change wheel MERCEDES-BENZ CLA 2014 Owners Manual

Have aftermarketaccessories installed at
a qualified specialist workshop.
You could jeopardize the operating safety of
your vehicle if you use parts, tires and wheels
as well as accessories relevant to safety
which have not beenapproved by Mercedes.
This could lead to malfunctions in safety-
relevant systems, e.g. the brake system.Use
only genuine Mercedes-Benz parts or parts of
equal quality. Only use tires, wheels and
accessories that have been specifically
approved for your vehicle.
Genuine Mercedes-Benz parts are subject to
strict quality control. Every part has been
specifically developed, manufactured or
selected for and adapted to Mercedes-Benz
vehicles. Only genuine Mercedes-Benz parts
should therefore be used.
More than 300,000 different genuine
Mercedes-Benz parts are available for
Mercedes-Benz models.
All authorized Mercedes-Benz Centers
maintain a supply of genuine Mercedes-Benz
parts for necessary service and repair work.
In addition, strategically located parts
delivery centers provide quick and reliable
parts service.
Always specify the vehicle identification
number (VIN) (Ypage 344) and the engine
number (Ypage 345) when ordering genuine
Mercedes-Benz parts.
Operator's Manual
General notes
Before you first drive off, read this Operator's
Manual carefully and familiarize yourselfwith
your vehicle.
For your own safety and a longer vehicle life,
follow the instructions and warning notices in
this manual. Disregarding themmay lead to
damage to the vehicle or personal injury.
Vehicle damage resulting from the disregard
of the instructions is not covered by the
Mercedes-BenzLimited Warranty.
Vehicle equipment
This Operator's Manual describes all models
and all standard and optional equipmentof
your vehicle available at thetime of going to
print. Country-specific differences are
possible.Bear in mind that your vehicle may
not feature all functions described here. This
also applies to safety-relevant systems and
functions. The equipment in your vehicle may
therefore differ from that shown in the
descriptions and illustrations.
The original purchase agreement lists all
systems installed in your vehicle.
Should you have any questions concerning
equipment and operation, please consult an
authorized Mercedes-BenzCenter.
The Operator's Manual and Maintenance
Booklet are important documents and should
be kept in the vehicle.
Service and vehicle operation
Service and literature
Your vehicle is covered under the terms of the
warranties printed in the Service and
Warranty Information booklet. Your
authorized Mercedes-BenzCenter will
exchange or repair any defective parts
originally installed in the vehicle in
accordance with the termsofthe following
warranties:
RNew Vehicle Limited Warranty
REmission Systems Warranty
REmission Performance Warranty
RCalifornia, Connecticut, Maine,
Massachusetts, New York, Pennsylvania,
Rhode Island and Vermont Emission
Control Systems Warranty
RState warranty enforcement laws (lemon
laws)
22Introduction

