lock MAZDA MX5 MIATA 2017 Owners Manual

6 –14 Maintenance and Care
Scheduled Maintenance Schedule 1 Maintenance Interval Number of months or kilometers, whichever comes first
Months 6 12 18 24 30 36 42 48 54 60 66 72
×1000 km 10 20 30 40 50 60 70 80 90 100 11 0 120
ENGINE
Drive belts I I I
Engine oil & filter R R R R R R R R R R R R
COOLING SYSTEM
Cooling system I I I
Engine coolant *1
Replace at first 200,000 km or 10 years; after that, every
100,000 km or 5 years
FUEL SYSTEM
Air filter R R R R R R
Fuel lines and hoses I *2
I *2
I
Hoses and tubes for emission I *2
I *2
I
Fuel filter Replace every 60,000 km
IGNITION SYSTEM
Spark plugs I I I I I I I I I I I I
Replace every 120,000 km
CHASSIS and BODY
Brake lines, hoses and connections I I I I I I
Brake and clutch fluid level I I I I I I I I I
Brake fluid R R R
Disc brakes I I I I I I I I I I I I
Manual transmission oil R
Tire (Rotation) *3
Rotate every 10,000 km
Tire inflation pressure and tire wear *3
I I I I I I I I I I I I
Steering operation and linkages I I I I I I I I I I I I
Front and rear suspension, ball joints and wheel
bearing axial play I I I I I I
Rear differential oil *4
Driveshaft dust boots I I I I I I
Bolts and nuts on chassis and body T T T T T T
Exhaust system and heat shields I I I I I I
All locks and hinges L L L L L L L L L L L L
Washer fluid level I I I I I I I I I I I I
Emergency flat tire repair kit (if installed) *5
Inspect annually.
MX-5_8FR4-EA-16J_Edition1.indb 14 2016/08/11 20:29:40

6 –16 Maintenance and Care
Scheduled Maintenance Schedule 2 Maintenance Interval Number of months or kilometers, whichever comes first
Months 3 6 9 12 15 18 21 24 27 30 33 36
×1000 km 5 10 15 20 25 30 35 40 45 50 55 60
ENGINE
Drive belts I
Engine oil & filter R R R R R R R R R R R R
COOLING SYSTEM
Cooling system I
Engine coolant *1
Replace at first 200,000 km or 10 years; after that, every
100,000 km or 5 years
Engine coolant level I I I I I I I I I I I I
FUEL SYSTEM
Air filter C R C R C R
Fuel lines and hoses I *2
Hoses and tubes for emission I *2
Fuel filter Replace every 60,000 km
IGNITION SYSTEM
Spark plugs I I I I I I
Replace every 120,000 km
ELECTRICAL SYSTEM
Function of all lights I I I I I I I I I I I I
CHASSIS and BODY
Brake lines, hoses and connections I I I
Brake and clutch fluid level I I I I I
Brake fluid R
Disc brakes I I I I I I
Manual transmission oil R
Tire (Rotation) *3
Rotate every 10,000 km
Tire inflation pressure and tire wear *3
I I I I I I
Steering operation and linkages I I I I I I
Front and rear suspension, ball joints and wheel
bearing axial play I I I
Rear differential oil *4
Driveshaft dust boots I I I
Bolts and nuts on chassis and body T T T
Exhaust system and heat shields I I I
All locks and hinges L L L L L L
MX-5_8FR4-EA-16J_Edition1.indb 16 2016/08/11 20:29:40

6 –18 Maintenance and Care
Scheduled Maintenance (Cont.) Maintenance Interval Number of months or kilometers, whichever comes first
Months 39 42 45 48 51 54 57 60 63 66 69 72
×1000 km 65 70 75 80 85 90 95 100 105 11 0 11 5 120
ENGINE
Drive belts I I
Engine oil & filter R R R R R R R R R R R R
COOLING SYSTEM
Cooling system I I
Engine coolant *1
Replace at first 200,000 km or 10 years; after that, every
100,000 km or 5 years
Engine coolant level I I I I I I I I I I I I
FUEL SYSTEM
Air filter C R C R C R
Fuel lines and hoses I *2
I
Hoses and tubes for emission I *2
I
Fuel filter Replace every 60,000 km
IGNITION SYSTEM
Spark plugs I I I I I I
Replace every 120,000 km
ELECTRICAL SYSTEM
Function of all lights I I I I I I I I I I I I
CHASSIS and BODY
Brake lines, hoses and connections I I I
Brake and clutch fluid level I I I I
Brake fluid R R
Disc brakes I I I I I I
Manual transmission oil R R
Tire (Rotation) *3
Rotate every 10,000 km
Tire inflation pressure and tire wear *3
I I I I I I
Steering operation and linkages I I I I I I
Front and rear suspension, ball joints and wheel
bearing axial play I I I
Rear differential oil *4
Driveshaft dust boots I I I
Bolts and nuts on chassis and body T T T
Exhaust system and heat shields I I I
All locks and hinges L L L L L L
MX-5_8FR4-EA-16J_Edition1.indb 18 2016/08/11 20:29:41

6 –24 Maintenance and Care
Owner Maintenance
HoodWARNINGAlways check that the hood is closed
and securely locked:
A hood that is not closed and securely
locked is dangerous as it could fly open
while the vehicle is moving and block
the driver's vision which could result in
a serious accident.
Opening the Hood1. With the vehicle parked, pull the
release handle to unlock the hood.

