window MAZDA PROTEGE 1992 Owner's Manual

POWER WINDOW SYSTEM S
POWER WINDOW SYSTEM
STRUCTURAL VIEW
1, Main power window switch
Inspection ................................... page S-31
2. Power window sub-switch (Passenger side)
Inspection ................................... page S-32
3. Power window sub-switch (Rear)
Removal / Installation .................. page S-l 7
Inspection ................................... page S-32
I i)V”Jh-““I
4. Power window regulator (Front door)
Removal / Installation
Hatchback ................................ page S-10
PROTEGE.. ............................... page S-l 1
Inspection ................................... page S-32
5. Power window regulator (Rear door)
Removal / Installation .................. page S-l 7
Inspection ................................... page S-32
s-27

l POWER WINDOW K-l
MAIN
PUWER WIWCW WWER WihJOW
-/w Y/W a/c x

POWER WINDOW SYSTEM S
Power window system does not operate
(All doors)
I
NG
Check POWER WIND 30A fuse - Repair harness and replace fuse
I
1 OK
Turn ignition switch ON
Check for battery voltage at terminal-wire (B/W) of main NG
power window switch connector Repair harness (Fuse box-Main power window switch)
I
OK
Disconnect main power window switch connector;
check continuity of terminal-wire (B) to ground Repair harness (Main switch-Ground)
OK
- Check main power window switch (Refer to page S-31)
I I
23UOSX-010
Only driver side power window does not operate
( Turn ignition switch ON
Check for battery voltage at terminal-wires (R/B) and
(R/G) of main power window switch connector
UP
DOWN (R/G) wire
~ _ 1 NG -i VB: Battst’y VOltaQe,
Check main power wrndow switch (Refer to page S-31)
OK
Check for battery voltage at terminal-wires (R/B) and
(R/G) of power window motor connector OK
= Check power window motor (Refer to page S-32)
23UOSX-011
Sk29

POWER WINDOW SYSTEM
II
Power window (except driver side) cannot be
operated by main switch
t
Turn ignition switch ON Note l Use only main switch during checking operation.
t
Check for battery voltage at terminal-wires of main
power window switch connector
Switch Condition
Passenger UP
side
DOWN
Rear (LH) . UP
DOWN
Rear (RH) UP
DOWN Terminal Voltage
(G/W) wire Ve
(R/W) wire VB
(G/Y) wire VB
(W/R) wire VB
(L/W) wire VB
(Y/W) wire Ve
I OK
Check for battery voltage at terminal-wires of power
window sub-switch connector while operating main
switch
VB: Battery voltage
NO
- Check main power window switch (Refer to page S-31) NG
___) Repair harness
(Main power window switch-Power window sub-switch)
I OK
Check for battery voltage at terminal-wires of power
window sub-switch connector while operating main
switch
Condition Terminal
UP (R) wire VB
DOWN (G) wire VB
I Check power window sub-switch (Refer to page S-32)
1 OK
Check for battery voltage at terminal wires of power
window motor connector while operating main switch
Condition Terminal Voltage
UP (R) wire
DOWN (G) wire OK
Check power window motor (Refer to page S-32) I 23uosx-012
s-30

POWER WINDOW SYSTEM
Main power window switch operates, but switch
on each door does not operate power window
I Turn ignition switch ON , !
Turn main power window switch ON
Check for battery voltage at terminal-wire (B/L) of main NG _ Check power switch of main power window switch
power window switch connector (Refer to page S-31) OK
Check for battery voltage at terminal-wire (B/L) of switch 3 Repair harness
on each door (Main power window switch-Power window sub-switch) OK
Check power window sub-switch (Refer to page S-32)
23UOSX-013
I PROTEGli HATCHBACK
I
ace
i k
MAIN POWER WINDOW SWITCH
Inspection
Check for continuity between terminals of the switch with an
ohmmeter.
Power switch (ON/OFF)
ON
nl=l= PROTEGE Hatchback
a f h
9
0 0 0 0
0--O: Indicates continuity
Power window switch (Up/Down)
UP ------ o-j0 - -
o-o 00 00
OFF 000 oojo 000 000
I DOWN
0---O: Indicates continuity
s-31

S POWER WINDOW SYSTEM
CD 0 0
L 23UOSX-014
03uosx-04
REAR
POWER WINDOW SUB-SWITCH
Inspection
Check for continuity between terminals of the switch with an
ohmmeter.
Passenger side
-
UP 0 0
0 0
--- -c
I 0
IOWN -,
o---O: indicates continuity
Rear
H: Indicates continuity
POWER WINDOW MOTOR (In power window regulator)
Inspection
1. Disconnect the power window motor connector.
2. Connect battery voltage to terminal (a) and ground termi-
nal (b) of the motor connector, and verify that the motor -I
operates.
3. Reverse the above connections and check for reverse oper-
ation of the motor.
23UOSX-015
S-32

MOLDING, PROTECTOR, GARNISH S
REAR WINDOW MOLDING (PROTEGE)
Removal / Installation
1. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
I A
I B 1 I
1. R.H. rear window molding
(with upper and lower joints)
2. L.H. rear window molding
(with upper and lower joints) 3. Upper rear window molding
s-43

S MOLDING, PROTECTOR, GARNISH
REAR WINDOW MOLDING (HATCHBACK)
Removal
Remove in the order show in the figure.
I
^^, .^^.. __-
1. Rear hatch lower trim
Removal . . . . . . . . . . . . . . . . . . . . . . . . ,.. . . . . . . . . . . , 4. L.H. rear window molding
page S-98
2. Lower rear window molding installation nuts
3. R.H. rear window molding
(with upper and lower joints)
s-44
(with upper and lower joints)
5. Lower rear window molding
6. Upper rear window molding

MOLDING, PROTECTOR, GARNISH
installation
Install in the order shown in the figure.
____------.-
- _-.-
S
03UOSX-06(
1. Lower rear window molding
2. R.H. rear window molding
(with upper and lower joints)
3. L.H. rear window molding
(with upper and lower joints) 4. Upper rear window molding
5. Lower rear window molding installation nuts
6. Rear hatch lower trim
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page
S-98
s-45

S WINDSHIELD
WINDSHIELD
PREPARATION
SST
49 0305 870A I 1 For
Tool set, window removal and
installation of
windshield
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. Install in the reverse order of removal, referring to Installation Note.
PROTEGC