brake MAZDA MODEL MX-5 MIATA 2002 Owner's Guide

7-6
In Case of an Emergency
Flat Tire
Form No. 8Q42-EA-01F
1. Park on a level surface off the right-of-way and firmly set the parking brake.
2. Put a vehicle with an automatic transmission in park (P), a manual
transmission in reverse (R), and turn
off the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle and away from the vehicle and traffic.
5. Remove the jack, tool, and spare tire (page 7-3).
6. Block the wheel diagonally opposite the flat tire. When blocking a front
wheel, place the block in front of the
tire. When blocking a rear wheel, place
the block behind the tire.

Removing a Flat Tire
1. Loosen the lug nuts by turning them
counterclockwise one turn each, but
don ’t remove any until the tire has been
raised off the ground.
2. Place the jack under the jacking position closest to the tire being
changed.
NOTE
Make sure the jack is well lubricated
before using it.
Jacking position
J07L(02MY).book Page 6 Monday, June 11, 2001 4:52 PM

7-11
In Case of an Emergency
Form No. 8Q42-EA-01F
Overheating
If the temperature gauge indicates
overheating, you experience power loss,
or you hear a loud knocking or pinging
noise, the engine is probably too hot.
If this happens:
1. Drive safely to the side of the road and park off the right-of-way.
2. Put a vehicle with an automatic transmission in park (P), a manual
transmission in neutral.
Apply the parking brake.
3. Turn off the air conditioner. 4. Check whether coolant or steam is
escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment, don ’t go near the front
of the vehicle. Stop the engine. Then
turn the ignition switch to the ON
position without starting the engine.
The radiator cooling fans will start to
cool the engine.
If neither coolant nor steam is
escaping, open the hood and idle the
engine until it cools. If this doesn ’t
lower the temperature, stop the engine
and let it cool.
5. Visually inspect the alternator/water pump drive belt for looseness and
breakage and all cooling hose
connections for leaks. If the belt is
broken or coolant is leaking, call an
Authorized Mazda Dealer for
assistance.
6. If the drive belt is OK, the engine is cool, and no coolant leaks are obvious,
inspect the coolant level. Carefully add
coolant as required (page 8-15).
Overheating
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
WARNING
Cooling system cap
Engine coolant
reservoir
J07L(02MY).book Page 11 Monday, June 11, 2001 4:52 PM

8-1
Form No. 8Q42-EA-01F
8Maintenance and Care
How to keep your Mazda in top condition.
Introduction ................................................................................. 8- 2
Introduction ............................................................................. 8- 2
Scheduled Maintenance .............................................................. 8- 3
Scheduled Maintenance (North America) ............................... 8- 3
Scheduled Maintenance (Except North America) ................... 8- 7
Owner Maintenance .................................................................... 8-10
Owner Maintenance Schedule ................................................. 8-10
Owner Maintenance Precautions ............................................. 8-11
Engine Compartment Overview .............................................. 8-12
Engine Oil ................................................................................ 8-13
Engine Coolant ........................................................................ 8-15
Brake Fluid .............................................................................. 8-17
Clutch Fluid ............................................................................. 8-18
Power Steering Fluid ............................................................... 8-19
Automatic Transmission Fluid (ATF) ...................................... 8-20
Washer Fluid ............................................................................ 8-22
Body Lubrication ..................................................................... 8-23
Air Filter .................................................................................. 8-23
Wiper Blades ........................................................................... 8-24
Battery ..................................................................................... 8-26
Tires ......................................................................................... 8-27
Light Bulbs .............................................................................. 8-31
Fuses ........................................................................................ 8-37
Appearance Care ......................................................................... 8-41
How to Minimize Environmental Paint Damage ..................... 8-41
Exterior Care ........................................................................... 8-43
Interior Care ............................................................................ 8-48
J07L(02MY).book Page 1 Monday, June 11, 2001 4:52 PM

8-3
Maintenance and Care
Form No. 8Q42-EA-01F
Scheduled Maintenance
Follow Schedule 1 if the vehicle is operated mainly where none of the following conditions
apply.
If any do apply, follow Schedule 2 (Canada and Puerto Rico residents follow Schedule 2).
•Repeated short-distance driving
• Driving in dusty conditions
• Driving with extended use of brakes
• Driving in areas where salt or other corrosive materials are being used
• Driving on rough or muddy roads
• Extended periods of idling or low-speed operation
• Driving for long periods in cold temperatures or extremely humid climates
Scheduled Maintenance (North America)
NOTE
After the described period, continue to follow the described maintenance at the
recommended intervals.
J07L(02MY).book Page 3 Monday, June 11, 2001 4:52 PM

