battery MAZDA PROTEGE 1992 Owner's Manual

ON-VEHICLE MAINTENANCE
DEFLECTION CHECKING POINT
05UOBX-03 3 10. Measure the timing belt deflection by applying moderate
pressure (98 N, 10 kg, 22 lb) midway between the two cam-
shaft pulleys.
If the deflection is not correct, repeat from Step 7 above.
Deflection:
9.0-11.5mm (0.35-0.45 in) at 98 N (10 kg, 22 lb)
Harness
1. Connect the harness connectors. (Refer to page 82-l 8.)
Hose
1. Connect the hoses. (Refer to page 82-17.)
03UOB2-035
Accelerator cable
1. Install the accelerator cable.
2. Check the accelerator cable deflection.
If the deflection is not correct, adjust by turning nut A.
Deflection: l-3mm (0.04-0.12 In)
Steps After Installation
1. Fill the radiator with the specified amount and type of engine coolant. (Refer to Section E.)
2. Connect the negative battery cable.
3. Start the engine and check as follows:
(1) Engine oil and engine coolant leakage.
(2) Ignition timing, idle speed. (Refer to page B2-8.)
(3) Operation of emission control system.
4. Recheck the engine coolant levels.
2311082-022
B2-21

B2 ON-VEHICLE MAINTENANCE
HLA
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. install in the reverse order of removal, referring to Installation Note --- ----- -__ __-- ,‘.
11.3-14.2 N.m
(1.15-1.45 m-\g, 100-126 in-lb)
49-61
(5.0~6.2,-36-45)
4.9-6.6 N.m
(50-90 cm-kg, 43-76 in-lb)
7.6All N-m
(80-110 cm-kg, 69-95 in-lb) 1 Q’-25
(1.9-2.6, 14-19)
N.m (m-kg, ft-lb)
0311082-03
1. High-tension lead
10. Cylinder head cover
2. Distributor
Installation Note..
....................
Installation Note.. ......................
page 62-25
11. Camshaft pulley
3. P/S and/or A/C drive belt
Removal note ..........................
Removal / Installation..
.............. page E32-
6
Installation Note .......................
4. Alternator drive belt
12. Seal plate
Removal / Installation
......... . ...... page B2- 6
13. Camshaft
5. Water pump pulley
Removal Note.. ........................
6. Timing belt cover, upper
Installation Note.. .....................
7. Timing belt cover, middle
14. HLA
8. Spark plug
Removal note ..........................
9. Timing belt
Installation
Note.. .....................
Removal Note.. .........................
page B2-18 Inspection
................................
Installation Note.. ......................
page B2-20
7
page 62-19
page 82-23
page 82-24
page B2-23
page 62-23
page B2-23
page B2-23 ‘--’
page 82-60
82-22

ON-VEHICLE MAINTENANCE B2
05UOBX-05
BLA-DE 0-dlNG
Steps After Installation
1. Connect the negative battery cable.
2. Start the engine and check as follows:
l Ignition timing. (Refer to page 82-8.) 3. Install the camshaft pulley lock bolts.
4. Hold the camshaft with a wrench.
5. Tighten the camshaft pulley lock bolt.
Tightening torque:
49-61 N-m (5.0-6.2 m-kg, 36-45 ft-lb)
Distributor
1. Apply grease to a new O-ring and the blade.
2. Install the distributor and loosely tighten the installation bolt.
3. Connect the distributor connector.
0311082-039
B2-25

B2 ON-VEHICLE MAINTENANCE
FRONT OIL SEAL
Replacement
1. Disconnect the negative battery cable.
2. Raise the vehicle on a lift and remove the right front wheel.
3. Remove in the order shown in the figure, referring to
Removal Note.
4. Install in the reverse order of removal, referring to Installation Note.
I

@Em
157-167 (16-17, 116-123)
N.m (m-kg, ft-lb
1. Timing belt related parts.. ............ page B2-12
2. Pulley lock bolt
Removal Note ..................................... below
Installation Note.. page B2-27 ......................
3. Pulley boss
4. Timing belt
Removal Note.. ......................... page B2-13
Installation Note ........................ page B2-14 5. Timing belt pulley
Installation Note..
...................... page B2-27
6. Oil seal
Removal Note.. ......................... page B2-27
Installation Note.. ...................... page B2-27
Removal Note
Pulley lock bolt
1. Hold the pulley boss with the SST.
2. Loosen and remove the pulley lock bolt.