Operating safety
Important safety notes
GWARNING
If you do not have the prescribed service/
maintenance work or any required repairs
carried out, this can result in malfunctions or
system failures. There is a risk of an accident.
Always have the prescribed service/
maintenance work as well as any required
repairs carried out at a qualified specialist
workshop.
GWARNING
If you switch off the ignition while driving,
safety-relevant functionsare only available
with limitations, or not at all.This could affect,
for example, the power steering and the brake
boosting effect.You will require considerably
more effort to steer and brake. There is a risk
of an accident.
Do not switch off the ignition while driving.
GWARNING
Modifications to electronic components, their
software as well as wiring can impair their
function and/or the function of other
networked components. In particular,
systems relevant to safety could also be
affected. As a result, these may no longer
function as intended and/or jeopardize the
operating safety of the vehicle. There is an
increased risk of an accident and injury.
Never tamper with the wiring as well as
electronic components or their software. You
should have all work to electrical and
electronic equipment carried out at a qualified
specialist workshop.
!There is a risk of damage to the vehicle if:
Rthe vehicle becomes stuck,e.g. on a high
curb or an unpaved road
Ryou drive too fastover an obstacle, e.g.
a curb or a hole in the road
Ra heavy object strikes the undercarriage
or parts of the chassis.
In situations like this, the body, the
undercarriage, chassis parts, wheels or
tires could be damaged without the
damage being visible.Components
damaged in this way can unexpectedly fail
or, in the case of an accident, no longer
withstand the strain they are designed to.
If the underbody paneling is damaged,
combustible materials such as leaves,
grass or twigs can gather between the
underbody and the underbody paneling. If
these materials come in contact with hot
parts of the exhaust system for an
extended period, they can catch fire.
Have the vehicle checked and repaired
immediately at a qualified specialist
workshop. If on continuing your journey
you notice that driving safety is impaired,
pull over and stop the vehicle immediately,
paying attention to road and traffic
conditions. In such cases, visit a qualified
specialist workshop.
Declarations of conformity
Vehicle components which receive
and/or transmit radio waves
USA:"The wireless devices of this vehicle
comply with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: 1) These devices may not cause
harmful interference, and 2) These devices
must accept any interference received,
including interference that may cause
undesired operation. Changes or
modifications not expressly approved by the
party responsible for compliance could void
the user’s authority to operate the
equipment."
Canada:"The wireless devices of this vehicle
comply with Industry Canada license-exempt
RSS standard(s). Operation is subject to the
following two conditions: (1) These devices
may not cause interference, and (2) These
devices must accept any interference,
24Introduction

decisive role in the deployment of an air bag,
nor do they provide an indication of air bag
deployment.
The vehicle may be deformed significantly,
e.g. the hood or the fender, without an air bag
being deployed. This is the case if only parts
which are relatively easily deformed are
affected and the rate of deceleration is not
high. Conversely, air bags may be deployed
even though the vehicle suffers only minor
deformation. This is the case if, for example,
very rigid vehicle parts such as longitudinal
body members are hit, and sufficient
deceleration occurs as a result.
iThe front Emergency Tensioning Devices
can only be triggered if the seat belt
tongues on the front seats are correctly
engaged in the seat belt buckles.
iNot all air bags are deployed in an
accident. The differentair bag systems
work independently of each other.
How the air bag system works is
determined by predicting the severity of
the accident, especially vehicle
deceleration or acceleration, and the type
of accident:
Rhead-on collision
Rside impact
Rrollover
Safety guidelines for seat belts,
Emergency Tensioning Devices (ETDs)
and air bags
GWARNING
RDamaged seat belts or seat belts that have
been subjected to stress in an accident
must be replaced. Their anchoring points
must also be checked. Only use seat belts
installed or supplied by an authorized
Mercedes-Benz Center.
RAir bags and pyrotechnic Emergency
Tensioning Devices (ETDs) contain
perchlorate material, which may require
special handling and regard for the
environment. Check your national disposal
guidelines. In California, see
www.dtsc.ca.gov/HazardousWaste/
Perchlorate/index.cfm.
RAir bags and ETDs are designed to function
on a one-time-only basis. An air bag or ETD
that has deployed must be replaced.
RDo not pass seat belts over sharp edges.
They could tear.
RDo not make any modification that could
change the effectiveness of the seat belts.
RDo not bleach or dye seat belts, as this may
severely weaken them. In a crash, they may
not be able to provide adequate protection.
RDo not make any modifications to the SRS
wiring or components.
RDo not modify or remove any components
or parts of the SRS.
RDo not install additional trim material, seat
covers, badges, etc.to the:
-padded steering wheel boss
-knee bag covers
-front-passenger air bag cover
-outer side of front seat bolsters
-outer seat bolsters of the rear bench seat
backrest
-roof frame trim
RDo not install additional electrical/
electronic equipment on or near SRS
components and wiring.
RKeep the area between the air bags and
occupants free of objects(e.g. packages,
handbags, umbrellas etc.).
RDo not hang any objects such as coat
hangers on the coat hooks or the grab
handle above the door. These items may be
thrown around in the vehicle and cause
head and other injuries when the window
curtain air bag is deployed.
RAir bag system components will be hot after
an air bag has inflated. Do not touch them.
RNever rest your feet on the dashboard or
the seat. Always keep both feet on the floor
in front of the seat.
40Occupant safety
Safety