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8Q42-EA-01F

Schedule 1
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R: Replace
L : Lubricate
*: According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance
services be performed at the recommended time or kilometrage (mileage) period to ensure long-term
reliability.
Maintenance Interval
Maintenance
Item Number of months or kilometers (miles), whichever comes first 6 12182430364248
× 1000 Km 12 24 36 48 60 72 84 96
(× 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60)
Engine valve clearance I
Engine timing belt Replace every 96,000km (60,000miles)
Drive belt (tension) II
Engine oil RRRRRRRR
Engine oil filter RRRRRRRR
Cooling system II
Engine coolant Replace at first 72,000km (45,000miles) or 36 months ;
after that, every 48,000km (30,000miles) or 24 months
Idle speed II
Air filter RR
Fuel lines and hoses
*II
Hoses and tubes for emission
*I
Spark plugs RR
Brake lines, hoses and connections II
Disc brakes II
Steering operation and linkages II
Manual transmission oil R
Rear differential oil R
Front suspension ball joints II
Driveshaft dust boots II
Bolts and nuts on chassis and body II
Exhaust system heat shields II
All locks and hinges LLLLLLLL
Refrigerant amount (if installed) IIII
Compressor operation (if installed) IIII
J07L(02MY).book Page 4 Monday, June 11, 2001 4:52 PM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8Q42-EA-01F

Schedule 2
I
: Inspect: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R: Replace
L :Lubricate
*: According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance
services be performed at the recommended time or kilometrage (mileage) period to ensure long-term
reliability.
Maintenance Interval
Maintenance
Item Number of months or kilometers (miles), whichever comes first
Months 4 8 12 16 20 24 28 32 36 40 44 48
× 1000 Km 8 1624324048566472808896
(× 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60)
Engine valve clearance I
Engine timing belt Replace every 96,000km (60,000miles)
Drive belts (tension) II
Engine oil Puerto Rico Replace every 5,000km (3,000miles) or 3 months
others RRRRRRRRRRRR
Engine oil filter RRRRRRRRRRRR
Cooling system II
Engine coolant Replace at first 72,000km (45,000miles) or 36 months ;
after that, every 48,000km (30,000miles) or 24 months
Engine coolant level IIIIIIIIIIII
Idle speed II
Air filter I
*R
I *R
Fuel lines and hoses*II
Hoses and tubes for emission*I
Spark plugs RR
Function of all lights IIIIIIIIIIII
Brake lines, hoses and connections II
Brake and clutch fluid level IIIIIIIIIIII
Disc brakes IIII
Tire inflation pressure and tire wear IIIIIIIIIIII
Steering operation and linkages II
Power steering fluid level IIIIIIIIIIII
Manual transmission oil RR
Rear differential oil RR
Front suspension ball joints II
Driveshaft dust boots II
Bolts and nuts on chassis and body IIII
Exhaust system heat shields II
All locks and hinges LLLLLLLLLLLL
Washer fluid level IIIIIIIIIIII
J07L(02MY).book Page 5 Monday, June 11, 2001 4:52 PM