ON-VEHICLE MAINTENANCE
I 05UOBX-063
Oil seal
1. Cut the oil seal lip with a razor knife.
2. Remove the oil seal with a screwdriver protected with a rag.
13EOB2-02
ALIGN.KEY GRCi&E
13EOB2-02
23UOB2-025
Steps After Installation
1. Connect the negative battery cable.
2. Start the engine and check as follows:
l Ignition timing. (Refer to page 92-8.)
3
Installation Note
Oil seal
1. Apply a small amount of clean engine oil to the lip of a new
oil seal.
2. Push the oil seal slightly in by hand.
3. Tap the oil seal in evenly with a suitable pipe and a ham-
mer until it is about flush with the face of the oil pump body.
Oil seal outer diameter: 50.5mm (1.98 in)
Timing belt pulley
1. Install the timing belt pulley.
2. Install the pulley Woodruff key with the tapered side toward
the oil pump body.
Pulley lock bolt
1. Hold the crankshaft with the SST and tighten the pulley lock
bolt.
Tightening torque:
157-187 N.m (18-17 m-kg, 116-123 ft-lb)
23UOB2-026
82-27

B2 ON-VEHICLE MAINTENANCE
REAR OIL SEAL
Replacement
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. install in the reverse order of removal, referring to Installation Note.
t
I 1
ITX 16-26 (1.6-2.7, 13-20)

L
\TX
N.m (m-kg, ft-It 0
23UOBZ-027
1. Transaxle
MTX
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section J2
ATX
Service . . . , . . . . ,.......................... Section K
2. Clutch cover, clutch disc (MTX)
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section H
3. Flywheel (MTX)
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . below
Installation Note .,.....,..,............. page 82-29 4. Drive plate (ATX)
Removal Note ..,........................ page B2-29
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page 62-30
5. Oil seal
Removal Note .,......................... page 52-29
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page B2-29
23UOB2-05
82-28
il
Removal note
Flywheel (MTX)
1. Hold the flywheel with the SST or equivalent.
2. Remove the flywheel lock bolts.
3. Remove the flywheel.

B2 ON-VEHICLE MAINTENANCE
0311082-04
23UOB2-05 4
Drive plate (ATX)
1. Remove the sealant from the drive plate holes in the crank-
shaft and from the drive plate lock bolts.
Caution
..i
l if ail the previous sealant cannot be removed from
a bolt, replace the bolt.
l Do not apply sealant if a new bolt is used.
2. Set the adapter, drive plate, and backing plate onto the
crankshaft,
3. Apply sealant to the drive plate bolts and install them.
4. Hold the drive plate with the
SST or equivalent.
5. Tighten the bolts in two or three steps in the order shown
in the figure.
Tightening torque:
96-103 N-m (9.6-10.6 m-kg, 71-76 ft-lb)
Steps After installation
1. Connect the negative battery cable.
2. Start the engine and perform engine adjustments as necessary.
OWOBX-072
82-30

