power MAZDA MODEL MX-30 EV 2022 Owners Manual

Brake System
▼Foot Brake
This vehicle has power-assisted brakes
that adjust automatically through
normal use.

Should power-assist fail, you can stop
by applying greater force than normal
to the brake pedal. But the distance
required to stop will be greater than
usual.
WARNING
Do not coast with the EV system
stopped and stop the vehicle in a safe
place:
Coasting the vehicle with the EV
system stopped is dangerous. Braking
will require more
eff ort, and the
brake's power-assist could be
depleted if you pump the brake. This
will cause longer stopping distances or
even an accident.
Shift to a lower gear when going
down steep hills:
Driving with your foot continuously on
the brake pedal or steadily applying
the brakes for long distances is
dangerous. This causes overheated
brakes, resulting in longer stopping
distances or even total brake failure.
This could cause loss of vehicle control
and a serious accident. Avoid
continuous application of the brakes.
Dry off brakes that have become wet
by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the
brake performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
a ff ected.
CAUTION
 Do not drive with your foot held on
the brake pedal. Doing so could
result in the following:
 The brake parts will wear out more
quickly.
 The brakes can overheat and
adversely
aff ect brake
performance.
 Always depress the brake pedal with
the right foot. Applying the brakes
with the unaccustomed left foot
could slow your reaction time to an
emergency situation resulting in
insu fficient braking operation.
 Wear shoes appropriate for driving in
order to avoid your shoe contacting
the brake pedal when depressing the
accelerator pedal.
▼ Electric Parking Brake (EPB)
The EPB system applies the parking
brake using an electric motor. The
system can operate automatically and
manually.
The EPB switch indicator light turns on
when applying the parking brake and it
When Driving
Brake
4-52
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

turns off when releasing the parking
brake.
1. Indicator light
WARNING
Do not drive the vehicle with the
parking brake applied:
If the vehicle is driven with the parking
brake applied, the brake parts may
generate heat and the brake system
may not operate, leading to an
accident.
Before driving the vehicle, release the
parking brake and make sure that the
EPB indicator light in the instrument
cluster turns o ff.
Apply the parking brake when leaving
the vehicle:
Not applying the parking brake when
parking the vehicle is dangerous as the
vehicle may move unexpectedly and
result in an accident. Before leaving the
vehicle, apply the parking brake and
make sure that the EPB indicator light
in the instrument cluster turns on.
NOTE
The parking brake cannot be applied
or released while the vehicle battery
is dead.
Refer to Jump-Starting on page
7-12.
When the power switch is switched
OFF while the charging system
warning light in the instrument
cluster turns on, the parking brake
cannot be applied. Before switching
the power switch OFF, apply the
parking brake manually.
The sound of the parking brake being
applied or released can be heard,
however, this does not indicate a
problem.
If the EPB is no t used for long
periods, an automatic inspection of
the system is performed while the
vehicle is parked. An operation
sound can be heard, however, this
does not indicate a problem.
When applying the parking brake
and switching the power switch OFF,
an operation sound can be heard,
however, this does not indicate a
problem.
The brake pedal may move while
applying or releasing the parking
brake, however, this does not
indicate a problem.
If there is a problem with the brake
system (foot brake) while driving the
vehicle, continually pulling up the
EPB switch will apply the brakes and
decelerate or stop the vehicle. The
parking brake on-reminder sound is
activated while the brake is applied.
In addition, when releasing the
switch, the brake is released and the
sound stops.
If the parking brake is applied with
the power switch switched OFF or in
ACC, the EPB indicator light in the
instrument cluster and the indicator
light in the EPB switch may flash for
15 seconds.
When Driving
Brake
4-53
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