8-8
Maintenance and Care
Scheduled Maintenance
Form No. 8Q42-EA-01F
I: Inspect: Inspect and clean, repair, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R : Replace
T: Tighten
L : Lubricate
*1: Also inspect and adjust the power steering and air conditioner drive belts, if installed.
*2: Replacement of the timing belt is required at every 100,000 km {60,000 miles}. Failure to replace the timing belt may result in damage to the engine.
*3: If the vehicle is operated under any of the following conditions, change the engine oil and oil filter more often than recommended intervals.
a) Driving in dusty conditions.
b) Extended periods of idling or low speed operation.
c) Driving for long period in cold temperatures or driving regularly at short distance only.
*4: If the vehicle is operated in very dusty or sandy areas, inspect and if necessary, clean or replace the air filter more often than the recommended intervals.
*5: If the brakes are used extensively (for example, continuous hard driving or mountain driving)
or if the vehicle is operated in extremely humid climates, change the brake fluid annually.
*6: This is a full function check of electrical systems such as lights, wiper and washer systems (including wiper blades), and power windows.
Maintenance
Interval
Maintenance
Item Number of months or kilometers (miles), whichever comes first
Months 6 121824 30 36 42485460667278849096
× 1000 Km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
(× 1000 Miles) (6) (12) (18) (24) (30) (36) (42) (48) (54) (60) (66) (72) (78) (84) (90) (96)
Engine valve clearance Inspect every 100,000 km (60,000 miles) or 60 months
Drive belts
*1IIII I I IIIIIIIIII
Engine timing belt*2Replace every 100,000 km (60,000 miles)
Engine oil*3RRRR R R RRRRRRRRRR
Engine oil filter*3RRRR R R RRRRRRRRRR
Cooling system II I IIIII
Engine coolant Replace every 2 years
Idle speed II I IIIII
Air filter
*4IR I RIRIR
Fuel filter R RRR
Fuel lines and hoses II I IIIII
Spark plugs R R RRR
Evaporative system II I IIIII
E.G.R. system II I IIIII
All electrical system
*6 II I IIIII
Head light alignment I I III
Brake pedals and clutch pedals IIII I I IIIIIIIIII
Brake lines, hoses and
connections II I IIIII
Clutch fluid IIII I I IIIIIIIIII
Brake fluid
*5I I IR I I IRI I IRI I IR
Parking brake IIII I I IIIIIIIIII
Power brake unit and hoses II I IIIII
Disc brakes IIII I I IIIIIIIIII
J07L(02MY).book Page 8 Monday, June 11, 2001 4:52 PM

8-10
Maintenance and Care
Form No. 8Q42-EA-01F
Owner Maintenance
The owner or a qualified service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.
Bring any problem to the attention of an Authorized Mazda Dealer or qualified service
technician as soon as possible.

When Refueling
• Brake and clutch fluid level (page 8-17)
• Engine coolant level (page 8-15)
• Engine oil level (page 8-13)
• Washer fluid level (page 8-22)


At Least Monthly
• Tire inflation pressures (page 8-28)


At Least Twice a Year (For Example, Every Spring and Fall)
• Automatic transmission fluid level (page 8-20)
• Power steering fluid level (page 8-19)
You can do the following scheduled maintenance items if you have some mechanical
ability and a few basic tools and if you closely follow the directions in this manual.
• Air filter (page 8-23)
• Engine coolant (page 8-15)
• Engine oil (page 8-14)
Owner Maintenance Schedule
J07L(02MY).book Page 10 Monday, June 11, 2001 4:52 PM

8-12
Maintenance and Care
Owner Maintenance
Form No. 8Q42-EA-01F
Engine Compartment Overview
Fuse blockEngine oil-filler cap Cooling system cap Power steering fluid filler cap/dipstick Air filterClutch fluid reservoir
(Only for manual
transmission model)
Automatic transmission fluid-level dipstick
(Only for automatic transmission model)
Engine oil dipstickBrake fluid reservoir
Washer fluid reservoir
(TypeA)
The battery is in the trunk
ngine coolant
eservoir Washer fluid reservoir (TypeB)
J07L(02MY).book Page 12 Monday, June 11, 2001 4:52 PM

8-17
Maintenance and Care
Owner Maintenance
Form No. 8Q42-EA-01F
1. Remove the cooling system cap.
2. Only when the engine is cool, remove the radiator drain plug and drain the
coolant into a suitable container.
3. Flush out the system with running water.
4. Drain the system completely. Insert and tighten the plug. Add as much
ethylene-glycol-based coolant and
water as necessary to provide freezing
and corrosion protection.
5. In extremely cold climates, add the amount recommended in the coolant
manufacturer ’s instructions.
6. Run the engine at idle with the cooling system cap off. Slowly add additional
coolant if necessary.
7. At this point, wait until the engine reaches normal operating temperature;
then depress the accelerator two or
three times. Add more coolant, if
necessary, until the system is full.
8. Install the cooling system cap. Inspect all connections for leaks. Inspect the
level in the coolant reservoir one more
time.

Inspecting Brake Fluid Level
Inspect the fluid level in the reservoir
regularly. It should be kept at MAX.
The level normally drops with
accumulated distance, a condition
associated with wear of brake linings. If it
is excessively low, have the brake system
inspected by an Authorized Mazda
Dealer.
Tighten
Loosen
Tighten Loosen
Brake Fluid
J07L(02MY).book Page 17 Monday, June 11, 2001 4:52 PM