicated People who have taken sleep-inducing medicine such as sleeping
pills or cold medicine

Do not use the seat warmer with
anything having high moisture-
retention ability such as a blanket or
cushion on the seat: The seat may be heated excessively
and cause a low-temperature burn.

Do not use the seat warmer even when
taking a short nap in the vehicle: The seat may be heated excessively
and cause a low-temperature burn.

Do not place heavy objects with sharp
projections on the seat, or insert
needles or pins into it: This could cause the seat to become
excessively heated and result in injury
from a minor burn.

CX-5_8FN1-EA-16L_Edition1.indb 72016/12/12 10:05:15

2–9
Essential Safety Equipment
Seats
Programming
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P position.
3. Start the engine.
4. Adjust the seat and the active driving display to the desired driving position.
5. Press the SET button on the seat until a beep sound is heard one time.
6. Perform one of the following settings within 5 seconds of completing step 5
above:
 Programming using a button on
the side of the seat
 Press the button you want to program,
either button 1 or 2, until a beep
sound is heard one time.
 Programming using the key  Press the key button until a beep
sound is heard one time.

NOTE
If a beep sound is heard three times, the
operation is canceled.

To move the driving position to a
programmed position
(Using a button on the side of the seat)
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P position.
3. Start the engine.
4. Press the programming button for the driving position you want to call up
(button 1 or 2).
5. A beep sound is heard when the driving position adjustment is completed.

NOTE
  If the driving position movement is not
changed, only the beep sounds.
  A seat position can be called up even
with the engine not running.
  The driving position adjustment is
canceled in the following cases:
  Any of the seat adjustment switches
is operated.
  The SET button is pressed.  Programming button 1 or 2 is
pressed.
  The key button or button is
operated.
   The vehicle starts moving.  The active driving display is
adjusted.


(Using a programmed key)
1. Unlock the doors by pressing a request
switch or the key
button.
2. After unlocking the doors, the seat position adjustment begins within
40 seconds of opening the driver's door,
and a beep sounds when the operation
is fi nished.
3. Make sure the parking brake is on.
4. (Automatic transaxle)
Make sure the selector lever is in the P position.
5. Start the engine.
6. The active driving display adjustment begins.

CX-5_8FN1-EA-16L_Edition1.indb 92016/12/12 10:05:16

2–15
Essential Safety Equipment
Seats
*Some models.
Rear Seat Recline
WARNING
After adjusting the seatback, make
sure that it is fi rmly locked and the red
indication is not visible by attempting to
lightly move the seatback forward and
back: If the red indication is visible, the
seatback is not locked. If the vehicle
is driven with the seatback unlocked,
it may move unexpectedly and the
seating posture of the occupant
becomes unstable, resulting in an
accident.


Locked
position
Unlocked
position
Red indicator

CAUTION
When adjusting the seatback, always
support the seatback with your hand.
If the seatback is not supported by your
hand, it will move suddenly and could
cause injury.

NOTE
When you adjust the left seatback, the
center seatback moves at the same time.

The left and right seatbacks of the rear seat
can be adjusted separately.
Recline the seatback with the lever pulled
up.


Seat Warmer *
The rear seats are electrically heated. The
ignition must be switched ON.
Press the seat warmer switch while the
ignition is switched ON to operate the seat
warmer. The indicator lights turn on to
indicate that the seat warmer is operating.
The mode changes as follows each time
the seat warmer switch is pressed.
When using the seat warmer, fold the
armrest forward.
Refer to Armrest on page 2-17 .

OFF
High
Mid
Low

CX-5_8FN1-EA-16L_Edition1.indb 152016/12/12 10:05:17

3–5
Before Driving
Keys
Transmitter

Operation buttons
Operation indicator light

NOTE
 
 The headlights turn on/off by operating
the transmitter. Refer to Leaving Home
Light on page 4-55 .
  (With theft-deterrent system)  The hazard warning lights fl ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on page 3-47 .
  (With the advanced keyless function)  A beep sound can be heard for
confi rmation when the doors and the
liftgate are locked/unlocked using the
key. If you prefer, the beep sound can be
turned off.
 The volume of the beep sound can also be changed.
 Refer to Personalization Features on page 9-11 .