When using an automatic car wash
which moves the vehicle with the
front tires mounted, it is necessary to
cancel the parking brake auto
operation before the vehicle enters
the automatic car wash. For details,
refer to Canceling the parking brake
automatic operation.
Release the parking brake and use
neutral hold mode (automatic car
wash mode) when it is necessary to
change the shift position to the N
position for an automatic car wash.
Refer to Selector Lever Operation on
page 4-28.
Manual operation
Applying the parking brake manually
When the brake pedal is firmly
depressed and the EPB switch is pulled
up, the parking brake is applied
regardless of the power switch
position. When the parking brake is
applied, the EPB indicator light in the
instrument cluster and the EPB switch
indicator light turn on.
Releasing the parking brake manually
When the parking brake is firmly
depressed and the EPB switch is
pressed with the power switch
switched ON, the parking brake is
released. When the parking brake is
released, the EPB indicator light in the
instrument cluster and the EPB switch
indicator light turn off .
If the EPB switch is pressed without
depressing the brake pedal, a message
is displayed on the multi-information
display to notify the driver to depress
the brake pedal.
Refer to Message Indicated on
Multi-information Display on page
7-33.
Auto operation
Applying the parking brake
automatically
When the power switch is switched
from ON to ACC or OFF, the parking
brake will be applied automatically.
When the parking brake is applied, the
EPB indicator light in the instrument
cluster and the EPB switch indicator
light turn on.
NOTE
To release the parking brake when
the power switch is switched OFF, it
is necessary to cancel the parking
brake auto operation. For details,
refer to Canceling the parking brake
automatic operation.
When the power switch is switched
from ON to ACC while in neutral
hold mode (automatic car wash
mode), the parking brake is applied
automatically.
When Driving
Brake
4-54
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Releasing the parking brake
automatically
If the accelerator pedal is depressed
with the parking brake applied and all
of the following conditions met, the
parking brake is released automatically.
When the parking brake is released,
the EPB indicator light in the
instrument cluster and the EPB switch
indicator light turn off.
The power switch is switched ON
(EV system on).
The driver's door is closed.The driver's seat belt is fastened.The selector lever is in the D or R
position.
NOTE
If something such as the driver’s foot
contacts the accelerator pedal with the
power switch switched ON (EV system
on) and the parking brake applied, the
parking brake might be released
automatically. If you do not intend to
start driving the vehicle immediately,
shift the selector lever to the P or N
position.
Canceling the parking brake
automatic operation
The parking brake automatic operation
can be canceled by doing any of the
following after switching the power
switch from ON to OFF.
Auto operation cancel method 1
1. Switch the power switch ON.
2. Release the parking brake manually.
3. Turn
off the AUTOHOLD.
4. Press the EPB switch continuously for 2 seconds or longer (until a
sound is activated).
5. Release the EPB switch and switch the power switch OFF within 5
seconds after the sound was
activated.
After the auto operation is
canceled, a sound is activated one
time, and the EPB switch indicator
light switches from illumination to
flashing , and then turns o ff after 3
seconds.
Auto operation cancel method 2
1. Switch the power switch ON.
2. Release the parking brake manually.
3. Turn o ff the AUTOHOLD.
4. Switch the power switch OFF with the EPB switch pressed while the
brake pedal is not depressed.
When the auto operation is
canceled, a sound is activated one
time, and the EPB switch indicator
light goes from normal flashing to
faster flashing , and then turns o ff
after 3 seconds.
NOTE
When canceling the parking brake
auto operation and parking the
vehicle, shift the selector lever to the
P position and then use wheel
blocks.
The auto operation may not cancel if
the vehicle is parked on a steep
slope.
When the power switch is switched
ON, the parking brake auto operation
is restored.
▼ Warning Light
The warning light turns on when the
system has a malfunction.
Refer to Brake System Warning
Indication/Warning Light on page
7-21.
When Driving
Brake
4-55
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

CAUTION
If you stop operating the accelerator pedal before the vehicle starts moving, the
force holding the vehicle in the stopped position may weaken. Firmly depress the
brake pedal or depress the accelerato r pedal to accelerate the vehicle.
NOTE
Under the following conditions, a problem with the AUTOHOLD is occurring.
Have your vehicle inspected at an Authorized Mazda Dealer as soon as possible.
A message is indicated on the multi-information display and a warning sound is
activated for about 5 seconds while the AUTOHOLD is operating or when you
press the AUTOHOLD switch.
If you switch the power switch OFF while the AUTOHOLD is operating, the
parking brake is applied automatically to assist you with parking the vehicle.
The AUTOHOLD is canceled when the selector lever is shifted to R position while
the vehicle is on level ground, or facing up a hill or grade (as shown below).
Vehicle posture and road surface gradient AUTOHOLD operation status
Ve h i c l e t i l t s f o r wa r d
Operates
Level ground
Does not operate, canceled
Ve h i c l e t i l t s rea r wa rd
Does not operate, canceled
: Reverse driving (selector lever in the reverse (R) position)
When Driving
Brake
4-58
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

