turn signal MAZDA MX5 MIATA 2017 Owner's Guide

7 –35 If Trouble Arises
Warning/Indicator Lights and Warning Sounds Signal Warning
(Red)
High Engine Coolant
Temperature Warning
Indication/Warning
Light The light flashes when the engine coolant temperature is extreme ly high, and
illuminates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine load until you can find a safe pla ce to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place
immediately and stop the engine.
Refer to Overheating 7-27 .
CAUTION Do not drive the vehicle with the high engine coolant temperature warning light
illuminated. Otherwise, it could result in damage to the engine.
Power Steering
Malfunction Indicator
Light The light illuminates if the electric power steering has a malfunction.
If the light illuminates, stop the vehicle in a safe place and do not operate the steering
wheel. There is no problem if the light turns off after a while. Contact an Authorized
Mazda Dealer if the light illuminates continuously.
NOTE 
If the indicator light illuminates, the power steering will not operate normally. If this
happens, the steering wheel can still be operated, however, the operation may feel
heavy compared to normal, or the steering wheel could vibrate when turning. 
Repeatedly jerking the steering wheel left and right while the vehicle is stopped or
moving extremely slowly will cause the power steering system to go into protective
mode which will make the steering feel heavy, but this does not indicate a problem. If
this occurs, park the vehicle safely and wait several minutes for the system to return
to normal.
MX-5_8FR4-EA-16J_Edition1.indb 35 2016/08/11 20:30:03

7 –36 If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models. Contact Authorized Mazda Dealer and Have Vehicle InspectedIf any of the following warning lights or the indicator light t urns on/flashes, the system may
have a malfunction. Contact an Authorized Mazda Dealer to have your vehicle inspected. Signal Warning
Master Warning
Indication/Warning
Light *
Type A instrument cluster
(Master warning indication)
Displays when notification of the system malfunctions is require d.
Check the message indicated in the display and consult an Authorized Mazda Dealer.
(Master warning light)
The master warning light displays when a warning message occurs.
This indicates a malfunction with the vehicle system. Check the message indicated in the
display and consult an Authorized Mazda Dealer.
For details, refer to the explanations for the warning/indicato r lights, in the warning/
indicator lights section, which match the symbol in the upper part of the display.
If a message is not indicated in the display, operate the INFO switch to display the
“Warning” screen.
Refer to Message Indicated in Multi-information Display and INF O switch on page 4-18 .
Type B instrument cluster
The light illuminates continuously if any one of the following occurs. Consult an
Authorized Mazda Dealer. 
There is a malfunction in the battery management system. 
There is a malfunction in the brake switch.
Electric Vacuum
Pump Warning
Light The light turns on if the electric vacuum pump system has a problem. Have your vehicle
inspected at an Authorized Mazda Dealer.
ABS Warning Light If the ABS warning light stays on while you're driving, the ABS control unit has detected a
system malfunction. If this occurs, your brakes will function normally as if the vehicle had
no ABS.
Should this happen, consult an Authorized Mazda Dealer as soon as possible.
NOTE 
When the engine is jump-started to charge the battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs, it is the result of the weak battery and does
not indicate an ABS malfunction.
Recharge the battery.

The brake assist system does not operate while the ABS warning light is illuminated.
Check Engine Light If this light illuminates while driving, the vehicle may have a problem. It is important to
note the driving conditions when the light illuminated and consult an Authorized Mazda
Dealer.
The check engine light may illuminate in the following cases: 
The engine's electrical system has a problem. 
The emission control system has a problem. 
The fuel tank level being very low or approaching empty. 
The fuel-filler cap is missing or not tightened securely.
If the check engine light remains on, or it flashes continuously , do not drive at high speeds
and consult an Authorized Mazda Dealer as soon as possible.
MX-5_8FR4-EA-16J_Edition1.indb 36 2016/08/11 20:30:03

7 –39 If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.Signal Warning
(Illuminate)
Lane Departure
Warning System
(LDWS) Warning
Indication/Warning
Light *

The warning indication/warning light illuminates if there is a problem with the system.
Have your vehicle inspected at an Authorized Mazda Dealer. 
The LDWS does not operate when the warning indication/warning light illuminates.
CAUTION 
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an Authorized Mazda Dealer.

When the warning indication/warning light illuminates while driving the vehicle.
When the system is canceled automatically, the warning indication/warning
light illuminates. Normally, the system restores automatically and the warning
indication/warning light turns off, however, if the warning indication/warning light
illuminates, there may be a problem with the system.

