relay MAZDA MX-5 1994 Manual PDF

T HORN Symptom: Horn does not sound. 05UOTX-191 Step 1 1. Check the STOP 15A fuse. 2. If the fuse is burned, replace it. Check and repair the wire harness, if necessary. 3. If the fuse is OK, go to Step 2. Step 2 1. Disconnect the horn connector. 2. Apply battery positive voltage to the horn, and check if the horn sounds. 3. If the horn sounds, go to Step 3. 4. If the horn does not sound, replace the horn. Step 3 1. Remove the knee protector. 2. Ground the terminal B (GIO) of the horn relay connector. 3. If the horn sounds, go to Step 4. 4. If the horn does not sound, go to Step 6. Step 4 1. Disconnect the negative battery cable. 2. Remove the air bag module. (Refer to page T-204.) 3. Check for continuity between the terminal of the horn switch connector and the steering shaft. I OFF I No I Horn switch ON 4. If correct, go to Step 5. 5. If not as specified, replace the horn switch and steering wheel as an assembly. Verify that the air bag system is operating normally by monitoring the air bag warning light. Continuity Yes Gartner Banana

HORN T Step 6 1. Ground the terminal B (GIO) of the horn relay connector. 2. Measure the voltage at the following terminal wires of the horn relay connector. Step 5 1. Remove the knee protector. 2. Disconnect the clock spring connector. 3. Check for continuity of the clock spring connector as shown in the figure. B+: Batterv ~ositive voltaae Continuity Yes No A (WIG) Actlon Repair wiring harness (Horn relay - Clock spring connector) Replace combination switch D (WIG) Voltage B+ Repair wiring harness Other I (STOP l5A fuse - Horn relay) Action Check D terminal Other B+ Repair wiring harness (STOP 15A fuse - Horn relay) Check C terminal REMOVAL I INSTALLATION Horn Remove and install as shown in the figure. Horn Switch 1. Disconnect the negative battery cable. u C (GIR) '+ Other Repair wiring harness (Horn relay - Horn) Replace horn relay Gartner Banana

REAR WINDOW DEFROSTER REAR WINDOW DEFROSTER STRUCTURAL VIEW 1. Rear window defroster L/ 2. Rear window defroster switch 3. Rear window defroster relay 4. Rear window defroster timer unit DESCRIPTION The rear window defroster switch is included in the heater control switch assembly. Gartner Banana

FUSE BCOCK IX-031 I 1,05);;;! rAR WINOOW OEFROSTER 1-05 --: RELAY FUSE BLOCK 1-2 .CIGARETTE LIGHTER .INTERIOR LIGHT .REAR WINDOW DEFROSTER MAIN FUSE BLOCK FUSE BLOCK W/R (F) -- ;; ROOM L/R (FI IX-04 'OA &g [x-ZZI 1 - eh FUSE CONTROL MOOUCE (EWGINEI (SECTION 8- tc) INSTRVMENT CLUSTER (SECTION C-a) t OOW SWITCHES (SECTION T) INTERIOR LIGHT OFF. ON !;. (I1 OB CIGARETTE L .IGHTER (I) 1-09 INTERIOR LIGHT (11 I I Z-10 REAR WINOOW DEFROSTER SWITCH (I) I Gartner Banana

REAR WINDOW DEFROSTER T u Symptom: Rear window defroster does not operate. 9MUOTX-232 Step 1 1. Check the following fuses. I Fuse Amperage I Location I 2. If all the fuses are OK, go to Step 2. 3. If a fuse is burned out, replace it. Check and repair the wire harness, if necessary. R.DEF HEATER -- M: Continuity 20A 30A Step 2 1. Disconnect the rear window defroster relay. 2. Apply battery positive voltage and check for continuity between terminals of the relay. B+: Battery positive voltage 3. If correct install the rear window defroster relay and go to Step 3. 4. If not as specified, replace the rear window defroster relay. Fuse box No.2 Main fuse block Step 1 2 C Terminal D 0 GND B 0 B+ A 0 C 0 Gartner Banana

T REAR WINDOW DEFROSTER Step 3 1. Turn the ignition switch to on. 2. Turn the rear window defroster switch on. 3. Check the voltage at the terminal wires of the rear win- d dow defroster rday connector. B+: Battery positive voltage Terminal (uB) c (R) Step 4 Check if the heater operates in the first position. I Operation I Action I Voltage B+ other NG Repair wiring harness (Heater switch- Rear window defrostertimer unit) Action Check C terminal Repair wiring harness (HEATER fuse - Relav) B+ Other . , Go to Step 4 Go to Step 5 I Step 5 Check the voltage at the rear window defroster connec- tors. Check A terminal Repair wiring harness (DEFOG fuse - Relavl A (w) B+: Battery positive voltage B+ Other Terminal I Voltage I Action B+ I Check C terminal other If all above-mentioned parts are normal, replace the rear window defroster timer unit. Repair wiring harness (Defroster - Defroster timer unit) c (W) A (B) . B+ Other B+ Other Check A terminal Repair wiring harness (Relay- Defroster) Repair wiring harness (Defroster - GND) Repair defroster filament Gartner Banana

AUDIO T POWER ANTENNA Disassembly 1 Assembly 1. Antenna mast 2. Base 3. Base pad ,, 4. Ground plate 5. Ground base 6. Rod insulator 7. Mast assembly 8. Relay bracket 9. Antenna relay 10. Bracket 11. Motor drive unit 12. Drive mechanism 13. Drive mechanism cover Gartner Banana

Ix-osl, FUSE ANTENNA BLOCK 1OA 8 R/B J-3 MAIN FUSE BLOCK .POWER ANTENNA MAIN IGNITION m SWITCH L~W PMR ANTENNA MOTOR BR I I T Y w -13 REAR [R) -POHER ANTENNA ASSEMBLY J-14 POWER ANTENNA RELAY I I I Gartner Banana

AUDIO Inspection c Fuse ness. ml JHFDB If the antenna fails to raise or lower, make the following checks: 1. Check the antenna fuse (10A). 2. Replace fuse after checking and repairing wiring har- Power antenna 1. Check for continuity between the terminals of the power antenna relay. If there is no continuity, replace the relay. Terminal I M: Continuity 2. If the antenna does not function even though there is continuity, the problem may be either in the wiring har- ness or in the audio component assembly. 3. Apply battery positive voltage to the terminals and check the operation. I I A 1 B 1 DOWN I Function of antenna UP Battery Pos. D Neg. A Gartner Banana

SRS AIR BAG SYSTEM SYSTEM DIAGRAM PASSENGER-SIDE S-SENSOR AIR BAG MODULE I IG1 B+ HORN RELAY CLOCK SPRING BACK-UP BATTERY I AIR BAG SYSTEM WARNING LIGHT SENSOR -7 System Operation During collision When either of the D-sensors and the S-sensor are activated (closed) simultaneously by shock of a colli- sion, the circuit to the inflator is completed. The inflator creates nitrogen gas and the air bag is deployed. The air bag vents the nitrogen gas from the vent hole on the back side of the bag to reduce shock to the driver and to allow easier exit from the vehicle. During normal condition and malfunction The diagnostic module constantly monitors the components and wiring of the air bag system for malfunc- tion, open circuits, and short circuits. .J If a malfunction is detected, the diagnostic module illuminates or flashes the warning light. In the case of a short circuit in the sensors or sensor harnesses, the diagnostic module activates the warning light and shuts down the system to prevent accidental deployment of the air bag. Gartner Banana