MAZDA MODEL MPV 2005 Owners Manual (in English)

Black plate (291,1)
Without moonroof, with overhead
console
Edge
Without either moonroof or overhead
console
Edge
With moonroof
Edge
3. Install the new bulb in the reverse order
of removal.
Overhead light, Courtesy lights, Vanity
mirror lightsí
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
screwdriver.
2. Disconnect the bulb by pulling it out.
Overhead light
Edge
Courtesy lights
Edge
Maintenance and Care
Owner Maintenance
8-35íSome models. Mazda MPV_8T50-EA-04G_Edition1 Page291
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (292,1)
Vanity mirror lights
Edge
3. Install the new bulb in the reverse order
of removal.
Luggage compartment light
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the luggage
compartment light as shown in the
figure, and then remove the luggage
compartment light unit.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the driver's side
If the electrical system doesn't work, first
inspect fuses on the driver's side.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover.
8-36
Maintenance and Care
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page292
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (293,1)
3. Pull the fuse straight out with the fuse
puller provided on the fuse panel.
4. Inspect it and replace if it's blown.
NormalBlown
5. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an Authorized
Mazda Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components don't work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new
oneof the same amperage rating.
Normal
Blown
NOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer (page 8-38).
Maintenance and Care
Owner Maintenance
8-37
Mazda MPV_8T50-EA-04G_Edition1 Page293
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (294,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 DEFOG 40ARear window
defroster
2 BTN 60ASTOP,
HAZARD,
ROOM,
D.LOCK and
DRL fuses
3 ABS 60AAntilock brake
system
í, For
protection of
various circuits
4 FAN1 30A Cooling fan
5 FAN2 30A Cooling fan
6 HEATER 40A Heater
7 R.HEAT 30ARear heater
í,
For protection of
various circuitsDESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
8 IG KEY2 40AA/C, P.WIND
í,
MOONROOFí
and R.WIP fuses
9 A/C 10AAir conditioner,
For protection of
various circuits
10 TAIL 15A Taillights
11 AC PWR 15A Inverter
12 HORN 15A Horn
13 FOG 15AFor protection of
various circuits
14 EEC 5AFor protection of
various circuits
15 HEAD L 15A Headlight-left
16 HEAD R 15A Headlight-right
17 HID L 20A―
18 HID R 20A―
8-38
Maintenance and Care
íSome models.
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page294
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (295,1)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
19 IG KEY1 60AMETER,
ENGINE and
WIPER fuses
20 EGI INJ 30AFor protection of
various circuits
21 FUEL PUMP 20A Fuel pump
22 MAIN 120AFor protection of
all circuits
Maintenance and Care
Owner Maintenance
8-39
Mazda MPV_8T50-EA-04G_Edition1 Page295
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (296,1)
Fuse block (Driver's side)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 P.WIND 30APower
windows
í, For
protection of
various circuits
2 WIPER 20AWindshield
wipers and
washer
3 SUN ROOF 15A
Moonroofí, For protec-
tion of various circuits
4 R.WIP 10ARear window
wiper and washer
5 SEAT 20AFor protection of
various circuits
6 M.DEF 10AMirror
defroster
í, For
protection of
various circuits
7 A/C 10AAir conditioner,
For protection of
various circuitsDESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
8 DRL 10AFor protection of
various circuits
9―――
10 H/CLEAN 20AFor protection of
various circuits
11―――
12 HAZARD 10AHazard warning
flashers
13 ROOM 15AOverhead lights,
Map lights,
Luggage
compartment
light
14 AUX POWER 25A Accessory socket
15 CLOSER LH 20AFor protection of
various circuits
16 AUDIO 10AAudio system,
For protection of
various circuits
8-40
Maintenance and Care
íSome models.
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page296
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (297,1)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
17 D.LOCK 30APower door
locks
í, For
protection of
various circuits
18 P/SEAT 30A Power seat
í
19 ENGINE 10AEngine control
system
20 METER 10AInstrument
cluster
21 STOP 15A Brake lights
22 CLOSER RH 20AFor protection of
various circuits
23 ACC.DELAY 30APower windows
delay, For
protection of
various circuits
24 METER 15AInstrument
cluster, INH
switch
25 ST.SIGN 10A Starter signal
26 CIGAR 25A Lighter
27―――
28―――
Maintenance and Care
Owner Maintenance
8-41íSome models. Mazda MPV_8T50-EA-04G_Edition1 Page297
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (298,1)
How to Minimize
Environmental Paint
Damage
The paintwork on your Mazda represents
the latest technical developments in
composition and methods of application.