Adjusting the steering wheel
GWARNING
If the steering wheel is unlocked while the
vehicle is in motion, it could change position
unexpectedly. This could causeyou to lose
control of the vehicle. There is a risk of an
accident.
Before starting off, make sure the steering
wheel is locked. Never unlock the steering
wheel while the vehicle is in motion.
Release lever
To adjust the steering wheel height
"To adjust the steering wheel position
(fore-and-aft adjustment)
XPush release leverdown completely.
The steering column is unlocked.
XAdjust the steering wheel to the desired
position.
XPush release leverup completely.
The steering column is locked.
XCheck if the steering column is locked.
When doing so, try to push the steering
wheel up or down or try to move it in the
fore-and-aft direction.
Mirrors
Rear-view mirror
XAnti-glare mode:flick anti-glare lever
forwards or back.
Exterior mirrors
Adjusting the exterior mirrors
GWARNING
The exterior mirror on the front-passenger
side reduces the size of the image. Visible
objects are actually closer than they appear.
This means that you could misjudge the
distance from road users traveling behind,
e.g. when changing lane. There is a risk of an
accident.
For this reason, always make sure of the
actual distance from the road users traveling
behind by glancing over your shoulder.
Mirrors97
Seats, steering wheel and mirrors
Z

Active:
Rif you are driving at speeds below 25 mph
(40 km/h) and switch on the turnsignal or
turnthe steering wheel.
Rif you are driving at speeds between
25 mph(40 km/h) and 45 mph(70 km/h)
and turn the steering wheel.
Not active:if you are driving at speeds above
25 mph (40 km/h) or switch off the turn
signal or turn the steering wheel to the
straight-ahead position.
The cornering lamp may remain lit for a short
time, but is automatically switched off after
no more than three minutes.
Extended range fog lamps
The extended range fog lamps reduce the
glare experienced by the driverand improve
the illuminationofthe edge of the road.
Active:if you are driving at speeds below
40 mph (70 km/h) and you switch on the rear
fog lamp.
Not active:if, following activation, you are
driving at speeds above 60 mph (100 km/h)
or if you switch off the rear fog lamp.
Adaptive Highbeam Assist
Important safety notes
GWARNING
Adaptive Highbeam Assist does not recognize
road users:
Rwho have no lights, e.g. pedestrians
Rwho have poor lighting, e.g. cyclists
Rwhose lighting is blocked, e.g. by a barrier
In very rare cases, Adaptive Highbeam Assist
may fail to recognize other road users that
have lights, or may recognize them too late.
In this or similar situations, the automatic
high-beam headlamps will not be deactivated
or activated regardless. There is a risk of an
accident.
Always carefully observe the traffic conditions
and switch off the high-beam headlamps in
good time.
Adaptive Highbeam Assist cannot take into
account road, weather or traffic conditions.
Adaptive Highbeam Assist is only an aid. You
are responsible for adjusting the vehicle's
lighting to the prevailing light, visibility and
traffic conditions.
In particular, the detection of obstacles can
be restricted if there is:
Rpoor visibility, e.g. due to fog, heavy rain or
snow
Rdirt on the sensors or the sensors are
obscured
General notes
You can use this function to set the
headlamps to change between low beam and
high beam automatically.The system
recognizes vehicles with their lights on, either
approaching from the opposite direction or
traveling in front of your vehicle, and
consequently switches the headlamps from
high beam to low beam.
The system automatically adapts the low-
beam headlamp range depending on the
distance to the other vehicle. Once the
108Exterior lighting
Lights and windshield wipers