The brake pedal response may change, sound may occur from the brakes, or the
brake pedal could vibrate from the operation of the AUTOHOLD function.
However, this does not indicate a malfunction.
▼To Turn On AUTOHOLD System
Press the AUTOHOLD switch and
when the AUTOHOLD standby
indicator light turns on, the
AUTOHOLD function turns on.
1. AUTOHOLD standby indicator light
NOTE
When all of the following conditions
are met, the AUTOHOLD standby
indicator light turns on when the
AUTOHOLD switch is pressed and the
AUTOHOLD function turns on.
The power switch is switched ON
(EV system on).
The driver's seat belt is fastened.The driver's door is closed.There is no problem with the
AUTOHOLD function.
To operate AUTOHOLD and hold the
brakes
1. Depress the brake pedal and bring the vehicle to a complete stop.
2. The AUTOHOLD active indicatorlight in the instrument cluster turns
on and the brakes are held.
3. The vehicle is held in its stoppedposition even with the brake pedal
released.
NOTE
When all of the following conditions
are met, the AUTOHOLD operates and
the brakes are held.
The power switch is switched ON
(EV system on).
The vehicle is stopped.The brake pedal is being depressed.The AUTOHOLD active indicator
light turns on.
The accelerator pedal is not
depressed.
The driver's seat belt is fastened.The driver's door is closed.There is no problem with the
AUTOHOLD function.
The parking brake is released.There is no problem with the Electric
Parking Brake (EPB) function.
The selector lever is in a position
other than R position or the vehicle
tilts forward with the selector lever in
the R position.
To release AUTOHOLD and start
driving the vehicle
If you try to resume driving the vehicle,
the brakes will be released
automatically and the AUTOHOLD
active indicator light turns o ff.
When Driving
Brake
4-59
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

NOTE
If the Electric Parking Brake (EPB)
switch is pulled while the
AUTOHOLD is operating, the
parking brake is applied and the
AUTOHOLD is released. In addition,
if the parking brake is released under
this condition, the AUTOHOLD
operates to hold the brakes.
Under the following conditions, the
parking brake is automatically
applied and the AUTOHOLD is
released. The AUTOHOLD is
re-enabled when the conditions
before the AUTOHOLD is released
are restored.
The driver’s seat belt is unfastened.The driver’s door is opened.When about 10 minutes or longer
have passed since the AUTOHOLD
operation started, the parking brake
is automatically applied. Because the
AUTOHOLD is restored when
releasing the parking brake, the hold
on the brakes by AUTOHOLD
function resumes.
The AUTOHOLD can be canceled
forcibly by fully depressing the
accelerator pedal for 1 second or
longer while the AUTOHOLD is
operating. Forcibly cancel the
AUTOHOLD only when the
AUTOHOLD cannot be canceled due
to a system malfunction or it is
necessary to cancel the AUTOHOLD
in an emergency.
▼To Tu r n
Off AUTOHOLD System
Depress the brake pedal and press the
AUTOHOLD switch. The AUTOHOLD
is turned o
ff and the AUTOHOLD
standby indicator light turns o ff.
1. AUTOHOLD standby indicator light
NOTE
When the brakes are not held such
as while driving the vehicle, the
AUTOHOLD can be turned o ff only
by pressing the AUTOHOLD switch.
If the AUTOHOLD switch is pressed
without depressing the brake pedal
while AUTOHOLD is operating
(AUTOHOLD active indicator light in
instrument cluster is turned on), the
message “Depress Brake Pedal and
Operate Switch to Release” is
indicated on the multi-information
display to notify the driver to depress
the brake pedal.
If any of the following conditions
occurs while the AUTOHOLD
function is operating (AUTOHOLD
active indicator light is turned on),
the parking brake is applied
automatically and the AUTOHOLD
function turns o ff. For the Electric
Parking Brake (EPB) operation, refer
to the Electric Parking Brake (EPB) on
page 4-52.
The power switch is switched OFF.There is a problem with the
AUTOHOLD function.
When Driving
Brake
4-60
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Tra c t i o n C o n t r o l Sy s te m(TCS)
▼Traction Control System (TCS)
The Traction Control System (TCS)
prevents drive-wheel spinning which
occurs during acceleration from a stop
or acceleration during cornering on
slippery roads, such as wet or
snow-covered roads, and assures
optimum drive force and steerability.