Environmental hazards, however, can
harm the paint's protective properties, if
proper care is not taken.
Here are some examples of possible
damage, with tips on how to prevent
them.
qEtching Caused by Acid Rain or
Industrial Fallout
Occurrence
Industrial pollutants and vehicle emissions
drift into the air and mix with rain or dew
to form acids. These acids can settle on a
vehicle's finish. As the water evaporates,
the acid becomes concentrated and can
damage the finish.
And the longer the acid remains on the
surface, the greater the chance is for
damage.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you suspect that acid rain has settled on
your vehicle's finish.
qDamage Caused by Bird
Dropping, Insects, or Tree Sap
Occurrence
Bird droppings contain acids. If these
aren't removed they can eat away the clear
and color base coat of the vehicle's
paintwork.
When insects stick to the paint surface
and decompose, corrosive compounds
form. These can erode the clear and color
base coat of the vehicle's paintwork if
they are not removed.
Tree sap will harden and adhere
permanently to the paint finish. If you
scratch the sap off while it is hard, some
vehicle paint could come off with it.
Prevention
It is necessary to have your Mazda
washed and waxed to preserve its finish
according to the instructions in this
section. This should be done as soon as
possible.
Bird droppings can be removed with a
soft sponge and water. If you are traveling
and these are not available, a moistened
tissue may also take care of the problem.
The cleaned area should be waxed
according to the instructions in this
section.
Insects and tree sap are best removed with
a soft sponge and water or a commercially
available chemical cleaner.
Another method is to cover the affected
area with dampened newspaper for one to
two hours. After removing the newspaper,
rinse off the loosened debris with water.
8-42
Maintenance and Care
Appearance Care
Mazda MPV_8T50-EA-04G_Edition1 Page298
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (299,1)
qWater Marks
Occurrence
Rain, fog, dew, and even tap water can
contain harmful minerals such as salt and
lime. If moisture containing these
minerals settles on the vehicle and
evaporates, the minerals will concentrate
and harden to form white rings. The rings
can damage your vehicle's finish.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you find water marks on your vehicle's
finish.
qPaint Chipping
Occurrence
Paint chipping occurs when gravel thrown
in the air by another vehicle's tires hits
your vehicle.
How to avoid paint chipping
Keeping a safe distance between you and
the vehicle ahead reduces the chances of
having your paint chipped by flying
gravel.
NOTE
lThe paint chipping zone varies with
the speed of the vehicle. For
example, when traveling at 90 km/h
(56 mph), the paint chipping zone is
50 m (164 ft).
lIn low temperatures a vehicle's finish
hardens. This increases the chance of
paint chipping.
lChipped paint can lead to rust
forming on your Mazda. Before this
happens, repair the damage by using
Mazda touch-up paint according to
the instructions in this section.
Failure to repair the affected area
could lead to serious rusting and
expensive repairs.
Maintenance and Care
Appearance Care
8-43
Mazda MPV_8T50-EA-04G_Edition1 Page299
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (300,1)
Exterior Care
Followalllabel and container directions
when using a chemical cleaner or polish.
Read all warnings and cautions.
qMaintaining the Finish
Washing
To help protect the finish from rust and
deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.
Scratches occur on the paint surface
when:
lThe vehicle is washed without first
rinsing off dirt and other foreign
matter.
lThe vehicle is washed with a rough,
dry, or dirty cloth.
lThe vehicle is washed at a car wash
that uses brushes that are dirty or too
stiff.
lCleansers or wax containing abrasives
are used.
NOTE
lMazda is not responsible for
scratches caused by automatic car
washes or improper washing.
lScratches are more noticeable on
vehicles with darker paint finishes.To minimize scratches on the vehicle's
paint finish:
lRinse off any dirt or other foreign
matter using lukewarm or cold water
before washing.
lUse plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
lRub gently when washing or drying the
vehicle.
lTake your vehicle only to a car wash
that keeps its brushes well maintained.
lDon't use abrasive cleansers or wax
that contain abrasives.
CAUTION
lDon't use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may damage
the protective coating; also, cleaners
and detergents may discolor or
deteriorate the paint.
lTo prevent damaging the antenna,
remove it before entering a car wash
facility or passing beneath a low
overhead clearance.
Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the fenders, and make
sure the drain holes in the lower edges of
the doors and rocker panels are clean.
8-44
Maintenance and Care
Appearance Care
Mazda MPV_8T50-EA-04G_Edition1 Page300
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G