wheel size MAZDA PROTEGE 1992 Workshop Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 1992, Model line: PROTEGE, Model: MAZDA PROTEGE 1992Pages: 1164, PDF Size: 81.9 MB
Page 702 of 1164

Q OUTLINE, TROUBLESHOOTING GUIDE
OUTLINE
SPECIFICATIONS
Wheels
Tires Standard Temporary spare __/
Size 13x5-J 14x5 l/2-JJ l4x4T
Offset mm (in)
45 (1.77)
Pitch circle diameter mm (in)
100 (3.94)
Material Steel or aluminum alloy Steel
Size P155/80R13’P175/70R131
PI 85/60Rl4 82H Tll5/70D14
79s 82s
Air pressure kPa (kgflcm’, psi)
216 (2.2, 32) 415 (4.2, 60)
23UOQX-001
TROUBLESHOOTING GUIDE _____ -_- ____ _ __.- -. -.-.--
Problem Possible Cause Remedy Page
Excessive or ir-
regular tire wear Refer to page Q-5 for details
Premature tire incorrect tire pressure Adjust Q-3
wear
Tire squeal Incorrect tire pressure Adjust Q-3
Tire deterioration Replace -
Road noise or Insufficient tire pressure Adjust Q-3
body vibration
Unbalanced wheel(s) Adjust Q-6
Deformed wheel(s) or tire(s) Repair or replace
Irregular tire wear Replace Q-5
“Shake” occurs Excessive tire and wheel runout
Replace
(Steering wheel Loose lug nuts
Tighten a-4
vibrates up/down) Unbalanced wheel(s)
Adjust Q-6
Cracked or worn engine mount rubber
Replace Sections Bl, B:
Cracked or worn transaxle mount rubber
Replace Sections Jl, J2
“Shimmy” occurs Excessive tire and wheel runout
Replace
(Steering wheel
Loose lug nuts Tighten a-4
vibrates left/right) Unbalanced wheel(s)
Adjust Q-6
irregular tire wear -
Q-5
insufficient tire pressure
Adjust Q-3
Damaged or worn front wheel bearing
Replace Section M
Malfunction of steering system -
Section N
Malfunction of suspension -
Section R
Steering wheel Incorrect tire pressure Adjust Q-3
pulls to one side Excessive or irregular tire wear -
Q-5
Malfunction of steering system -
Section N
Malfunction of braking system -
Section P
Malfunction of suspension -
Section R
General driving Unequal tire pressures Adjust Q-3
instability Deformed wheel(s) or tire(s) Repair or replace
Loose lug nuts Tighten Q-4
Malfunction of steering system -
Section N
Malfunction of suspension -
Section R
Uneven (one-sided) Unequal tire pressures
Adjust Q-3
braking Malfunction of braking system -
Section P
Heavy handling Insufficient tire pressures Adjust Q-3
Malfunction of steering system -
Section N
Malfunction of suspension -
Section R
Steering wheel Insufficient tire pressures Adjust Q-3
does’t return Malfunction of steering system -
Section N
properly Malfunction of suspension -
Section R
731100x-or . _. -,
Q-2
Page 703 of 1164

WHEELS AND TIRES
WHEELS AND TIRES
SPECIAL NOTES ABOUT WHEELS AND TIRES
1. Do not use wheels or tires other than the specified types.
2. Aluminum wheels are easily scratched. When washing them, use a soft cloth, never a wire brush. If the
vehicle is steam cleaned, do not allow boiling water to contact the wheels.
3. If alkaline compounds (such as saltwater or road salts) get on aluminum wheels, wash them as soon as
possible to prevent damage. Use only a neutral detergent.
9MUOQX-004
NOTES REGARDING TIRE REPLACEMENT
Note the following points when tires are to be removed from or mounted onto the wheels.
1. Be careful not to damage the tire bead, the rim bead, or the edge of the rim.
2. Use a wire brush, sandpaper, or cloth to clean and remove all rust and dirt from the rim edge and the
rim bead.
3. When cleaning aluminum wheels, use a soft cloth, never a wire brush or sandpaper.
4. Remove any pebbles, glass, nails, and other foreign items embedded in the tire tread.
5. Be sure the air valve is installed correctly.
6. Apply a soapy solution to the tire bead and the edge of the rim.
7. After mounting a tire onto a wheel, inflate the tire to 250-300 kPa (2.55-3.06 kg/cm2, 35.55-42.66
psi). Check to be sure that the bead is seated correctly onto the rim and that there are no air leaks. Then
reduce the pressure to the specified level.
8. If a tire iron is used to change a tire on an aluminum wheel, be sure to use a piece of rubber between
the iron lever and the wheel to avoid damage to the wheel. Work should be done on a rubber mat, not
on a hard or rough surface.
03UOQX-004
23UOOX-003
TIRE
I
AIR VALVE
INSPECTION / ADJUSTMENT
Air Pressure
Air pressure
Check the air pressure of all tires, including the spare tire, with
an air pressure gauge. If necessary, adjust the air pressure.
Tire Size Air Pressure kPa (kgf/cm2, psi)
Front Tires Rear Tires
P155180R13 79s
PI 75/70R13 82s 216 (2.2, 32) 216 (2.2, 32)
P185/60R14 82H
1115/70D14 415 (4.2, 60)
Air Leakage
Verify that there is no air leakage from the air valve.
I I 13UOOX-008
Q-3
Page 1033 of 1164

TECHNICAL DATA
Q. WHEELS AND TIRES
Item Specifications
Wheel
Size
Off set Standard: 13x5-J, 14x5 l/2-JJ
Temporary
mm (in) 1 _ spare: 14x4-T
45 (1.77)
I Diameter of oitch circle
mm (in) I 100 (3.94)
r I Pl
-
Inflation pressure kPa (kg/cm*, psi) Front 1 8
I 9
Runout limit
Unbalance limit mm (in) ;lii.raltLa’
a (02) ’
13 inch wheel: 11 (0.
R. SUSPENSION Item Specifications
Suspension type Strut
)e Double-acting, oil-filled
I Shock absorber tyf
Coil spring
Type
Dimension
Type Front Taper wound
Rear Straight wound
See next page
Torsion bar
I
I C.rrn,
19.1 (0.75)
20.0 (0.79)
22.0 (0.87)
21 .O f0.83)
Wheel alignment
(“‘Unladened) BP SOHC ;;a;
Diameter
mm (in) BP DOHC - ;la;t
Front -
B6 SOHC
Rear 20.0 (0.79)
Maximum Inner 4o” f 2O
steering angle Outer
Total mm (in) 2 f 3 (0.08 j
Front toe-in
dearee
.-.._
Rear
.--. I --- ~~
Camber angle
Caster angle
Kingpin angle
I Total
I mm OnI I I toe-in
1 dearee I , --U’-- 1
Camber angle
I 33O * 2O
: 0.12)
0.2O f 0.3O
-0OO5’ * 45’
1055’ * 55’
12O25’
2 f 3 (0.08 f 0.12)
0.2O f 0.3O
-0°20’ f 45’
l ’ Fuel tank full; radiator coolant and engine ail at specified level; and spare tire, jack, and tools in designated posmons.
TD-19