mirror MAZDA PROTEGE 1992 User Guide

WINDSHIELD S
1. Sun visor and adaptor 7. Glass stopper
2. Inside rearview mirror, overhead console 8. A-pillar garnish (Hatchback)
(With sliding sunroof) Removal / Installation . . . . . . . . . . . . . . . . . . page S-42
3. A-pillar trim 9. Upper windshield molding
Removal / Installation ..,.,..... pages S-97, 98 Removal / Installation . . . . . . . . . . . . . . . . . . page S-42
4. Upper garnish 10. Windshield
5. Wiper arm and blade Removal Note .,.....*.........*........... page S-59
Removal / Installation . . . . . . . . . . . . page S-72 Installation Note ..,......*................ page S-60
6. Cowl arille 11. Spacer
Removal I Installation . . . . . . . . . . . . page S-53 12. Protector
1 HEADLINER
Gsi?i==
SiX.A-A
03uosx-08
PROTECTIVE TAPE -I
9 03UOSX-088
Removal Note
Windshield
1, Use protective tape or cloth along the front edge of the head-
liner to protect it from damage.
2. Apply protective tape along the edge of the body.
3. Using an awl, make a hole through the sealant from the in-
side of the vehicle.
4. Pass piano wire through the hole.
5. Wind each end of the wire around a bar.
6. Working with another person, saw through the sealant
around the edge of the glass. Then remove the glass.
Caution
l Use a long sawing action to spread the work over
the whole length of wire to prevent if from breaking.
l Be careful that the wire does not rub on the body
or dash panel.
Note
l If the glass is not to be reused, a tool like that shown
in the figure may be used.
Insert the blade in the sealant, and pull on the bars.
s-59

SLIDING SUNROOF
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to Removal Note.
3. Install in the reverse order of removal, referring to Installation Note.
Note
l Remove the headliner for removal of the sunroof harness, sunroof relay, drive unit assembly,
and sunroof frame and
packing. (Refer to page S-89.)
SUNROOF (STEEL)
031JOSX.1,
1. Decoration cover (Moonroof) 7. Set plate 14. Motor assembly
Removal Note . . page S-84 Installation Installation
2. Lower panel cover (Moonroof) Note . . . . . . . . . . . . . . . page S-86 Note . . . . . . . . . . . . . . . page S-86
Removal Note . . page S-84 8. Guide rail cover Inspection
3. Sliding roof trim (Sunroof) Installation 15. Rear guide assembly
Removal Note . . page S-84 Note . . . . . . . . . . .
page S-86 Removal Note page S-86
4. Sliding panel assembly 9. Sunshade (Moonroof) Installation
Removal Note . page S-84 Removal Note . . page S-84 Note . . . . . . . . . . . . . page S-86
Adjustment 10. Deflector 16. Sliding roof harness
Note . . . . . . . . . . . . . page S-87 Removal Note . . page S-85 17. Sliding roof relay
a. Sliding panel 11. Lower panel Inspection.. . . . . . . page S-82
b. Glass (Moonroof) Removal Note ,. page S-85 18. Drive unit assembly
c. Weatherstrip 12. Front guide 19. Sliding roof frame
5. Rearview mirror 13. Drip rail assembly 20. Guide rail assembly
6. Overhead console 21. Packing
Inspection . . . . . . . . . page S-82
S-83

S HEADLINER
Y
PROTEGfi
(WITHOUT PASSIVE SHOULDER BELT)
1. Assist handle
2. Interior lamp
3. Seaming welt (With sliding
sunroof)
4. Sunvisor
IJ”“DA-“oC
5. Sunvisor adapter
9. Headliner
6. Rearview mirror Removal Note . . page S-93
7. Overhead console (With slid- Installation Note page S-93
ing sunroof)
IO. Front top bracket
8. Seaming welt (Pillar)
s-90

HEADLINER S
HATCHBACK
(WITH
PASSIVE SHOULDER BELT)
I
R.H. SIDE I
1. Assist handle 5. Rearview mirror
2. Interior lamp 6. Headliner
3. Sunvisor Removal Note .,.,,.,,.......*........,.*.* page S-93
4. Sunvisor adapter
Installation Note ..,.............*......... page S-93
s-91

s HEADLINER
HATCHBACK
(WITHOUT PASSIVE SHOULDER BELT)
R.H. SIDE
1. Assist handle
2. Interior lamp
3. Seaming welt (With sliding sunroof)
4. Sunvisor
5. Sunvisor adapter
6. Rearview mirror
13uosx-03
7. Overhead console (With sliding sunroof)
8. Seaming welt (Pillar)
9. Headliner
Removal Note ,..........,,,....,..,....... page S-93
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . . page S-93
10. Front top bracket ---
S-92