The warning light turns on when the
system has a malfunction.
Refer to TCS/DSC Indication/
Indicator Light (Turns on) on page
7-27.
WARNING
Do not rely on the Traction Control
System (TCS) as a substitute for safe
driving:
The Traction Control System (TCS)
cannot compensate for unsafe and
reckless driving , excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning
(reduced tire friction and road contact
because of water on the road surface).
You can still have an accident.
Use snow tires or tire chains and drive
at reduced speeds when roads are
covered with ice and/or snow:
Driving without proper traction devices
on snow and/or ice-covered roads is
dangerous. The Traction Control
System (TCS) alone cannot provide
adequate traction and you could still
have an accident.
NOTE
To t u r n o
ff the TCS, press the TCS OFF
switch (page 4-65).
▼ TCS/DSC Indicator Light
When the power switch is switched
ON, the TCS/DSC indicator light turns
on and then turns
off after a few
seconds.
If the TCS or DSC is operating, the
indicator light flashes.

If the light stays on, the TCS, DSC or
the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an
Authorized Mazda Dealer.
NOTE
When the TCS/DSC operation
indicator light fl ashes, a sound from
the motor compartment may be
heard, however, this does not
indicate a problem. This indicates
that the TCS/DSC is operating
normally.
On slippery road surfaces, such as
freshly fallen snow, the motor
rotation speed cannot be increased
when the TCS is on.
▼ TCS OFF Indicator Light
This indicator light stays on for a few
seconds when the power switch is
switched ON.
When Driving
ABS/TCS/DSC
4-64
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

It also illuminates when the TCS OFF
switch is pressed and TCS is switched
off.
Refer to TCS OFF Switch on page
4-65.

If the light remains illuminated and the
TCS is not switched o ff, take your
vehicle to an Authorized Mazda
Dealer. The DSC may have a
malfunction.
▼ TCS OFF Switch
Press the TCS OFF switch to turn o
ff the
TCS. The TCS OFF indicator light in the
instrument cluster will illuminate.

Press the switch again to turn the TCS
back on. The TCS OFF indicator light
*
will turn o ff.
NOTE
When the TCS is on and you attempt
to free the vehicle from being stuck,
or drive it out of freshly fallen snow,
the TCS will activate. Depressing the
accelerator pedal will not increase
motor power and freeing the vehicle
might be di fficult. When this
happens, turn o ff the TCS.
If the EV system is turned o ff with the
TCS turned off, the TCS becomes
operational when the EV system is
started the next time.
Leaving the TCS on will provide the
best traction.
If the TCS OFF switch is pressed and
held for 10 seconds or more, the
TCS OFF switch malfunction
detection function operates and the
TCS system activates automatically.
The TCS OFF indicator light turns o ff
while the TCS system is operative.
When Driving
ABS/TCS/DSC
*Some models.4-65
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Dynamic Stability Control(DSC)
▼Dynamic Stability Control (DSC)
The Dynamic Stability Control (DSC)
automatically controls braking and
motor torque in conjunction with
systems such as the ABS and TCS to
help control side slip when driving on
slippery surfaces, or during sudden or
evasive steering, which enhances
vehicle stability.

Refer to ABS (page 4-63) and TCS
(page 4-64).

DSC operation is possible at speeds
greater than 20 km/h (12 mph).

The warning light turns on when the
system has a malfunction.
Refer to TCS/DSC Indication/
Indicator Light (Turns on) on page
7-27.
WARNING
Do not rely on the Dynamic Stability
Control as a substitute for safe
driving:
The Dynamic Stability Control (DSC)
cannot compensate for unsafe and
reckless driving , excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning
(reduced tire friction and road contact
because of water on the road surface).
You can still have an accident.
CAUTION

The DSC may not operate correctly
unless the following are observed:
 Use tires of the correct size
speci fied for your Mazda on all 4
wheels.
 Use tires of the same
manufacturer, brand and tread
pattern on all 4 wheels.
 Do not mix worn tires.
 The DSC may not operate correctly
when tire chains are used or a
temporary spare tire is installed
because the tire diameter changes.
NOTE
If there is a problem with the DSC, the
Hill Launch Assi st (HLA) may not
operate.
Refer to Hill Launch Assist (HLA) on
page 4-61.
▼ TCS/DSC Indicator Light
When the power switch is switched
ON, the TCS/DSC indicator light turns
on and then turns
off after a few
seconds. If the TCS or DSC is
operating , the indicator light flashes.

If the light stays on, the TCS, DSC or
the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an
Authorized Mazda Dealer.
When Driving
ABS/TCS/DSC
4-66
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07