MAZDA MODEL PROTÉGÉ 2002 (in English) Manual PDF

3-15
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F
The ignition switch must be in the ON
position for the power windows to operate.

Operating the Driver’s Side
Power Window
To open the window, push down the
switch.
To close the window, pull up the switch.Auto-opening
To fully open the window automatically,
push the switch completely down.
To stop the window partway, pull up the
switch and then release it.

Operating the Passenger Power
Windows
The power windows may be operated
when the power window lock switch is in
the unlock position.
The passenger windows may be opened or
closed by the power window master
control switches on the driver’s door.
Power Windows
Closing Power Windows:
Closing power windows are
dangerous. A person’s hands, head,
or even neck could be caught by the
window and result in serious injury or
even death.
This warning applies especially to
children. Make sure the opening is
clear before closing a window.
To prevent burning out the fuse and
damaging the power window system,
don’t open or close more than two
windows at once.
WARNING
CAUTION
Close
OpenLeft front window
Right front window
Left rear window
Right rear window
J39L(02MY).book Page 15 Thursday, November 1, 2001 10:49 AM

3-16
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F
Front passenger-side power window
To open the window, push down the
switch.
To close the window, pull up the switch.
Rear power windows
To open a window, push the lower part of
the switch.
To close, push the upper part of the
switch.

Power Window Lock Switch
With the lock switch in the unlocked
position, all power windows on each door
can be operated.
With the lock switch in the locked
position, only the driver’s door power
window can be operated.
OpenClose
Open
Close
Unintentional Window Operation:
Unintentional window operation is
dangerous. A person’s hands, head,
or neck could be caught by the
window and result in serious injury.
Unless a passenger needs to operate a
window, keep the power window lock
switch in the locked position.
Unlocked positionLocked position
WARNING
J39L(02MY).book Page 16 Thursday, November 1, 2001 10:49 AM

3-17
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F

Fuel-Filler Lid
To open, pull up the remote fuel-filler lid
release.
Fuel-Filler Lid and Cap
Fuel Spray:
Fuel spray is dangerous. Fuel can
burn skin and eyes and cause illness
when ingested. Fuel spray is released
when there is pressure in the fuel
tank and the fuel cap is removed too
quickly. When removing the fuel cap,
loosen the cap slightly and wait for
any hissing to stop. Then remove it.
Fuel Vapor:
Fuel vapor is dangerous. It could be
ignited by sparks or flames causing
serious burns and injuries. Before
refueling, stop the engine,
and always
keep sparks and flames away from the
filler neck.
Always use only a genuine Mazda fuel
cap or an approved equivalent,
available at Authorized Mazda
Dealers. The wrong cap can result in a
serious malfunction of the fuel and
emission control systems. It may also
cause the check engine light in the
instrument cluster to illuminate.
WARNING
CAUTION
Remote fuel-filler
lid relese
Sedan
Remote fuel-filler
lid relese
Hatchback
J39L(02MY).book Page 17 Thursday, November 1, 2001 10:49 AM

3-18
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F

Fuel-Filler Cap
To remove the filler cap, turn it
counterclockwise.
To replace the filler cap, turn it clockwise
until it clicks.

Opening the Hood
1. With the vehicle parked, pull the
release handle to unlock the hood.
2. Pull the safety catch up and lift the
hood.
Make sure the fuel-filler cap is
tightened securely. The check engine
light comes on when the cap isn’t
tightened securely. If the light remains
on (even after you have tightened the
cap securely, driven, and restarted the
engine several times), it may indicate a
different problem. Contact an
Authorized Mazda Dealer as soon as
possible.
Open
Close
CAUTION
Hood
J39L(02MY).book Page 18 Thursday, November 1, 2001 10:49 AM

3-19
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F
3. Use the support rod to hold the hood
open.
Before closing the hood, secure the rod in
its clip.

Closing the Hood
1. Check under the hood area to make
certain all filler caps are in place and
all loose items (e.g. tools, oil
containers, etc.) have been removed.
2. Close the hood so that it locks securely.The sunroof can be opened or closed
electrically only when the ignition switch
is in the ON position.
Clip
Support rod
Sunroof
Extending the Head or Arms
Through the Sunroof:
Extending the head, arms, or other
parts of the body through the sunroof
is dangerous. The head or arms could
hit something while the vehicle is
moving. This could cause death or
serious injury. Don’t let passengers
stand up or extend anything through
the open sunroof while the vehicle is
moving.
Closing the Sunroof:
A closing sunroof is dangerous. The
hands, head, or even neck of a person
—especially a child— could be
caught in it as it closes, causing
serious injury or even death. Make
sure the opening is clear before
closing the sunroof.
Slide switch
Tilt switch
WARNING
J39L(02MY).book Page 19 Thursday, November 1, 2001 10:49 AM

3-20
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F

Tilt Operation
The rear of the sunroof can be tilted open
to provide more ventilation.
To tilt, push the rear of the tilt switch
located on the left side of the overhead
console.
To close, push the front of the tilt switch.

