steering MAZDA MODEL RX 8 2004 (in English) User Guide

3-27
Knowing Your Mazda
Steering Wheel and Mirrors
Form No. 8R65-EA-03C
Auto-dimming mirror*
The auto-dimming mirror automatically
reduces glare of headlights from cars at
the rear when the ignition switch is in the
ON position.
Press the OFF button ( ) to cancel the
automatic dimming function. The
indicator light will go off.
To reactivate the automatic dimming
function, press the ON button ( ). The
indicator light will illuminate.
OFF button
ON button
Indicator light
NOTE
•Do not use glass cleaner or suspend
objects on or around the light
sensor. Otherwise, light sensor
sensitivity will be affected and may
not operate normally.
•For information regarding the
3 buttons ( , , ) on the
auto-dimming mirror, refer to
HomeLink Wireless Control
System (page 5-55).
Light sensor
Light sensor
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 27 Saturday, April 26, 2003 1:48 PM

4-7
Before Driving Your Mazda
Form No. 8R65-EA-03C
Driving Tips
No special break-in is necessary, but a
few precautions in the first 1,000 km
(600 miles) may add to the performance,
economy, and life of your Mazda.
•Don’t race the engine.
•Don’t maintain one constant speed for
long.
•Don’t drive constantly at full-throttle or
high engine rpm (over 7,000 rpm) for
extended periods of time.
•Avoid unnecessary hard stops.
•Avoid full-throttle starts.How you operate your Mazda determines
how far it will travel on a tank of fuel. Use
these suggestions to help save money on
fuel and repairs.
•Avoid long warm-ups. Once the engine
runs smoothly, begin driving.
•Avoid fast starts.
•Keep the engine tuned. Follow the
maintenance schedule (page 8-3) and
have an Authorized Mazda Dealer
perform inspections and servicing.
•Use the air conditioner only when
necessary.
•Slow down on rough roads.
•Keep the tires properly inflated.
•Don’t carry unnecessary weight.
•Don’t rest your foot on the brake pedal
while driving.
•Keep the wheels in correct alignment.
•Keep windows closed at high speeds.
•Slow down when driving in crosswinds
and headwinds.
Break-In PeriodMoney-Saving Suggestions
Coasting:
Stopping the engine when going down
a hill is dangerous. This causes the
loss of power steering and power
brake control, and may cause damage
to the drivetrain. Any loss of steering
or braking control could cause an
accident. Never stop the engine when
going down a hill.
WARNING
J60E_8R65-EA-03C_Edition2.book Page 7 Saturday, April 26, 2003 1:48 PM

4-8
Before Driving Your Mazda
Driving Tips
Form No. 8R65-EA-03C
When driving on ice or in water, snow,
mud, sand, or similar hazard:
•Be cautious and allow extra distance
for braking.
•Avoid sudden braking and quick
steering.
•If your vehicle is not equipped with
ABS, brake with the pedal by using a
light up-down motion. Don’t hold the
pedal down constantly.
If your vehicle is equipped with ABS,
don’t pump the brakes. Continue to
press down on the brake pedal.
•If you get stuck, select a lower gear and
accelerate slowly. Don’t spin the rear
wheels.
•For more traction in starting on
slippery surfaces such as ice or packed
snow, use sand, rock salt, chains,
carpeting, or other nonslip material
under the rear wheels.If you must rock the vehicle to free it from
snow, sand, or mud, depress the
accelerator slightly and slowly move the
shift lever from 1 (D) to R.
Hazardous Driving
Downshifting on Slippery Surfaces:
Downshifting into lower gear while
driving on slippery surfaces is
dangerous. The sudden change in tire
speed could cause the tires to skid.
This could lead to loss of vehicle
control and an accident. If it is
necessary to downshift on slippery
surfaces, be very careful.
NOTE
Use snow chains only on the rear
wheels.
WARNING
Rocking the Vehicle
Spinning the Wheels:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tire could overheat and
explode. This could cause serious
injuries. Don’t spin the wheels at
more than 56 km/h (35 mph), and
don’t allow anyone to stand behind a
wheel when pushing the vehicle.
Too much rocking may cause engine
overheating, transmission failure, and
tire damage.
WARNING
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 8 Saturday, April 26, 2003 1:48 PM

