turn signal MAZDA MX5 MIATA 2017 User Guide

4 –50 When Driving
Switches and Controls
Turn and Lane-Change
Signals The ignition must be switched ON to use
the turn and lane-change signals.
Turn SignalsMove the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to its
original position. Right turn
Left turnRight lane change
Left lane change OFF
The turn signal indicators in the instrument
cluster flash according to the operation of
the turn signal lever to show which signal
is working. NOTE 
If an indicator light stays on without
flashing or if it flashes abnormally, one
of the turn signal bulbs may be burned
out. 
A personalized function is available to
change the turn indicator sound volume.
(page 9-9 )
Lane-Change Signals Move the lever halfway toward the
direction of the lane change—until the
indicator flashes— and hold it there. It will
return to the off position when released.
Three-Flash Turn Signal After releasing the turn signal lever, the
turn signal indicator flashes three times.
The operation can be cancelled by moving
the lever in the direction opposite to which
it was operated.
NOTE
The three-flash turn signal function can be
switched to operable/inoperable using the
personalization function.
Refer to Personalization Features on page
9-9 .
MX-5_8FR4-EA-16J_Edition1.indb 50 2016/08/11 20:28:54

4 –57 When Driving
Switches and Controls
*Some models.Hazard Warning Flasher The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning flasher and
all the turn signals will flash. The hazard
warning indicator lights in the instrument
cluster flash simultaneously.
NOTE 
The turn signals do not work when the
hazard warning lights are on. 
Check local regulations about the use of
hazard warning lights while the vehicle
is being towed to verify that it is not in
violation of the law. HomeLink Wireless
Control System *
NOTE
HomeLink and HomeLink house icon
are registered trademarks of Gentex
Corporation.
The HomeLink system replaces up to
3 hand-held transmitters with a single
built-in component in the auto-dimming
mirror. Pressing the HomeLink button on
the auto-dimming mirror activates garage
doors, gates and other devices surrounding
your home.
HomeLink button Indicator light
MX-5_8FR4-EA-16J_Edition1.indb 57 2016/08/11 20:28:55

4 –60 When Driving
Switches and Controls 9. Return to the vehicle and firmly press,
hold for two seconds and release the
programmed HomeLink button. Repeat
the “ press/hold/release ” sequence a
second time, and, depending on the
brand of the garage door opener (or
other rolling code equipped device),
repeat this sequence a third time to
complete the programming process.
HomeLink should now activate your
rolling code equipped device.
NOTE
To program the remaining two HomeLink
buttons, begin with “Programming” —
step 1
For questions or comments, please contact
HomeLink at www.homelink.com or 1-
800-355-3515 .
Gate operator/Canadian
ProgrammingCanadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
— which may not be long enough for
HomeLink to pick up the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are designed
to “time-out” in the same manner.
If you live in Canada or you are having
difficulties programming a gate operator
by using the “Programming” procedures
(regardless of where you live), replace
“Programming HomeLink” step 3 with
the following:
NOTE
If programming a garage door opener or
gate operator, it is advised to unplug the
device during the “cycling” process to
prevent possible overheating. Continue to press and hold the HomeLink
button while you press and release
— every two seconds (“cycle”) your
hand-held transmitter until the frequency
signal has successfully been accepted by
HomeLink. (The indicator light will flash
slowly and then rapidly.)
Proceed with “Programming” step 4 to
complete.
Operating the HomeLink System Press the programmed HomeLink button
to operate a programmed device. The
code will continue being transmitted for a
maximum of 20 seconds.
Reprogramming the HomeLink
system To program a device to HomeLink using
a HomeLink button previously trained,
follow these steps:
1. Press and hold the desired HomeLink
button. DO NOT release the button.
2. The indicator light will begin to flash
after 20 seconds. Without releasing
the HomeLink button, proceed with
“Programming” - step 1.
Erasing Programmed HomeLink
Buttons
To erase the existing programming from
all three operating channels, press and
hold the two outside buttons (
, ) on
the auto-dimming mirror until the
HomeLink indicator light begins to flash
after approximately 10 seconds.
Verify that the programming has been
erased when you resell the vehicle.
MX-5_8FR4-EA-16J_Edition1.indb 60 2016/08/11 20:28:56