REMOVAL
REMOVAL
Warning
l Release the fuel pressure. (Refer to Section F.)
PROCEDURE
1. Disconnect the negative battery cable.
2. Drain the engine coolant and transaxle oil,.
3. Remove in the order shown in the figure, referring to
Removal Note.
Step
1
1. Undercover and side cover 12. Oil cooler hose (ATX)
2. Resonance chamber 13. Cooling fan connector
3. Air cleaner assembly 14. Radiator switch connector (ATX)
4. Battery bracket 15. Radiator bracket
5. Battery cover 16. Radiator and cooling fan assembly
6. Battery
17. P/S and/or A/C drive belt
7. Battery carrier Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page B2- 6
8. Battery duct 18. P/S oil pump and bracket
9. Accelerator cable Removal Note . . . . . . . . . . . . . . . . . . . . + . . . . . . page 82-32
10. Radiator hose 19. A/C compressor (if equipped)
11. Coolant reservoir hose Removal Note.. . . . . . . . . . . . . . . . . . . . . . . . . . page 82-32
B2-31

92 INSTALLATION
RESOiANCE CHAMBER
03UOBZ-154
Accelerator cable
1. Install the accelerator cable.
2. Adjust the cable deflection by turning nut A.
Deflection: 1-3mm (0.04-0.12 in)
Battery duct, battery carrier, and battery
1. Install the battery duct.
Tightening torque:
7.8-l 1 Nlm (80-l 10 cm-kg, 69-96 In-lb)
2. Install the battery carrier.
Tightening torque:
7.8-l 1 N*m (80-l 10 cm-kg, 69-96 in-lb)
3. Install the battery and the battery bracket.
Tightening torque:
2.9-5.9 N*m (30-60 cm-kg, 26-52 in-lb)
Air cleaner assembly
1. Install the air cleaner assembly.
Tightening torque
@: 19-25 N#m (1.9-2.6 m-kg, 14-19 ft-lb)
@: 7.8-l 1 N*m (80-l 10 cm-kg, 69-95 In-lb)
2. Connect the air flow sensor connector.
Resonance chamber
I, Install the resonance chamber.
Tightening torque:
7.8-l 1 N#m (80-l 10 cm-kg, 69-95 In-lb)
Under cover and side cover
1. Install the under cover and side cover.
Steps After Installation
1. If the engine oil was drained, fill with the specified amount and type of engine oil.
(Refer to Section D.)
2. Fill the radiator with the specified amount and type of engine coolant.
(Refer to Section E.)
3. If the transaxle oil was drained, fill with the specified amount and type of transaxle oil.
(Refer to Sections J2, K.)
4. Connect the negative battery cable.
5. Start the engine and check the following:
(1) Engine oil, transaxle oil, and engine coolant leakage.
(2) ignition timing, idle speed. (Refer to page 82-8.)
(3) Operation of emission control system.
6. Perform a road test.
7. Recheck the engine oil and engine coolant levels.
B2-102
2311082.047

OIL PAN
OIL PAN
REMOVAL / INSTALLATION
1. Disconnect the negative battery cable.
2. Drain the engine oil.
3. Remove the under cover and side cover.
4. Remove in the order shown in the figure, referring to
Removal Note.
5. Install in the reverse order of removal, referring to Installation Note.
B6 SOHC
37-52 (3.8-5.3, 27-38)
I
GASKET,
REPLACE
9-94 (7.0-9.6, 51-69)
-52 ,a m-c .a .Y’)-*II
29-41 (3.0--/.2, 22-30)
_- ,r.rr--r-u, -.--““I ‘.8 11 Nm 4,
#O-r 10 cm-k% 69-96 in-lb) ,a&
7.8-l 1 N.m (SO-1 10 cm-kg, 69-96 in-lb)
1. Front exhaust pipe and bracket
2. Integrated stiffener
3. Oil pan
Removal Note ,...*..,,..*..,..*.......... page D-10
Inspect for cracks, deformation or damage
installation Note .,,.,..,,,.,.,......,.... Page D-l 1 4. Oil strainer
5. Main bearing support plate (MBSP)
Removal Note ,..,..I.,.......,........... page D-l 1
Installation Note .,..,,.,.....,,.....,..,.. page D-l 1
D-9