5-1
Form No. 8R65-EA-03C
5Driving Your Mazda
Explanation of instruments and controls.
Starting and Driving
..................................................................... 5-2
Ignition Switch .......................................................................... 5-2
Starting the Engine .................................................................... 5-3
Brake System ............................................................................. 5-4
Manual Transmission Operation ............................................... 5-8
Automatic Transmission Controls ........................................... 5-10
Power Steering ......................................................................... 5-16
Cruise Control ......................................................................... 5-17
Traction Control System (TCS)* ............................................. 5-20
Dynamic Stability Control (DSC)* ......................................... 5-21
Tire Pressure Monitoring System* .......................................... 5-24
Instrument Cluster and Indicators
............................................ 5-29
Meters and Gauges .................................................................. 5-29
Warning/Indicator Lights and Beeps
........................................ 5-35
Warning/Indicator Lights ......................................................... 5-35
Beeps ....................................................................................... 5-47
Switches and Controls
................................................................. 5-48
Lighting Control ...................................................................... 5-48
Turn and Lane-Change Signals ............................................... 5-50
Fog Lights* .............................................................................. 5-50
Windshield Wipers and Washer ............................................... 5-51
Headlight Washer* .................................................................. 5-53
Rear Window Defroster ........................................................... 5-53
Horn ......................................................................................... 5-54
Hazard Warning Flasher .......................................................... 5-55
HomeLink Wireless Control System* ..................................... 5-55
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 1 Saturday, April 26, 2003 1:48 PM

5-2
Driving Your Mazda
Form No. 8R65-EA-03C
Starting and Driving

Ignition Switch Positions
LOCK
The steering wheel locks to protect
against theft. Only in this position can the
key be removed.
Manual transmission
When turning the ignition switch to the
LOCK position, push the key in at the
ACC position.Automatic transmission
When turning the ignition switch to the
LOCK position, keep the shift lever in P.
Ignition Switch
LOCK
Push the key ACCON
Removing the Key:
It’s dangerous to remove the key from
the ignition switch while the vehicle is
moving. Removing the key allows the
steering wheel to lock. You will lose
steering control and a serious
accident could occur.
Remove the key only when the vehicle
is parked.
Not Setting the Parking Brake:
Leaving the driver’s seat without
setting the parking brake is
dangerous. Unexpected vehicle
movement could occur if the parking
brake is not set. This could cause an
accident. Before leaving the driver’s
seat, always set the parking brake and
make sure the shift lever is in P with
an automatic transmission or in 1 or
R with a manual transmission.
LOCKShift lever
engaged in P
(park) ACCON
WARNING
J60E_8R65-EA-03C_Edition2.book Page 2 Saturday, April 26, 2003 1:48 PM

5-3
Driving Your Mazda
Starting and Driving
Form No. 8R65-EA-03C
ACC (Accessory)
The steering wheel unlocks and some
electrical accessories will operate.
ON
This is the normal running position after
the engine is started. The warning lights
(except brakes) should be inspected
before the engine is started (page 5-35).
START
The engine is started in this position. It
will crank until you release the key; then
it returns to the ON position. The brake
warning light can be checked after the
engine is started (page 5-35).

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when the
driver’s door is opened.1. Occupants should fasten their seat
belts.
2. Make sure the parking brake is on.
3. Depress the brake pedal.
4.(Manual transmission)

Depress the clutch pedal all the way
and shift into neutral.
Keep the pedal depressed while
cranking the engine.
(Automatic transmission)

Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
If turning the key is difficult, jiggle the
steering wheel from side to side.
NOTE
(Xenon fusion headlight models)

When the ignition switch is turned to
the ON position, the sound of the
headlight leveling motors operating at
the front of the engine compartment
can be heard. This does not indicate an
abnormality.
Starting the Engine
NOTE
Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of
radio noise.
NOTE
The starter will not operate if the
clutch pedal is not
pushed down all the
way.
NOTE
The starter will not operate if the shift
lever is not
in P or N.
J60E_8R65-EA-03C_Edition2.book Page 3 Saturday, April 26, 2003 1:48 PM

5-11
Driving Your Mazda
Starting and Driving
Form No. 8R65-EA-03C
D (Drive)
D is the normal driving position. From a
stop, the transmission will automatically
shift through a 4-gear sequence.
M (Manual)
M is the manual shift mode position.
Gears can be shifted up or down by
operating the shift lever or steering shift
switches.
Refer to Manual Shift Mode (page 5-11).

Shift-Lock System
The shift-lock system prevents shifting
out of P unless the brake pedal is
depressed.

To shift from P:
1. Depress and hold the brake pedal.
2. Start the engine.
3. Move the shift lever.