Release handle 2. Insert your hand into the hood opening,
slide the latch lever to the right, and lift
up the hood.

Le ve r
3. Grasp the support rod in the padded
area and secure it in the support rod
hole indicated by the arrow to hold the
hood open.
Pa d
Support rod
Clip
MX-5_8FR4-EA-16J_Edition1.indb 24 2016/08/11 20:29:42

6 –26 Maintenance and Care
Owner Maintenance
Engine Compartment OverviewW indshield washer fluid reservoir Brake/Clutch fluid reservoir
Engine oil dipstick
Battery Fuse blockCooling system cap
Engine coolant reservoirEngine oil-filler cap
MX-5_8FR4-EA-16J_Edition1.indb 26 2016/08/11 20:29:42

6 –32 Maintenance and Care
Owner Maintenance Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.
Use plain water if washer fluid is
unavailable.
But use only washer fluid in cold weather
to prevent it from freezing. Body Lubrication All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the hood's secondary latch
keeps the hood from opening when the
primary latch is released.
MX-5_8FR4-EA-16J_Edition1.indb 32 2016/08/11 20:29:44

6 –34 Maintenance and Care
Owner Maintenance 3. Tilt the blade assembly and remove it
from the arm.
CAUTION To prevent damage to the windshield
let the wiper arm down easily, do not
let it slap down on the windshield.
4. Pull down the blade rubber and slide it
out of blade holder.
5. Remove the metal stiffeners from each
blade rubber and install them in the
new blade. CAUTION 
Do not bend or discard the stiffeners. You
need to use them again. 
If the metal stiffeners are switched,
the blade's wiping efficiency could be
reduced.
So do not use the driver's side metal
stiffeners on the passenger's side, or vice
versa. 
Be sure to reinstall the metal stiffeners in
the new blade rubber so that the curve
is the same as it was in the old blade
rubber.
6. Carefully insert the new blade rubber.
Then install the blade assembly in the
reverse order of removal.
(Type B)
1. Raise the wiper arm and turn the blade
assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm.
Plastic locking clip
MX-5_8FR4-EA-16J_Edition1.indb 34 2016/08/11 20:29:45

6 –46 Maintenance and Care
Owner Maintenance
CAUTION When removing the lens or lamp unit
using a flathead screwdriver, make
sure that the flathead screwdriver does
not contact the interior terminal. If
the flathead screwdriver contacts the
terminal, a short circuit may occur.
NOTE 
To replace the bulb, contact an
Authorized Mazda Dealer. 
Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
Replacing Exterior Light BulbsHeadlights, Daytime running lights
(LED type), Parking lights, High-mount
brake light, Brake lights, Taillights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary. Daytime running lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers.
Rem ova l
Installation
3. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.

4. Turn the socket and bulb assembly
counterclockwise and remove it.
MX-5_8FR4-EA-16J_Edition1.indb 46 2016/08/11 20:29:48

6 –47 Maintenance and Care
Owner Maintenance5. Disconnect the bulb from the socket.

6. Install the new bulb in the reverse order
of the removal procedure.
Front side-marker lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Rem ova l
Installation
4. Turn the socket and bulb assembly
counterclockwise and remove it. 5. Disconnect the bulb from the socket.

6. Install the new bulb in the reverse order
of the removal procedure.
Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Rem ova l
Installation
MX-5_8FR4-EA-16J_Edition1.indb 47 2016/08/11 20:29:48

6 –48 Maintenance and Care
Owner Maintenance 4. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector rearward.

5. Turn the socket and bulb assembly
counterclockwise and remove it.
6. Disconnect the bulb from the socket.

7. Install the new bulb in the reverse order
of the removal procedure.
Side turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left. 3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Rem ova l
Installation
4. Remove the unit by pressing the tab on
the unit with your finger and pulling the
unit forward.

5. Detach the electrical connector from
the unit by pulling it to the rear.

6. Install the new side turn signal unit
in the reverse order of the removal
procedure.
MX-5_8FR4-EA-16J_Edition1.indb 48 2016/08/11 20:29:48