4 –77 When Driving
i-ACTIVSENSENOTE
The timing in which the system switches the headlights changes under the following
conditions. If the system does not switch the headlights appropriately, manually switch
between high and low beams according to the visibility as well as road and traffic
conditions. 
When there are sources of light in the area such as street lamps, illuminated signboards,
and traffic signals. 
When there are reflective objects in the surrounding area such as reflective plates and
signs. 
When visibility is reduced under rain, snow and foggy conditions. 
When driving on roads with sharp turn or hilly terrain. 
When the headlights/rear lamps of vehicles in front of you or in the opposite lane are dim
or not illuminated. 
When there is sufficient darkness such as at dawn or dusk. 
When the luggage compartment is loaded with heavy objects. 
When visibility is reduced due to a vehicle in front of you spraying water from its tires
onto your windshield.
MX-5_8FR4-EA-16J_Edition1.indb 77 2016/08/11 20:29:00

4 –80 When Driving
i-ACTIVSENSE
CAUTION Do not modify the suspension. If the vehicle height or the damping force of the
suspensions is changed, the LDWS may not operate correctly.
NOTE 
If your vehicle deviates from its traffic lane, the LDWS operates (warning sound and
indicator light). Steer the vehicle adequately to drive the vehicle to the center of the lane. 
When the turn signal lever is operated for a lane change, the LDWS warning is
automatically canceled. The LDWS warning becomes operable when the turn signal lever
is returned and the system detects the white or yellow lines. 
If the steering wheel, accelerator pedal, or brake pedal is operated abruptly and the
vehicle moves close to a white or yellow line, the system determines that the driver is
making a lane change and the LDWS warning is automatically canceled. 
The LDWS may not operate during the period immediately after the vehicle has deviated
from its lane and the LDWS has operated, or the vehicle deviates from its lane repeatedly
within a short period of time. 
The LDWS does not operate if it does not detect the white or ye llow lines of the traffic
lane.
MX-5_8FR4-EA-16J_Edition1.indb 80 2016/08/11 20:29:01

4 –83 When Driving
i-ACTIVSENSEAuto cancel warning
When the following operations are
performed, the LDWS determines that
the driver intends to make a lane change
and the LDWS warning is canceled
automatically. The LDWS is enabled
automatically after the driver performs the
operation. 
The steering wheel is operated abruptly. 
The brake pedal is depressed abruptly. 
The accelerator pedal is depressed
abruptly. 
The turn signal lever is operated (after
the turn signal lever is returned, the
LDWS may not operate for about 3
seconds which is the period of time
required to make a lane correction).
NOTE
After about 60 seconds have elapsed with
the turn signal lever left operating, the
LDWS warning may operate if the vehicle
is close to a white or yellow line.
Canceling the SystemPress the LDWS OFF switch to cancel the
LDWS. The LDWS OFF indicator light
turns on.
Vehicle lane display (vehicles with
multi-information display)
The vehicle lane lines are no longer
indicated in the multi-information display
when the LDWS is canceled. NOTE
When the ignition is switched OFF, the
LDWS becomes operational the next time
the ignition switched ON.
LDWS Warning If the system determines that there is the
possibility of a lane departure, the LDWS
warning beep activates and the LDWS
warning light flashes. Operate the steering
wheel appropriately and steer the vehicle
to the center of the lane.
For vehicles equipped with the multi-
information display and the active driving
display, the color of the lane line in the
direction which the system determined
that the vehicle may be deviating from its
lane changes from white to amber and the
vehicle lane line flashes.
Indication on display
MX-5_8FR4-EA-16J_Edition1.indb 83 2016/08/11 20:29:01

4 –85 When Driving
i-ACTIVSENSE
*Some models.Blind Spot Monitoring (BSM) System *
The Blind Spot Monitoring (BSM) is designed to assist the drive r in checking the area to the
rear of the vehicle on both sides during lane changes by alerting the driver to the presence of
vehicles approaching from the rear in an adjacent lane.
The Blind Spot Monitoring (BSM) detects vehicles approaching fr om the rear while
traveling in the forward direction at a speed of 10 km/h (6.3 mph) or faster and turns on the
Blind Spot Monitoring (BSM) warning lights equipped on the door mirrors depending on
the conditions. If the turn signal lever is operated to signal a lane change in the direction
in which the Blind Spot Monitoring (BSM) warning light is illum inated, the system warns
the driver of a vehicle in the detection area by flashing the Bl ind Spot Monitoring (BSM)
warning light and activating a beep sound.
The detection area on this system covers the driving lanes on both sides of the vehicle and
from the rear part of the doors to about 50 m (164 ft) behind the vehicle.
Detection areasYour vehicle
WARNING Always check the surrounding area visually before making an actual lane change:
The system is only designed to assist you in checking for vehicles at your rear when
making a lane change. Due to certain limitations with the operation of this system, the
Blind Spot Monitoring (BSM) warning light may not flash or it might be delayed even
though a vehicle is in an adjacent driving lane. Always make it your responsibility as a
driver to check the rear.
MX-5_8FR4-EA-16J_Edition1.indb 85 2016/08/11 20:29:02

