page 31 MERCEDES-BENZ GLC 2017 Repair Manual

X
Adjust the seat accordingly ( Y
page 100).X
On the driver's side, adjust the steering wheel
( Y
page 105) and the exterior mirrors
( Y
page 107).X
Press memory button M and then press one of
the memory position buttons 1 , 2 or 3 within
three seconds.
The settings are stored in the selected preset
position. A tone sounds when the settings
have been completed.
Calling up a stored setting X
Press and hold the relevant memory position
button 1 , 2 or 3 until the following compo-
nents are in the saved position: R
Seat R
Steering wheel R
Exterior mirrors R
Head-up display
i If you release the memory position switch,
the seat, steering wheel and mirror setting
functions stop immediately. The head-up dis-
play continues to be adjusted.110
Memory function
Seats, steering wheel an d mirrors

Exterior lighting
General notes USA only: if you wish to drive during the daytime
without lights, switch off the Daytime Run‐
ning Lights function via the on-board com-
puter ( Y
page 223).
Setting the exterior lighting
Setting options Exterior lighting can be set using the: R
light switch ( Y
page 111)R
combination switch ( Y
page 112)R
on-board computer ( Y
page 223)
Light switch Operation
G c
Left-hand standing lampsH d
Right-hand standing lampsI `
Parking lamps, license plate and
instrument cluster lightingJ X
Automatic headlamp mode, controlled
by the light sensor
K X
Low-beam/high-beam headlamps

The system automatically adapts the low-beam
headlamp range depending on the distance to
the other vehicle. Once the system no longer
detects any other vehicles, it reactivates the
high-beam headlamps.
The system's optical sensor is located behind
the windshield near the overhead control panel.
Important safety notes
G WARNING
Adaptive Highbeam Assist does not recognize
road users: R
who have no lights, e.g. pedestrians R
who have poor lighting, e.g. cyclists R
whose lighting is blocked, e.g. by a barrier
On very rare occasions, Adaptive Highbeam
Assist may fail to recognize other road users
that have lights, or may recognize them too
late. In this, or in similar situations, the auto-
matic high-beam headlamps will not be deac-
tivated or will be activated regardless. There is
a risk of an accident.
Always carefully observe the traffic conditions
and switch off the high-beam headlamps in
good time.
Adaptive Highbeam Assist cannot take into
account road, weather or traffic conditions.
Adaptive Highbeam Assist is only an aid. You are
responsible for adjusting the vehicle's lighting
to the prevailing light, visibility and traffic con-
ditions.
In particular, the detection of obstacles can be
impaired if: R
there is poor visibility, e.g. due to fog, heavy
rain or snow R
there is dirt on the sensors or anything else
covering the sensors
Switching Adaptive Highbeam Assist
on/off X
To switch on: turn the light switch to the
X position.X
Press the combination switch forwards
beyond the pressure point ( Y
page 112).
The

Protect bulbs from moisture during operation.
Do not allow bulbs to come into contact with
liquids.
Replace only the bulbs listed ( Y
page 116).
Have the bulbs that you cannot change yourself
replaced at a qualified specialist workshop.
If you require assistance replacing bulbs, con-
sult a qualified specialist workshop.
If the new bulb still does not light up, consult a
qualified specialist workshop.
Headlamps and lights are an important aspect of
vehicle safety. You must therefore make sure
that these function correctly at all times. Have
the headlamp setting checked regularly.
Vehicles with LED headlamps: the front and
rear light clusters of your vehicle are equipped
with LED bulbs. Do not replace the bulbs your-
self. Contact a qualified specialist workshop
which has the necessary specialist knowledge
and tools to carry out the work required.
Overview of bulb types You can replace the following bulbs. The bulb
type can be found in the legend.
Halogen headlampsC
Low-beam headlamp: H7 55 W
D
High-beam headlamp: H7 55 W

