window MAZDA PROTEGE 1992 Owner's Guide

WINDSHIELD S
PROTECTOR
I SEALANT
mm (in)
.
03uosx-09
GLASS /
SPACER
mm (in
03uosx-1c
PROTEG6
MOLDING MOLDING
SEALANT SEALANT
CROSS-SECTION
mm (in)
03uosx-1c
7. Align the protector on the body, and attach it securely as
shown.
8. Prepare the nozzle of the sealant gun so that it has a flange
that can run along the edge of the glass and a V from which
the sealant can flow. Once the primer is dry, apply the seal-
ant around the entire circumference of the glass to fill the
gap between the dam and the edge of the glass with a ridge
of sealant
12mm (0.47 in) high.
Keep the bead of sealant smooth and even, reshaping it
where necessary with a spatula.
9. Lift the glass into place. Push it in lightly toward the vehicle
to compress the sealant.
Caution
l Open the windows to prevent the glass from being
pushed out by air pressure if a door is closed.
Hardening time of repair seal
I Temperature Surface hardening Time required until car
time can be put into service
I
5% (41 OF) Approx. 1.5 hrs 12 hrs
2ooc (68OF) Approx. 1 hr
4 hrs
35OC (95OF)
Approx. 10 min 2 hrs
10. Align the upper windshield molding on the body as shown,
and push the molding into place along the top.
Note
l Install the molding before the sealant has hardened.
11. Check for water leaks. If a leak is found, wipe the water off
well and add
sealant (BOO1 77 739) where needed.
S-61

QUARTER WINDOW GLASS
QUARTER WINDOW GLASS
COMPONENTS
Removal / Installation
1, Remove in the order shown in the figure.
2. Install in the reverse order of removal.
Note
l Remove overlapping portion of the quarter trim for removal of the A-pillar trim (U.S.) or B-
pillar upper trim (Canada).
7.8-l 1 N.m (80-I 10 cm-kg, 69-95 in-lb)
9
1. Seat belt upper anchor (Canada) 3. Quarter window lock
Removal / Installation . . . . . . . . . . . . . . . . page S-100 4. Quarter window glass
2. A-pillar trim (U.S.)/B-pillar upper trim (Canada) 5. Quarter window hinge
Removal I Installation . . . . . . . . . . . . . . . . page S- 98 6. Pillar molding
S-62

REAR WINDOW GLASS S
REAR WINDOW GLASS
PREPARATION
SST
49 0305 870A
1 For
Tool set, window removal and
installation of rear
window glass
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. install in the reverse order of removal, referring to Installation Note.
r
I’
PROTEGi:
1. Rear seat cushion
6. Rear header trim
5
Removal I Installation . . . . . . . . . . . . . . . . page S-l 11
Removal / Installation . . . . . . . . . . . . . . . . page S-
97
2. Rear seat back/side
7. C-pillar trim
Removal I Installation . . . . . . . . . . . . . . . . page S-l 11
3. High-mount stoplight (interior mounted)
Removal / Installation . . . . . . . . . . . . . . . . . . . . . Section
T
4. Rear package trim
Removal I Installation . . . . . . . . . . . . . . . . page S-
97
5. Rear seat belt upper anchor
Removal / Installation ..,............. page
S-101
Removal / Installation . . . . . . . . . . . . . . . . page S-
97
8. Rear window molding
Removal I Installation . . . . . . . . . . . . . . . . page S-
43
9. Rear window glass
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . .
page S- 64
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page S-
65
10. Spacer
S-63