Use the following procedure to change the
setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
LOCK button on the key for
5 seconds or longer.
All of the doors and the liftgate lock and the beep sound activates at the
currently set volume. The setting
changes each time the LOCK button
on the key is pressed and the beep
sound activates at the set volume. (If
the beep sound has been set to not
activate, it will not activate.)
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
LOCK button on the key.
  Pressing a request switch.

The operation indicator light fl ashes when
the buttons are pressed.
CX-5_8FN1-EA-16L_Edition1.indb 52016/12/12 10:05:29

3–7
Before Driving
Keys
*Some models.
NOTE
  The system can be set to unlock all
doors by performing a single operation.
 Refer to Personalization Features on page 9-11 .
 Use the following procedure to change the setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
UNLOCK button on the key for
5 seconds or longer (the sound of
the doors locking/unlocking can be
heard).
After this, the system switches the setting each time the UNLOCK
button is pressed (the sound of the
doors locking/unlocking can be
heard).
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
UNLOCK button on the key.
  Pressing a request switch.
  (Auto re-lock function)  After unlocking with the key, all doors
and the liftgate will automatically lock
if any of the following operations are
not performed within about 60 seconds.
If your vehicle has a theft-deterrent
system, the hazard warning lights will
fl ash for confi rmation.
 The time required for the doors to lock
automatically can be changed.
 Refer to Personalization Features on page 9-11 .
  A door or the liftgate is opened.  The ignition is switched to any
position other than off.
  (With theft-deterrent system)  When the doors are unlocked by
pressing the unlock button on the key
while the theft-deterrent system is
turned off, the hazard warning lights
will fl ash twice to indicate that the
system is turned off.

Power liftgate button *
To open/close the liftgate, press the power
liftgate button for one second or more
with the liftgate in the fully closed/open
position.
The hazard warning lights fl ash twice and
the liftgate opens/closes after the beep
sounds.


CX-5_8FN1-EA-16L_Edition1.indb 72016/12/12 10:05:29

3–15
Before Driving
Doors and Locks
NOTE
  The system can be set to unlock all
doors by performing a single operation.
 Refer to Personalization Features on page 9-11 .
 Use the following procedure to change the setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
UNLOCK button on the key for
5 seconds or longer (the sound of
the doors locking/unlocking can be
heard).
After this, the system switches the setting of pressing the driver's
request switch once or twice to
unlock all doors and the liftgate
each time the UNLOCK button is
pressed (the sound of the doors
locking/unlocking can be heard).
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
UNLOCK button on the key.
  Pressing a request switch.   Confi rm that all doors and the liftgate
are securely locked.
 For the liftgate, move it without pressing the electric liftgate opener to
verify that the liftgate has not been left
ajar.
  All doors and the liftgate cannot be
locked when any door or the liftgate is
open.
  It may require a few seconds for the
doors to unlock after the request switch
is pressed.
  A beep sound is heard for confi rmation
when the doors and the liftgate are
locked/unlocked using the request
switch. If you prefer, the beep sound can
be turned off.
 The volume of the beep sound can also be changed. Refer to Personalization
Features on page 9-11 .
 Use the following procedure to change
the setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
LOCK button on the key for
5 seconds or longer.
All of the doors and the liftgate lock and the beep sound activates at the
currently set volume. The setting
changes each time the LOCK button
on the key is pressed and the beep
sound activates at the set volume. (If
the beep sound has been set to not
activate, it will not activate.)
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
LOCK button on the key.
  Pressing a request switch.
CX-5_8FN1-EA-16L_Edition1.indb 152016/12/12 10:05:30