Halogen headlamps
Turnsignal lamp: PY 21 W
Low-beam headlamp/daytime running
lamp/parking lamp/standing lamp:
H15 55 W/15 W
"Low-beam headlamp: H7 55 W
Vehicles with IntelligentLight System
Cornering lamp: H7 55 W
Tail lamp (halogen headlamps)
Rear fog lamp: P 21 W
Brake lamp: W 16 W
"Brake lamp: W 16 W
!Turn signal lamp: PY 21 W
Backup lamp: W 16 W
Changing the front bulbs
Removing and installing thecover in the
front wheel housing
You must remove the cover from the front
wheel housing before you can change the
frontbulbs.
XTo remove:switch off the lights.
XTurn the frontwheels inwards.
XTurn rotary knobthrough 90°.
Coveris released.
XPush coverdown.
XTo install:push coverup.
XTurn rotary knobthrough 90°.
Coveris locked.
Low-beam headlamps (halogen
headlamps)
112Replacing bulbs
Lights and windshield wipers

Engaging park position P
XWhen the vehicle is stationary, pressP
button.
Transmission positions
Parkposition
Do not shift the transmission into
positionPunless the vehicle is
stationary (Ypage 153). The
parking lock should not be used as
a brake when parking.Always
apply the electronic parking brake
in additionto the parking lock in
order to secure the vehicle.
If the vehicle electronics are
malfunctioning, the transmission
may be locked in positionP.
Have the vehicle electronics
checked immediately at a qualified
specialist workshop.
Reverse gear
Only shift the transmission toR
when the vehicle is stationary.

Neutral
No power is transmitted from the
engine to the drive wheels.
Releasing the brakes will allow you
to move the vehicle freely, e.g. to
push it or tow it.
If ESP®is deactivated or faulty:
only shift the transmission to
positionNif the vehicle is in danger
of skidding, e.g. on icy roads.
When you switch off the engine, the
automatic transmission
automatically shifts into neutralN.
Drive
The automatic transmission
changes gear automatically. All
forward gears are available.
Changing gear
The automatic transmission shifts to the
individual gears automatically when it is in
transmission positionD.This automatic
gearshifting behavior is determined by:
Rthe selected drive program (Ypage 146)
Rthe position of the accelerator pedal
Rthe road speed
Driving tips
Holding the vehicle stationary on uphill
gradients
GWARNING
If the clutch overheats, the electronic
management system is automatically
deactivated. This interrupts the power
transmission. The vehicle may, for example,
roll backwards on gradients. There is a risk of
an accident.
Never hold the vehicle stationary on uphill
gradients by depressing the accelerator.
Automatic transmission145
Driving and parking
Z

AMG vehicles
CControlled
Efficiency
Comfortable, economical
driving
SSportSporty driving style
MManualManual gear shifting
Only change from automatic drive program
CorSto manual drive programMwhen the
vehicle is stationary.
XPress program selector button
repeatedly until the letterfor the desired
gearshift program appears in the
multifunction display.
iThe automatic transmission shifts to
automatic drive programCeach time the
engine is started.
iFor further information on the automatic
drive program, see (Ypage 147).
Steering wheel paddle shifters
Left steering wheel paddle shifter (shifts
down)
Right steering wheel paddle shifter (shifts
up)
In drive programM, you can change gear
yourself using the steering wheel paddle
shifters.
If you pull the left or right steering wheel
paddle shifter when in automatic drive
programE(drive programCon AMG vehicles)
orS, the automatic transmission shifts into
drive programMfor a limited time.
Depending on which paddle shifter is pulled,
the automatic transmission immediately
shifts into the next gear down or up.
AMG vehicles:you can activate drive
programMRACE START (Ypage 173) using
the steering wheel paddle shifters.
iYou can only change gear with the
steering wheel paddle shifters when the
transmission is in positionD.
iFor further information on the manual
drive program, see (Ypage 148).
Automatic drive program
Drive programE(drive programCon MAG
vehicles) is characterized by the following:
Rcomfort-oriented engine settings
Roptimal fuel consumption resulting from
the automatic transmission shifting up
sooner
Automatic transmission147
Driving and parking
Z