4 –88 When Driving
i-ACTIVSENSE 
In the following cases, it may be difficult to view the illumina tion/flashing of the Blind
Spot Monitoring (BSM) warning lights equipped on the door mirrors. 
Snow or ice is adhering to the door mirrors. 
The door glass is fogged or covered in snow, frost or dirt. 
The system switches to the Rear Cross Traffic Alert function when the shift lever (manual
transmission) or the selector lever (automatic transmission) is shifted to the reverse (R)
position.
Refer to Rear Cross Traffic Alert (RCTA) on page 4-92 .
Blind Spot Monitoring (BSM) Warning Lights/Blind Spot Monitoring (BSM)
Warning BeepThe Blind Spot Monitoring (BSM) or Rear Cross Traffic Alert (RCTA) system notifies the
driver of the presence of vehicles in adjacent lanes to the rear of your vehicle using the
Blind Spot Monitoring (BSM) warning lights and the warning beep while the systems are
operational.
Blind Spot Monitoring (BSM) warning lights
The Blind Spot Monitoring (BSM) warning lights are equipped on the left and right door
mirrors. The warning lights turn on when a vehicle approaching from the rear in an adjacent
lane is detected.
When the ignition is switched ON, the malfunction warning light turns on momentarily and
then turns off after a few seconds.
Forward driving (Blind Spot Monitoring (BSM) system operation)
The Blind Spot Monitoring (BSM) system detects vehicles approac hing from the rear and
turns on the Blind Spot Monitoring (BSM) warning lights equippe d on the door mirrors
according to the conditions. Additionally, while a Blind Spot Monitoring (BSM) warning
light is illuminated, if the turn signal lever is operated to signal a turn in the direction
in which the Blind Spot Monitoring (BSM) warning light is illum inated, the Blind Spot
Monitoring (BSM) warning light flashes.
MX-5_8FR4-EA-16J_Edition1.indb 88 2016/08/11 20:29:02

5 –13 Interior Features
Audio System
*Some models.AntennaAM/FM Radio Antenna
The AM/FM radio antenna receives both
AM and FM signals.
To remove the antenna, turn it
counterclockwise.
To install the antenna, turn it clockwise.
Make sure the antenna is securely
installed. Install
Rem ove
CAUTION To prevent damage to the antenna,
remove it before passing beneath a
low overhead clearance.
NOTE
When leaving your vehicle unattended, we
recommend that you remove the antenna
and store it inside the vehicle. Satellite Radio Antenna *
The satellite radio antenna receives
SiriusXM signals. Satellite radio antenna
MX-5_8FR4-EA-16J_Edition1.indb 13 2016/08/11 20:29:09

5 –16 Interior Features
Audio System Weak signal noise
In suburban areas, broadcast signals
become weak because of distance from the
transmitter. Reception in such fringe areas
is characterized by sound breakup.
Strong signal noise
This occurs very close to a transmitter
tower. The broadcast signals are extremely
strong, so the result is noise and sound
breakup at the radio receiver.
Station drift noise
When a vehicle reaches the area of two
strong stations broadcasting at similar
frequencies, the original station may be
temporarily lost and the second station
picked up. At this time there will be some
noise from this disturbance. Station 2
88.3 MHzStation 1
88.1 MHz Operating Tips for CD Player Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the CD or
optical components (prism and lens) in
the CD player may become clouded with
condensation. At this time, the CD will
eject immediately when placed in the unit.
A clouded CD can be corrected simply by
wiping it with a soft cloth. Clouded optical
components will clear naturally in about
an hour. Wait for normal operation to
return before attempting to use the unit.
Handling the CD player
The following precautions should be
observed. 
Do not use deformed or cracked CDs.
The disc may not eject resulting in a
malfunction. 
Do not use non-conventional discs such
as heart-shaped, octagonal discs, etc.
The disc may not eject resulting in a
malfunction.
MX-5_8FR4-EA-16J_Edition1.indb 16 2016/08/11 20:29:10