3–16
Before Driving
Doors and Locks
  (With theft-deterrent system)  The hazard warning lights fl ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on page 3-47 .
  The setting can be changed so that
the doors and the liftgate are locked
automatically without pressing the
request switch.
 Refer to Personalization Features on page 9-11 .
 (Auto-lock function)  A beep sound is heard when all doors
and the liftgate are closed while the
advanced key is being carried. All doors
and the liftgate are locked automatically
after about three seconds when the
advanced key is out of the operational
range. Also, the hazard warning lights
fl ash once. (Even if the driver is in the
operational range, all doors and the
liftgate are locked automatically after
about 30 seconds.) If you are out of
the operational range before the doors
and the liftgate are completely closed
or another key is left in the vehicle, the
auto-lock function will not work. Always
make sure that all doors and the liftgate
are closed and locked before leaving the
vehicle. The auto-lock function does not
close the power windows.
   Auto re-lock function  After unlocking with the request
switch, all doors and the liftgate
will automatically lock if any of the
following operations are not performed
within about 60 seconds. If your
vehicle has a theft-deterrent system,
the hazard warning lights will fl ash for
confi rmation.
 The time required for the doors to lock
automatically can be changed.
 Refer to Personalization Features on page 9-11 .
  Opening a door or the liftgate.  Switching the ignition to any position
other than off.


Locking, Unlocking with Transmitter
All doors and the liftgate can be locked/
unlocked by operating the keyless entry
system transmitter, refer to Keyless Entry
System (page 3-3 ).
CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:05:30

3–19
Before Driving
Doors and Locks
Settings can be changed using the
following procedure.

1. Safely park the vehicle. All doors must remain closed.
2. Switch the ignition ON.
3. Press and hold the lock side of the driver's door-lock switch within
20 seconds of switching the ignition
ON, and make sure a beep sound is
heard about eight seconds afterwards.
4. Refer to the auto lock/unlock function setting table, determine the function
number for the desired setting. Press
the unlock side of the driver's door-lock
switch the same number of times as the
selected function number (Ex. If you
select function 2, press the unlock side
of the switch only 2 times).
5. Three seconds after the function setting has been changed, a beep sound will
beep in the amount of the selected
function number. (Ex. Function number
3 = 3 beep sounds)

(Manual transaxle vehicles)

Press 2 times
Press 3 times
Current Function Number
Function Number 1
Function Number 2
Function Number 3 Press 4 times
Press unlock side of
lock switch once
Cancel setting Cancel setting
Function set (The
number of beeps
heard is the same as
the selected function
number)
Press lock side of
lock switch
Wait for 3 second
(Automatic transaxle vehicles)


Press unlock side of
lock switch once
Press 2 times
Press 3 times
Current Function Number
Function Number 1
Function Number 2
Press 4 times
Function Number 3
Press 5 times
Function Number 4
Press 7 times
Function Number 5
Press 6 times
Function Number 6
Cancel setting Cancel setting
Function set (The
number of beeps
heard is the same as
the selected function
number)
Press lock side of
lock switch
Wait for 3 second

NOTE
   The doors cannot be locked or unlocked
while the setting function is being
performed.
  The procedure can be cancelled by
pressing the lock side of the driver's
door-lock switch.

CX-5_8FN1-EA-16L_Edition1.indb 192016/12/12 10:05:31

3–27
Before Driving
Doors and Locks
Operation from outside (To open)
Press the electric liftgate opener on the
liftgate and raise the liftgate. The hazard
warning lights fl ash twice and the liftgate
opens automatically after the beep sound
is heard.
(With the advanced keyless function)
A locked liftgate can also be opened while
the key is being carried.

Electric liftgate
opener

Operation from outside (To close)
Press the power liftgate close switch while
the liftgate is fully opened. The hazard
warning lights fl ash twice and the liftgate
closes automatically after the beep sound
is heard.

Power liftgate
close switch

NOTE
If the power liftgate switch/power liftgate
close switch is pressed or the electric
liftgate opener is operated while the
liftgate is opening/closing electrically, the
beep sound is heard and the liftgate stops.
Then, it reverses when any of the switches
are pressed again.

Changing the power liftgate fully open
position
The power liftgate fully-open position can
be changed according to the height of a
garage.
When changing the position
1. Stop the liftgate at the desired position.
2. Press the power liftgate close switch for about three seconds.
A beep sound is activated two times to indicate that the position change has
been completed.

NOTE
Set the desired fully-open position of the
liftgate at the position where it is open
more than halfway. The position where it
is less than halfway open cannot be set.

To reset
1. Open the liftgate.
2. Press the power liftgate close switch for about seven seconds.
A beep sound is activated three times to indicated that the reset has been
completed.

CX-5_8FN1-EA-16L_Edition1.indb 272016/12/12 10:05:33