S REAR WINDOW GLASS
HATCHBACK
1
J
03UOSX-106
1. Rear wiper arm and blade
Removal / Installation . . . . . . . . . . . . . . . . . . page S-78
2. Rear window molding
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-44
Installation . . . . .,...,........................ page S-45
3. Rear hatch lower trim 4. Seaming welt
5. Rear window glass
Removal Note ..,.,,,.......,.............. page S-64
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . . page S-65
6. Spacer ‘.-
Removal / Installation . . . . . . . . . . . . . . . . page S-98
Removal Note
PROTECTIVE TAPE Rear window glass
1. Apply protective tape along the edge of the body to pro-
tect it from damage.
2. Using an awl, make a hole through the sealant from the in-
side of the vehicle.
3. Pass piano wire through the hole.
4. Wind each end of the wire around a bar.
5. Working with another person, saw through the sealant
around the edge of the glass. Then remove the glass.
Caution
l Use a long sawing action to spread the work over
the whole length of wire to prevent it from breaking.
l Be careful that the wire does not rub on the body.
I SMUOSX-139

REAR WINDOW GLASS S
9MUOSX-09
Note
l If the glass is not to be reused, a tool like that shown
in the figure may be used.
Insert the blade in the sealant, and pull on the bars.
Installation Note
Rear window glass
1. Cut away the old sealant with a razor knife so that 1 to 2mm
(0.04 to 0.08 in) of sealant remains around the circumfer-
ence of the frame. If all the sealant has come off in any one
place, apply primer after degreasing, and allow it
approx.
30 minutes
to dry. Then put on new sealant to create a
2mm (0.08 in) layer.
2. Carefully clean an area 5
cm (1.97 in) wide around the cir-
cumference of the glass and the bond on the body.
3. Bond a new dam along the circumference of the glass
7mm
(0.28 in) from the edge.
Caution
l Bond the dam securely and allow it to dry.
4. Apply primer with a brush to the bonding area of the glass
and the body, and allow it to dry for
approx. 30 minutes.
Caution
l Keep the area free of dirt and grease. Do not touch
the surface. If primer gets on the hands, remove it
immediately.
5. Install the spacers onto the body.
Caution
l Damaged spacers must be replaced.
S-65

S REAR WINDOW GLASS
03uosx-11
WOTEGk GLASS
SPACER
-lATCHBACk
GLASS
SPACER
mm (in
03uosx-11
6. Prepare the nozzle of the sealant gun so that it has a flange
that can run along the edge of the glass and a V from which
the sealant can flow. Once the primer is dry, apply the seal-
ant around the entire circumference of the glass to fill the
gap between the dam and the edge of the glass with a ridge
of sealant
12mm (0.47 in) high.
Keep the bead of sealant smooth and even, reshaping it
where necessary with a spatula.
7. Lift the glass into place. Push it in lightly toward the vehicle
to compress the sealant.
Caution
l Open the windows to prevent the glass from being
pushed out by air pressure if a door is closed.
Hardening time of repair seal
Temperature Surface hardening Time required until car
time can be put into service
5T (41 OF) Approx. 1.5 hrs 12 hrs
2o”c (6WF) Approx. 1 hr 4 hrs
35% (95OF) Approx. 10 min 2 hrs
8. Use a scraper to smooth away any sealant that oozes out.
Add more sealant to any points of poor contact.
9. Check for water leaks. If a leak is found, wipe the water off
well and add
sealant (BOO1 77 739) where needed.
S-66

REAR WIPER AND WASHER S
Wiper
Washer
1. Rear hatch lower trim
7. Trunk end trim
Removal / Installation . . . . . . . . . . . . . . . . page S-
98 Removal / Installation . . . . . . . . . . . . . . . . page
S- 98
2. Wiper arm cover 8. Trunk side cover
3. Rear wiper arm and blade Removal / Installation . . . . . . . . . . . . . . . . page S-
98
Adjustment
Note . . . . . . . . . . . . . . . . . . . . . . . page S- 79 9. Trunk side trim
4. Seal cap Removal / Installation . . . . . . . . . . . . . . . . page S-
98
5. Outer bushing 10. Rear header trim
6. Rear wiper motor Removal / Installation . . . . . . . . . . . . . . . . page S- 98
Inspection .,, ., . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page S- 77 11. Rear seat belt upper anchor
Removal / Installation . . . . . . . . . . . . . . . . page S-l 01
12. C-pillar trim
Removal / Installation . . . . . . . . . . . . . . . . page S-
98
13. Washer tank assembly
a. Washer tank
b. Washer motor
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page S- 77
14. Washer nozzle
Adjustment Note . . . . . . . . . . . . . . . . . . . . . . . page S-
79
15. Washer pipe
23UOSX-032
REAR WINDOW MOLDING
mm (in)
03uosx-14
REAR WINDQW MOLDING I
mm (in
03uosx-14
Adjustment Note
Arm height
1. Set the motor shaft to the park position by turning the rear
wiper switch from ON to OFF.
2. Set the arm height as shown in the figure.
Tightening torque:
5.9-9.8 N*m (80-100 cm-kg, 52-87 in-lb)
Washer nozzle
Inset-t a needle or similar object into the nozzle hole and move
the nozzle to adjust the spray direction.
s-79