INDEX T
INSTRUMENT CLUSTER AND SWITCHES
23UOTX-00
1. Rear window defroster switch
7. Fuel gauge sender unit
Inspection
........................... page T-21 Removal / Installation ..................
page T-73
2. Remote control door mirror switch
Inspection ................................... page T-73
Inspection
........................... page T-20 8. Hazard warning switch
3. Ignition switch
Removal / installation .................. page T-20
Removal / Installation..
........ page T-20 Inspection ................................... page T-21
Inspection ........................... page
T-2 1 9. Cruise control main switch
4. Combination switch Inspection ...................................
page T-21
Removal / installation
.......... pages T-23, 25 10. Cruise control switch
Disassembly / Assembly ..... pages T-24, 26 Removal / Installation ..................
page T-20
Inspection
........................... pages T-27, 28 Inspection ................................... page T-21
5. Instrument cluster 11. Power window main switch
Troubleshooting..
................ page T-65 Inspection ................................... page T-22
Removal / Installation
.......... page T-69 12. Power window switch
Disassembly I Assembly ..... page T-70 Inspection ................................... page T-22
Inspection
........................... page T-71 13. Panel lamp control switch
6. Water thermosensor
Inspection ................................... page T-22
Removal / Installation..
........ page T-72
Inspection ........................... page T-72
T-3

SWITCHES T
SWITCHES
STRUCTURAL VIEW
13UOfX-0'
1. Rear window defroster switch 6. Power window main switch
Inspection . . . . #. . . . . . . . . . . . . . . ..,. . . . . . . . . . . . page T-21 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-22
2. Remote control door mirror switch
7. Power window switch
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-20 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-22
3. Ignition switch
8. Cruise control switch
Removal I Installation . . . . . . . . . . . . . . . . . . page T-20 Removal / Installation . . . . . . . . . . page T-20
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-21 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-21
4. Cruise control main switch 9. Combination switch
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-21 Removal / Installation . . . . . . . . . . pages T-23, 25
5. Hazard warning switch Disassem biy / Assembly . . . . . pages T-24, 26
Removal / Installation . . . . . . . . . . . . . . . . . . page T-20 Inspection ,...,.,.,.................. pages T-27, 28
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-21 10. Panel lamp control switch
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-22
T-l 9

T SWITCHES
03UOTX-026
H&N CAP
03UOTX-02 8
03UOTX-02s
SWITCH
Removal / Installation
Ignition switch
1. Remove the negative battery cable.
2. Remove the steering column cover.
3. Remove the screw and the ignition switch.
4. Install in the reverse order of removal.
Hazard warning switch
1. Remove the meter hood.
2. Remove the screws and the hazard switch.
3. Install in the reverse order of removal.
Cruise control switch
(set/coast and resume/accel switch)
1. Remove the steering wheel cap.
2. Remove the cruise control switch as shown in the figure.
3. Install in the reverse order of removal.
Inspection
1. Check for continuity between the terminals with an
ohmmeter.
Remote control door mirror switch
CLASS DIRECTION a b c d i k I
UP o---o
0 0
1 UP
I I lo! I-l7ol
o----O: Indicates continuity
T-20

.T INTERIOR LAMP SYSTEM
SPOT LAMP (IN OVERHEAD CONSOLE)
Removal / Inspection / Installation
1. Remove in the order shown in the figure.
2. lnsoect all parts and repair or replace as necessary.
3. Install in the reverse order of removal.
1. Rearview mirror
2. Cover
LENS
3. Lens
4. Bulb
Visual inspection
INTERIOR LAMP (WITHOUT SUNROOF)
Removal / Inspection / Installation
1. Remove the lens.
2. Remove the bulb.
3. Remove the screws and cover.
4. Inspect all parts and repair or replace as necessary.
5. Install in the reverse order of removal.
T-52