The warning indication/warning light does not illuminate when the ignition is
switched ON.

Always use tires for all wheels that are of the specified size, and the same
manufacture, brand, and tread pattern. In addition, do not use tires with significantly
different wear patterns on the same vehicle. If such improper tires are used, the LDWS
may not operate normally.

When an emergency spare tire is used, the system may not operate normally.
NOTE If the windshield area in front of the Forward Sensing Camera (FSC) is fogged or
obstructed, the light turns on temporarily. If the light remains turned on, there may be a
problem with the system.
(Amber)
High Beam Control
System (HBC)
Warning Indication/
Warning Light *
The warning indication/warning light illuminates if there is a problem with the system.
Have your vehicle inspected at an Authorized Mazda Dealer.
NOTE If the windshield area in front of the Forward Sensing Camera (FSC) is fogged or
obstructed, the warning indication/warning light illuminates temporarily. If the warning
indication/warning light illuminates, there may be a problem with the system.
Blind Spot
Monitoring (BSM)
Warning Indication *
The message is displayed when the system has a malfunction. Have your vehicle inspected
by an Authorized Mazda Dealer.
NOTE If the vehicle is driven on a road with less traffic and few vehicles that the radar sensors
can detect, the system may pause. However, it does not indicate a malfunction.
Blind Spot
Monitoring (BSM)
OFF Indicator
Light *
A problem in the system may be indicated under the following conditions.
Have your vehicle inspected at an Authorized Mazda Dealer. 
The light does not turn on when the ignition is switched ON. 
The light remains on even when the Blind Spot Monitoring (BSM) system can be operated.
The light turns on while driving the vehicle.
NOTE If the vehicle is driven on a road with less traffic and few vehicles that the radar sensors
can detect, the system may pause (The Blind Spot Monitoring (BSM) OFF indicator light in
the instrument cluster illuminates). However, it does not indicate a malfunction.
MX-5_8FR4-EA-16J_Edition1.indb 39 2016/08/11 20:30:04

7 –41 If Trouble Arises
Warning/Indicator Lights and Warning Sounds Taking ActionTake the appropriate action and verify that the warning light turns off. Signal Warning Action to be taken
Seat Belt Warning Light Except Mexico
The seat belt warning light turns on if the driver
or passenger's seat is occupied and the seat belt
is not fastened with the ignition switched ON.
If the driver or passenger's seat belt is
unfastened (only when the passenger's seat is
occupied) and the vehicle is driven at a speed
faster than about 20 km/h (12 mph), the warning
light flashes. After a short time, the warning
light stops flashing, but remains illuminated.
NOTE 
The warning light flashes for about 6 seconds
if the driver's seat belt is not fastened when the
ignition is switched ON. 
To allow the passenger occupant classification
sensor to function properly, do not place
and sit on an additional seat cushion on the
passenger's seat. The sensor may not function
properly because the additional seat cushion
could cause sensor interference. 
If a small child is seated on the passenger's
seat, the warning light may not operate.
Mexico
The seat belt warning light turns on if the driver
or passenger's seat is occupied and the seat belt
is not fastened with the ignition switched ON.
If the driver or passenger's seat belt is
unfastened (only when the passenger's seat is
occupied) and the vehicle is driven at a speed
faster than about 20 km/h (12 mph), the warning
light flashes. After a short time, the warning
light stops flashing, but remains illuminated. If
a seat belt remains unfastened, the warning light
flashes again for a given period of time.
NOTE 
Placing heavy items on the passenger's seat
may cause the passenger's seat belt warning
function to operate depending on the weight
of the item. 
To allow the passenger seat weight sensor to
function properly, do not place and sit on an
additional seat cushion on the passenger's
seat. The sensor may not function properly
because the additional seat cushion could
cause sensor interference. 
If a small child is seated on the passenger's
seat, the warning light may not operate. Fasten the seat belts.
MX-5_8FR4-EA-16J_Edition1.indb 41 2016/08/11 20:30:04