Slide Operation
To open to any position, press the rear of
the slide switch located on the right side
of the overhead console.
To close, press the front of the slide
switch.

Sunshade
The sunshade can be opened and closed
by hand.
The sunshade opens automatically when
the sunroof is opened, but must be closed
by hand.
NOTE
After washing your Mazda or after a
rain, wipe the water off the sunroof
before operating it.
Tilt up
Close
Open
Close
Sunshade
J39L(02MY).book Page 20 Thursday, November 1, 2001 10:49 AM

3-21
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F
The front cross bar is fixed in place.
The rear cross bar can be adjusted by
sliding it. The sunshade doesn’t tilt. To avoid
damaging the sunshade, don’t push up
on it.
CAUTIONRoof Rack
Rear cross bar
Front cross bar
J39L(02MY).book Page 21 Thursday, November 1, 2001 10:49 AM

3-22
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F

Roof Rack Adjustment
1. Loosen the screw at both ends of the
rear cross bar, then remove the rear
cross bar covers.
2. Loosen the bolt at both ends of the rear
cross bar, then slide the rear cross bar
to the desired position. •The roof rack is not designed for
direct placement of objects or loads.
A special attachment kit is
necessary. Consult an Authorized
Mazda Dealer.
•The maximum load on the roof rack
is 75 kg (165 lb). Do not overload.
•Because the bolts and screws may
loosen initially, retighten them.
Periodically check bolts for
looseness approximately every 100
km (62 miles).
•Avoid turning sharply and jamming
on the brakes while the roof rack
installed. Doing so may cause an
accident or the luggage may fall off.
•Road conditions (especially steep
curves or rough roads) and weather
changes (strong cross wind, head
wind, rain, snow, or fog) can change
vehicle operating characteristics
greatly when the vehicle is
equipped with the roof rack. To
cope with these conditions, drive at
a slower speed.
•When driving in a tunnel or parking
garage or any place with height
restrictions with the roof rack
installed, be aware that the roof rack
will raise the total clearance of the
vehicle.
•If the vehicle is washed in an
automatic car wash with the roof
rack installed, the roof rack or the
roof of the vehicle can be damaged.
Before washing the vehicle in an
automatic car wash, always remove
the roof rack.CAUTION
Screw
Rear cross bar coverRear cross bar
Bolt
J39L(02MY).book Page 22 Thursday, November 1, 2001 10:49 AM

3-23
Knowing Your Mazda
Doors and Locks
Form No. 8Q36-EA-01F
3. Tighten the bolt at both ends of the rear
cross bar alternately and evenly.
4. Install the rear cross bar cover by
inserting the clips into the square hole
of the rear cross bar until they click,
then tighten the screw.
NOTE
•If only one bolt is tightened, the
cross bar will lean to one side.
•Tighten the bolts with tightening
torque of 11—12 Nm {110—120
kgfcm}.
Bolt
Screw
Rear cross bar
cover
Rear cross bar
J39L(02MY).book Page 23 Thursday, November 1, 2001 10:49 AM

3-24
Knowing Your Mazda
Form No. 8Q36-EA-01F
Steering Wheel and Mirrors

Tilt Steering Wheel
To change the angle of the steering wheel,
stop the vehicle, pull the tilt wheel release
lever under the steering column down,
adjust the wheel, then push the release
lever up to lock the column.
After adjusting, push the wheel up and
down to be certain it’s locked before
driving.

Outside Mirrors
Check the mirrors’ angles before driving.
Manual control mirror
To adjust, move the mirror’s control lever,
just inside the door.
Steering Wheel
Adjusting the Steering Wheel:
Adjusting the steering wheel while the
vehicle is moving is dangerous.
Moving it can very easily cause the
driver to abruptly turn to the left or
right. This can lead to loss of control
or an accident. Never adjust the
steering wheel while the vehicle is
moving.
WARNING
Tilt wheel release
lever
Mirrors
Convex Mirror (Passenger Side):
Changing lanes without taking into
account the actual distance of the
vehicle in the convex mirror is
dangerous. You could have a serious
accident. What you see in the convex
mirror is closer than it appears. Be
sure to look over your shoulder or to
check your inside mirror before
changing lanes.
WARNING
Control lever
J39L(02MY).book Page 24 Thursday, November 1, 2001 10:49 AM