PARTS INDEX
‘I
A
ACCELERATOR CABLE ............................. F-l 14
ACCELERATOR PEDAL ............................. F-l 14
AIR CONDITIONER ...................................... u-30
A/C RELAY.. ........................................... U-56
A/C SWITCH ...........................................
U-57
COMPRESSOR.. ..................................... U-41
CONDENSER.. ....................................... U-53
CONDENSER FAN ................................. u-57
CONDENSER FAN RELAY .................... U-56
COOLING UNIT ..................................... U-38
MAGNETIC CLUTCH ............................. u-51
RECEIVER/DRIER .................................. U-52
REFRIGERANT PRESSURE SWITCH.. .. U-55
AIR FLOW METER ..................................... F-l 68
AIR VALVE.. ................................................ F-l 16
ALTERNATOR .............................................. G-10
ANTENNA FEEDER
AUDIO
....... .......................................................................................... T-i;
AUTOMATIC TRANSAXLE ............................. K-l
2-4 BRAKE BAND ................................ K-l 97
3-4 CLUTCH.. ....................................... K-l 87
ACCUMULATORS ................................ K-l 67
ATF ....................................................... K-135
ATF THERMOSENSOR ........................ K-142
BEARING COVER ASSEMBLY ............ K-208
CLUTCH ASSEMBLY ........................... K-l 72
CONTROL VALVE BODY.. .....
K-21 0,224,234
DIFFERENTIAL ..................................... K-236
DRIVE PLATE.. ..................................... K-267
EC-AT CONTROL UNIT ....................... K-144
HOLD SWITCH ..................................... K-140
HYDRAULIC CIRCUIT .......................... K-278
IDLER GEAR ........................................ K-203
INHIBITOR SWITCH ............................. K-l 41
LOW AND REVERSE BRAKE .............. K-192
MAIN CONTROL VALVE BODY .......... K-220
OIL COOLER.. ...................................... K-265
OIL PUMP ............................................
K-169
OIL SEAL ..............................................
K-209
ONE-WAY CLUTCH 2
CARRIER HUB ASSEMBLY ............... K-185
OUTPUT GEAR .................................... K-206
P RANGE SWITCH.. ............................. K-271
PREMAIN CONTROL VALVE BODY .a. K-218
PULSE GENERATOR ........................... K-142
SELECTOR LEVER ............................... K-272
SHIFT MECHANISM ............................. K-269
SHIFT-LOCK ACTUATOR
..................... K-271
SMALL SUN GEAR AND
ONE-WAY CLUTCH 1 ........................ K-l 82
SOLENOID VALVE.. ............................. K-l 43
SPEEDSENSOR .................................. K-l 43
THROTTLE CABLE .............................. K-l 37
TORQlJE CONVERTER.. ...................... K-l 66
TRANSAXLE UNIT. ......... K-149,153,246,261 UPPER CONTROL VALVE BODY.. ..... K-215
BACK-UP LIGHT SWITCH..
..........................
BATTERY T;4;
- .......................................................
BLOWER UNIT ............................................
U-23
BRAKE FLUID.. .............................................. P-8
BRAKE MASTER CYLINDER. ...................... P-10
BRAKE PEDAL ...............................................
P-8
C
CALIPER .................................................. P-21,26
CARGO COMPARTMENT LAMP ................. T-54
CENTRAL PROCESSING UNIT..
.................. T-55
CHARCOAL CANISTER ............................. F-l 41
CHECK VALVE (TWO-WAY) .......................
CHECK-AND-CUT VALVE - .......................... ;-;b$
CIRCUIT OPENING RELAY.. ...................... F-129
CLUTCH COVER ......................................... H-l 7
CLUTCH DISC ............................................. H-l 7
CLUTCH FLUID ............................................. H-4
CLUTCH MASTER CYLINDER.. .................... H-7
CLUTCH PEDAL ............................................ H-5
CLUTCH RELEASE CYLINDER..
................. H-12
CLUTCH SWITCH (MTX) ............................ F-l 72
COMBINATION SWITCH .............................. T-23
COWL GRILLE ............................................. S-53
CRUISE CONTROL UNIT.. ...................... T-78,85
D
DASHBOARD ............................................... S-94
DASHPOT ................................................... F-l 42
DISTRIBUTOR .............................................. G-20
DOOR LOCK TIMER UNIT ........................... T-17
DOOR MIRROR ............................................ S-54
REMOTE CONTROL MIRROR ............... S-56
REMOTE CONTROL MIRROR SWITCH. S-55
DOOR SPEAKER .......................................... T-98
DRIVE SHAFT.. ....................................... M-l 7,21
DRL RELAY.. ................................................ T-18
DRL RESISTOR ............................................ T-46
DUAL PROPORTIONING VALVE..
............... P-l 6
DYNAMIC CHAMBER ................................ F-l 12
E
ELECTRIC COOLING FAN SYSTEM ........... E-13
ENGINE (B6 & BP SOHC) ........................... Bl-2
CAMSHAFT ..........................................
Bl-58
CAMSHAFT PULLEY ...........................
Bl-65
CONNECTING ROD ............................. 81-63
PI-I