S TRIM
Note (Hatchback)
l Remove the front seat belt upper anchor for removal of the B-pillar upper trim.
(Refer to page S-100.)
l Remove the rear seat belt upper anchor and the quarter window lock for removal of the C-
pillar trim. (Refer to pages S-62, 101.)
l Remove the rear seat cushion for removal of the quarter trim. (Refer to page S-112.)
* Disconnect the negative battery cable for removal of the rear hatch lower trim. (With luggage
compartment lamp.)
iATCHBACK
'. .' LA I i-i I / '.
1. Front side trim 7. Quarter trim
2. Scuff plate 8. B-pillar upper trim
3. Front door trim (Without passive shoulder belt)
Removal I Installation . . . . . . . . . . page S-l 0 9. A-pillar trim
4. Trunk end trim 10. Rear header trim
5. Trunk side cover 11. C-pillar trim
6. Trunk side trim 12. Rear hatch lower trim
S-98

BODY ELECTRICAL SYSTEM
INDEX .......................................... T- 2
RELAY ....................................... T- 2
INSTRUMENT CLUSTER AND
SWITCHES ................................ T- 3
EXTERIOR LIGHTS.. ..................... T- 4
INTERIOR LAMPS.. ...................... T- 5
CRUISE CONTROL SYSTEM.. ........ T- 6
AUDIO ....................................... T- 7
OTHER ...................................... T- 8
OUTLINE ...................................... T- 9
HOW TO USE THIS SECTION.. ...... T- 9
ELECTRICAL TROUBLESHOOTING
TOOLS .....................................
ELECTRICAL SYMBOLS - ............... T- 1x
TROUBLESHOOTING GUIDE.. .........
T- 11
FUSE AND JOINT BOX ..................
T- 12
STRUCTURAL VIEW.. ...................
T- 12
FUSES ....................................... T- 13
CIRCUIT BREAKER.. ....................
T- 14
JOINT BOX ................................. T- 15
RELAY .......................................... T- 16
STRUCTURAL VIEW.. ...................
T- 16
.-
FLASHER UNIT ........................... T- 17
DOOR LOCK TIMER UNIT ............
T- 17
HORN RELAY ............................. T- 18
HEADLIGHT RELAY.. ................... T- 18
TNS RELAY ................................ T- 18
DRL RELAY (CANADA). ................ T- 18
SWITCHES .................................... T- 19
STRUCTURAL VIEW.. ................... T- 19
SWITCH ..................................... T- 20
COMBINATION SWITCH ...............
T- 23
EXTERIOR LIGHTING SYSTEM ....... T- 29
STRUCTURAL VIEW.. ...................
T- 29
AIMING ...................................... T- 30
TROUBLESHOOTING.. .................
T- 30
HEADLIGHT AND FRONT
COMBINATION LIGHT.. ..............
T- 41
REAR COMBINATION LIGHT.. ....... T- 43
HIGH-MOUNT STOPLIGHT.. .......... T- 45
DRL RESISTOR ........................... T- 46
STOPLIGHT SWITCH.. .................. T- 47
BACK-UP LIGHT SWITCH ............. T- 47
LICENSE PLATE LIGHT.. ..............
T- 47
REAR SIDE MARKER LIGHT ......... T- 48
INTERIOR LAMP SYSTEM ..............
T- 49
STRUCTURAL VIEW.. ...................
T- 49
TROUBLESHOOTING ...................
T- 50 SPOT LAMP
(IN OVERHEAD CONSOLE) ......... T- 52
INTERIOR LAMP
(WITHOUT SUNROOF). ............... T- 52
INTERIOR LAMP (WITH SUNROOF) T- 53
INTERIOR AND SPOT LAMP
(WITHOUT SUNROOF). ............... T- 53
CARGO COMPARTMENT LAMP.. .. T- 54
TRUNK COMPARTMENT LAMP.. ... T- 54