7 –42 If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.Signal Warning Action to be taken
Door-Ajar/Trunk
lid-Ajar Warning
Indication/Warning Light The light turns on if any door/trunk lid is
not closed securely. Close the door/trunk lid securely.
Low Fuel Warning Light The light turns on when the remaining fuel
is about 9.0 L (2.3 US gal, 1.9 Imp gal).
NOTE The light illumination timing may
vary because fuel inside the fuel tank
moves around according to the driving
conditions and the vehicle posture. Add fuel.
Check Fuel Cap Warning
Light If the check fuel cap warning light
illuminates while driving, the fuel-filler
cap may not be installed properly. Stop the engine and reinstall the fuel-filler
cap.
Refer to Fuel-Filler Cap on page 3-26
Low Washer Fluid Level
Warning Indication/
Warning Light *
This warning light indicates that little
washer fluid remains. Add washer fluid (page 6-31 ).
MX-5_8FR4-EA-16J_Edition1.indb 42 2016/08/11 20:30:04

7 –43 If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.Signal Warning Action to be taken
(Illuminate)
Tire Pressure Monitoring
System Warning Light *
When the warning light illuminates, and
the warning beep sound is heard (about 3
seconds), tire pressure is too low in one or
more tires.
WARNING If the tire pressure monitoring system
warning light illuminates or flashes,
or the tire pressure warning beep
sound is heard, decrease vehicle
speed immediately and avoid sudden
maneuvering and braking:
If the tire pressure monitoring system
warning light illuminates or flashes,
or the tire pressure warning beep
sound is heard, it is dangerous to
drive the vehicle at high speeds, or
perform sudden maneuvering or
braking. Vehicle drivability could
worsen and result in an accident.
To determine if you have a slow leak
or a flat, pull over to a safe position
where you can check the visual
condition of the tire and determine
if you have enough air to proceed to
a place where air may be added and
the system monitored again by an
Authorized Mazda Dealer or a tire
repair station.
Do not ignore the TPMS Warning Light:
Ignoring the TPMS warning light is
dangerous, even if you know why
it is illuminated. Have the problem
taken care of as soon as possible
before it develops into a more serious
situation that could lead to tire
failure and a dangerous accident. Inspect the tires and adjust to the specified
inflation pressure (page 6-41 ).
NOTE 
Perform tire pressure adjustment when
the tires are cold. Tire pressure will
vary according to the tire temperature,
therefore let the vehicle stand for 1
hour or only drive it 1.6 km (1 mile) or
less before adjusting the tire pressures.
When pressure is adjusted on hot tires
to the cold inflation pressure, the TPMS
warning light/beep may turn on after
the tires cool and pressure drops below
specification.
Also, an illuminated TPMS warning
light, resulting from the tire air
pressure dropping due to cold ambient
temperature will remain illuminated
even if the ambient temperature rises.
In this case, it will also be necessary to
adjust the tire air pressures. If the TPMS
warning light illuminates due to a drop
in tire air pressure, make sure to check
and adjust the tire air pressures. 
Tires lose air naturally over time and
the TPMS cannot tell if the tires are
getting too soft over time or you have
a flat. However, when you find one low
tire in a set of four-that is an indication
of trouble; you should have someone
drive the vehicle slowly forward so you
can inspect any low tire for cuts and any
metal objects sticking through tread or
sidewall. Put a few drops of water in the
valve stem to see if it bubbles indicating
a bad valve. Leaks need to be addressed
by more than simply reinflating the tire
as leaks are dangerous — take it to an
Authorized Mazda Dealer.
MX-5_8FR4-EA-16J_Edition1.indb 43 2016/08/11 20:30:05

7 –44 If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.KEY Indication (White)/KEY Warning Light (Red) *
Take the appropriate action and verify that the warning light turns off. Signal Cause Action to be taken
(White)
KEY Indication *
The advanced key battery is dead. Replace the key battery (page 6-38 ).
(Red)
(Flashing)
KEY Warning Light *
(Red)
(Flashing)
KEY Warning Light *
The advanced key is not within the
operation range.
Bring the advanced key into the operation
range (page 3-7 ).The advanced key is placed in areas inside
the cabin where it is difficult for the key to
be detected.
A key from another manufacturer similar to
the advanced key is in the operation range. Take the key from another manufacturer
similar to the advanced key out of the
operation range.
Without the ignition switched off, the
advanced key is taken out of the cabin, and
then all the doors are closed. Bring the advanced key back into the
cabin.
MX-5_8FR4-EA-16J_Edition1.indb 44 2016/08/11 20:30:05