Manual Shift Mode
This mode gives you the feel of driving a
manual transmission vehicle by operating
the shift lever or steering shift switches
and allows you to control engine rpm and
torque to the rear wheels much like a
manual transmission when more control is
desired.
To change to manual shift mode, shift the
lever from D to M.
To return to automatic shift mode, shift
the lever from M to D.
Shifting from N or P:
It’s dangerous to shift from N or P
into a driving gear when the engine is
running faster than idle. If this is
done, the vehicle could move
suddenly, causing an accident or
serious injury. If the engine is
running faster than idle, don’t shift
from N or P into a driving gear.
Shifting into N while Driving:
Shifting into N while driving is
dangerous. Engine braking cannot be
applied when decelerating which
could lead to an accident or serious
injury. Do not shift into N when
driving the vehicle.
Do not shift into N when driving the
vehicle. Doing so can cause
transmission damage.
WARNING
CAUTION
NOTE
•When the ignition switch is in the
LOCK position, the transaxle
cannot be shifted from P.
•To be sure the vehicle is in park,
the ignition key cannot be
removed unless the shift lever is in
P.
J60E_8R65-EA-03C_Edition2.book Page 11 Saturday, April 26, 2003 1:48 PM

5-12
Driving Your Mazda
Starting and Driving
Form No. 8R65-EA-03C
Indicators
Shift position indicator
In manual shift mode, the "M" of the shift
position indicator in the instrument panel
illuminates.
Gear position indicator
In manual shift mode, the numeral for the
selected gear illuminates.Shifting
You can shift gears up and down by
operating the shift lever or the steering
shift switches.NOTE
•If you change to manual shift mode
when the vehicle is stopped, the
gear will shift to M1.
•If you shift up once when the
vehicle is stopped and the gear is at
M1, the gear will shift to M2. M2 is
helpful for starting on slippery
surfaces.
NOTE
If the gears cannot be shifted down
when driving at higher speeds, the gear
position indicator will flash twice to
signal that the gears cannot be shifted
down.
Gear position
indicator
Shift position
indicator
NOTE
•If the steering shift switches on both
sides (left and right) are operated
simultaneously, the gear will shift
once.
•The gear will not shift if:
The steering shift switch and the
shift lever are operated
simultaneously.
The UP switch and DOWN
switch are operated
simultaneously.
J60E_8R65-EA-03C_Edition2.book Page 12 Saturday, April 26, 2003 1:48 PM

5-13
Driving Your Mazda
Starting and Driving
Form No. 8R65-EA-03C
Manually shifting up
(M1
→M2
→M3
→M4)
To shift up to a higher gear with the shift
lever, tap the shift lever back (+) once.To shift up to a higher gear with the
steering shift switches, tap either of the
UP switches toward you once with your
fingers.
NOTE
•When driving slowly, the gears may
not shift up depending on vehicle
speed.
•In manual shift mode, gears do not
shift up automatically. Don’t run the
engine with the tachometer needle
in the RED ZONE. If the
tachometer needle enters the RED
ZONE, you may feel engine-
braking because the fuel delivery
will be stopped to protect the
engine. However, this does not
indicate an abnormality.
•Gears may not be shifted from M1
to M2 right after shifting the lever
from D to M. Wait a few seconds
and then shift up to M2.
•When depressing the accelerator
fully, the transmission will shift to a
lower gear, depending on vehicle
speed.
Hand Position When Using Steering
Shift Switches:
Putting your hands inside the rim of
the steering wheel when using the
steering shift switches is dangerous.
If the driver air bag were to deploy in
a collision, your hands could be
impacted causing injury. Keep your
hands on the steering wheel rim when
using fingers or thumbs on the
steering shift switches.
UP switches
WARNING
J60E_8R65-EA-03C_Edition2.book Page 13 Saturday, April 26, 2003 1:48 PM

5-14
Driving Your Mazda
Starting and Driving
Form No. 8R65-EA-03C
Manually shifting down
(M4
→M3
→M2
→M1)
To shift down to a lower gear with the
shift lever, tap the shift lever forward (-)
once.To shift down to a lower gear with the
steering shift switches, press either of the
DOWN switches away from you once
with your thumb.
Sudden Engine-Braking:
Shifting down while driving on wet,
snowy, or frozen roads, or while
driving at high speeds causes sudden
engine braking, which is dangerous.
The sudden change in tire speed
could cause the tires to skid. This
could lead to loss of vehicle control
and an accident. Do not use sudden
engine braking on slippery road
surfaces or at high speeds.
NOTE
•When driving at high speeds, the
gear may not shift down depending
on vehicle speed.
•During deceleration, the gear may
automatically shift down depending
on vehicle speed.
•When depressing the accelerator
fully, the transmission will shift to a
lower gear, depending on vehicle
speed.
WARNING
Hand Position When Using Steering
Shift Switches:
Putting your hands inside the rim of
the steering wheel when using the
steering shift switches is dangerous.
If the driver air bag were to deploy in
a collision, your hands could be
impacted causing injury. Keep your
hands on the steering wheel rim when
using fingers or thumbs on the
steering shift switches.
DOWN switches
WARNING
J60E_8R65-EA-03C_Edition2.book Page 14 Saturday, April 26, 2003 1:48 PM