COURTESY LAMP ....................... T- 54
CENTRAL PROCESSING UNIT (CPU) T- 55
SYSTEM DIAGRAM ...................... T- 55
CPU .......................................... T- 56
WARNING SYSTEM.. ...................... T- 58
WARNING BUZZER AND TIMER .... T- 58
WARNING AND INDICATOR LAMP T- 60
INSTRUMENT CLUSTER.. ............... T- 63
PREPARATION ............................ T- 63
STRUCTURAL VIEW ..................... T- 63
TROUBLESHOOTING ................... T- 64
INSTRUMENT CLUSTER
AND SPEEDOMETER CABLE.. .... T- 89
WATER THERMOSENSOR ............ T- 72
FUEL GAUGE SENDER UNIT.. ...... T- 73
REAR WINDOW DEFROSTER.. ........ T- 74
STRUCTURAL VIEW.. ................... T- 74
TROUBLESHOOTING ................... T- 75
FILAMENT .................................. T- 77
REAR WINDOW DEFROSTER
SWITCH .................................... T- 77
CRUISE CONTROL SYSTEM.. ......... T- 78
STRUCTURAL VIEW.. ................... T- 78
TROUBLESHOOTING GUIDE.. ....... T- 79
SELF-DIAGNOSTIC INSPECTION .... T- 80
TROUBLESHOOTING ................... T- 83
CRUISE CONTROL UNIT .............. T- 85
HORN ........................................... T- 88
HORN AND HORN RELAY.. .......... T- 88
AUDIO .......................................... T- 89
STRUCTURAL VIEW.. ................... T- 89
OUTLINE OF AUDIO.. .................. T- 90
SYSTEM ..................................... T- 91
TROUBLESHOOTING ................... T- 92
CAUSES OF NOISE ..................... T- 96
AUDIO COMPONENT.. ................. T- 98
DOOR SPEAKER .........................
REARSPEAKER .......................... ;-
- !3;
ANTENNA FEEDER ..................... T- 99
23UOTX-001

INDEX T
INSTRUMENT CLUSTER AND SWITCHES
23UOTX-00
1. Rear window defroster switch
7. Fuel gauge sender unit
Inspection
........................... page T-21 Removal / Installation ..................
page T-73
2. Remote control door mirror switch
Inspection ................................... page T-73
Inspection
........................... page T-20 8. Hazard warning switch
3. Ignition switch
Removal / installation .................. page T-20
Removal / Installation..
........ page T-20 Inspection ................................... page T-21
Inspection ........................... page
T-2 1 9. Cruise control main switch
4. Combination switch Inspection ...................................
page T-21
Removal / installation
.......... pages T-23, 25 10. Cruise control switch
Disassembly / Assembly ..... pages T-24, 26 Removal / Installation ..................
page T-20
Inspection
........................... pages T-27, 28 Inspection ................................... page T-21
5. Instrument cluster 11. Power window main switch
Troubleshooting..
................ page T-65 Inspection ................................... page T-22
Removal / Installation
.......... page T-69 12. Power window switch
Disassembly I Assembly ..... page T-70 Inspection ................................... page T-22
Inspection
........................... page T-71 13. Panel lamp control switch
6. Water thermosensor
Inspection ................................... page T-22
Removal / Installation..
........ page T-72
Inspection ........................... page T-72
T-3