7 –50 If Trouble Arises
Warning/Indicator Lights and Warning Sounds Key Removed from Vehicle
Warning BeepVehicles with advanced keyless function
If the key is taken out of the vehicle while
the ignition is not switched OFF and
all the doors are closed, the beep which
sounds outside of the vehicle will be heard
6 times, the beep which sounds inside
the vehicle will be heard 6 times, and the
KEY warning light (red) in the instrument
cluster flashes continuously to notify
the driver that the ignition has not been
switched OFF.
Vehicles without advanced keyless
function
If the key is taken out of the vehicle while
the ignition is not switched OFF and all
the doors are closed, a beep will be heard
in the cabin 6 times and the KEY warning
light (red) in the instrument cluster turns
on continuously to notify the driver that
the ignition has not been switched OFF.
NOTE
Because the key utilizes low-intensity
radio waves, the Key Removed From
Vehicle Warning may activate if the key is
carried together with a metal object or it
is placed in a poor signal reception area.
Request Switch Inoperable
Warning Beep (With the advanced
keyless function)
If the request switch is pressed with the
door open or ajar, or the ignition is not
switched OFF with a key being carried,
a beep will be heard outside for about 2
seconds to notify the driver that the door
or trunk lid cannot be locked. Key Left-in-trunk Warning Beep
(With the advanced keyless
function) If the key is left in the trunk with all the
doors locked and the trunk lid closed, a
beep will be heard outside for about 10
seconds to notify the driver that the key is
in the trunk. In this case, take out the key
by pressing the electric trunk lid opener
and opening the trunk lid. The key taken
out of the trunk may not operate because
its functions have been temporarily
stopped. To restore the key's functions,
perform the applicable procedure (page
3-7 ).
Key Left-in-vehicle Warning Beep
(With the advanced keyless
function) If all the doors and trunk are locked using
another key while the key is left in the
cabin, the beep which sounds outside of
the vehicle will be heard for about 10
seconds to notify the driver that the key
is in the cabin. In this case, take out the
key by opening the door. A key taken
out of the vehicle using this method may
not operate because its functions have
been temporarily stopped. To restore the
key's functions, perform the applicable
procedure (page 3-7 ).
Power Steering Warning Buzzer
If the power steering system has
a malfunction, the power steering
malfunction light turns on or flashes and
the buzzer operates at the same time.
Refer to Warning Indication/Warning
Lights on page 4-26 .
MX-5_8FR4-EA-16J_Edition1.indb 50 2016/08/11 20:30:07

7 –51 If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models. Tire Inflation Pressure Warning
Beep *
The warning beep sound will be heard
for about 3 seconds when there is any
abnormality in tire inflation pressures
(page 4-105 ).
Blind Spot Monitoring (BSM)
System Warning Beep *
Driving forward
The warning beep operates when the turn
signal lever is operated to the side where
the Blind Spot Monitoring (BSM) warning
light is illuminated.
NOTE
A personalized function is available to
change the Blind Spot Monitoring (BSM)
warning beep sound volume.
Refer to Personalization Features on page
9-9 .
Reversing
If a moving object such as a vehicle or
two-wheeled vehicle approaches on the
left or right from behind your vehicle, the
Blind Spot Monitoring (BSM) warning
sound is activated. Lane Departure Warning Sound *
While the system is operating, if the
system determines that the vehicle may
depart from the lane, it sounds a warning
sound. NOTE 
The volume of the LDWS warning sound
can be changed.
Refer to Personalization Features on
page 9-9 . 
The type of the LDWS warning sound
can be changed.
Refer to Personalization Features on
page 9-9 .
MX-5_8FR4-EA-16J_Edition1.indb 51 2016/08/11 20:30:07

9 –7 Specifications
Specifications Light BulbsExterior light Light bulb Category
Wattage UNECE *1
(SAE)
Headlights High beam LED *2
— (—)
Low beam LED *2
— (—)
Daytime running lights LED type LED *2
— (—)
Bulb type 21 W21W (7440)
Parking lights LED *2
— (—)
Front side-marker lights 5 W5W (—)
Front turn signal lights 28/8 — (7444NA)
Side turn signal lights 5 *3
WY5W (—)
High-mount brake light LED *2
— (—)
Rear turn signal lights 21 WY21W (7443NA)
Rear side-marker lights 5 W5W (—)
Brake lights LED *2
— (—)
Taillights LED *2
— (—)
Reverse lights 21 W21W (7440)
License plate lights 5 W5W (—)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
*3 Bulb replacement is not possible because it is built into the u nit. Replace the unit.
Interior light Light bulb Category
Wattage UNECE *1
Overhead light 10 —
Trunk light 5 —
*1 UNECE stands for United Nations Economic Commission for Europe.
MX-5_8FR4-EA-16J_Edition1.indb 7 2016/08/11 20:30:22