Rthe vehicle pulling away moregently in
forward and reverse gears, unless the
accelerator pedal is depressed fully
Rincreased sensitivity. This improves driving
stability on slippery road surfaces, for
example
Rthe automatic transmission shifting up
sooner.This results in the vehicle being
driven at lower engine speeds and the
wheels being less likely to spin
Drive programSis characterized by the
following:
Rsporty engine settings
Rthe automatic transmission shifting up
later
Rthe fuel consumption possibly being higher
as a result of the later automatic
transmission shift points
Manual drive program
Introduction
In manual drive programM, you can change
gear yourself by using the steering wheel
paddle shifters. For this, the transmission
must be in positionD. The gear currently
selected and engaged is shown in the
multifunction display.
Manual drive programMdiffers from drive
programsE(drive programCon AMG
vehicles) andSwith regard to spontaneity,
responsiveness and smoothness of gear
changes.
GearDriving situations
You can use the engine's braking
effect
\nYou can use the braking effect of
the engine on downhill gradients
and for driving:
Ron steep mountain roads
Rin mountainous terrain
Rin arduous conditions
To use the braking effect of the
engine on extremely steep downhill
gradients and on long downhill
stretches
Switching on the manual drive program
Activating permanently
XPress the program selector button
(Ypage 146) repeatedly untilMappears in
the multifunction display.
Manual drive programMremains active
until drive programE(drive programCon
AMG vehicles) orSis selected.
Activating temporarily
XPull the right or left steering wheel paddle
shifter (Ypage 147).
Mis shown in the multifunction display.
Manual drive programMis temporarily
active. Depending on which paddle shifter
is pulled, the automatic transmission
immediately shifts into the next gear down
or up.
iWhen manual drive programMis
activated via the steering wheel paddle
shifters, the temporarily active manual
drive programMwill be deactivated
automatically after a limited time, if the
driving situation permits. The automatic
transmission switches to the previously
activated drive programE(drive program
Con AMG vehicles) orS.When driving on
downhill gradients, the temporarily active
manual drive programMwill only be
deactivated if the accelerator pedal is
depressed while the vehicle is rolling
downhill.
148Automatic transmission
Driving and parking

Upshifting
XPull the right-hand steering wheel paddle
shifter (Ypage 147).
The automatic transmission shifts up to the
next gear.
iAll vehicles (except AMG vehicles):in
order to preventengine damage the
automatic transmission automatically
shifts up:
Rif the maximumengine speed on the
currently engaged gear is reached and
Ryou continue to accelerate.
AMGvehicles:
!In manual drive programM, the automatic
transmission does not shiftup
automatically evenwhen the engine
limiting speed for the current gear is
reached. When the engine limiting speed is
reached, the fuel supply is cut to prevent
the engine from overrevving. Always make
sure that the engine speed does not reach
the red area of the tachometer. There is
otherwise a risk of engine damage.
AMG vehicles
!In manual drive programM, the automatic
transmission does not shift up
automatically even when the engine
limiting speed for the current gear is
reached. When the engine limiting speed is
reached, the fuel supply is cut to prevent
the engine from overrevving. Always make
sure that the engine speed does not reach
the red area of the tachometer. There is
otherwise a risk of engine damage.
Gear indicator
Upshift indicator
Before the engine speed reaches the red area,
an upshift indicator will be shown in the
multifunction display.
XIf the color in the speedometer
multifunction display changes to red and
theUPdisplay message is shown, shift up
a gear.
Downshifting
XPull the left-hand steering wheel paddle
shifter (Ypage 147).
The automatic transmission shifts down to
the next gear.
iIf you slow down or stop without shifting
down, the automatic transmission
automatically shifts down.
iFor maximum acceleration, pull the left-
hand steering wheel paddle shifter until the
transmission selects the optimum gear for
the current speed.
iIf the engine exceeds the maximum
engine speed when shifting down, the
automatic transmission protects against
engine damage by not shifting down.
Kickdown
AMG vehicles:kickdown is only possible in
temporary manual drive programM.
You can also use kickdown for maximum
acceleration in manual drive programM.
XDepress the accelerator pedal beyond the
pressure point.
The automatic transmission shifts to a
lower gear depending on the engine speed.
XShift back up once the desired speed is
reached.
iDuring kickdown, you cannot change gear
using the steering wheel paddle shifters.
iIf you apply full throttle, the automatic
transmission shifts up to the next gear
when the maximum engine speed is
Automatic transmission149
Driving and parking
Z