High-beam headlamps X
Switch off the lights. X
Open the hood. X
Turn housing cover C counter-clockwise and
remove it. X
Push bulb holder D upwards and pull out.X
Pull defective bulb out of bulb holder D .X
Insert new bulb into bulb holder D .X
Insert bulb holder D into groove with lug at
top. X
Push bulb holder D down until it engages
audibly. X
Press on housing cover C and turn it clock-
wise.
Turn signals
X
Remove the cover in the front wheel housing
( Y
page 117). X
Turn bulb holder C counter-clockwise using
the grip under the headlamp casing and
remove it downwards with bulb. X
Turn defective bulb counter-clockwise and
remove it from bulb holder C .X
Insert new bulb into bulb holder C . X
Insert bulb holder C , turn it clockwise and
lock. X
Replace the cover in the front wheel housing
( Y
page 117).
Removing and installing the cover in the
front wheel housing You must remove the cover of the front wheel
housing before you can change the front turn
signal lamp.
X
To remove: switch off the lights. X
Turn the front wheels inwards. X
Turn rotary knob C 180° outwards until it
stops using a suitable object.
Cover D is released. X
Fold cover D up. X
To install: insert cover D into the left, right
and two lower catches. X
Turn rotary knob C 180° inwards until it
stops using a suitable object.
Cover D is locked.Replacing bulbs 117
Lights and windshield wipers Z

Overview of climate control systems
General notes Observe the settings recommended on the fol-
lowing pages. The windows could otherwise fog
up.
To prevent the windows from fogging up: R
switch off climate control only briefly R
switch on air-recirculation mode only briefly R
switch on the cooling with air dehumidifica-
tion function R
activate the "Windshield defrosting" function
briefly, if required
Climate control regulates the temperature and
air humidity in the vehicle interior. The interior
filter cleans the air, thus improving the interior
climate.
The "Cooling with air dehumidification" function
is only available when the engine is running.
Optimum climate control is only achieved with
the side windows and roof closed.
If you start the engine using your smartphone,
the last selected climate control setting is reac-
tivated ( Y
page 134). The integrated filter filters out most particles of
dust and soot and completely filters out pollen.
It also reduces gaseous pollutants and odors. A
clogged filter reduces the amount of air supplied
to the vehicle interior. For this reason, you
should always observe the interval for replacing
the filter, which is specified in the Maintenance
Booklet. As it depends on environmental condi-
tions, e.g. heavy air pollution, the interval may
be shorter than stated in the Maintenance Book-
let.
i Ventilate the vehicle for a brief period during
warm weather, e.g. using the convenience
opening feature ( Y
page 91). This will speed
up the cooling process and the desired inte-
rior temperature will be reached more
quickly.
i It is possible that the blower may be activa-
ted automatically 60 minutes after the Smart-
Key has been removed depending on various
factors, e.g. the outside temperature. The
vehicle is then ventilated for 30 minutes to dry
the automatic climate control.
Control panel for dual-zone automatic climate control
Example: control panel for dual-zone automatic climate control
C
Sets the temperature, left ( Y
page 126)
D
Sets the air distribution ( Y
page 126)

Switching cooling with air dehumidification on/off
General notes If you deactivate the "Cooling with air-dehumidification" function, the air inside the vehicle will not
be cooled. The air inside the vehicle will also not be dehumidified. The windows can fog up more
quickly. Therefore, only deactivate the "Cooling with air-dehumidification" function briefly.
The "Cooling with air dehumidification" function is only available when the engine is running. The air
inside the vehicle is cooled and dehumidified according to the temperature selected.
Condensation may drip from the underside of the vehicle when it is in cooling mode. This is normal
and not a sign that there is a malfunction.
Activating/deactivating X
Press the Z rocker switch up or down.
The indicator lamp above the rocker switch lights up or goes out.
Problems with the "Cooling with air dehumidification" function Problem
Possible causes/consequences and P Solutions
The indicator lamp above
the Z rocker switch
remains off. The cooling
with air dehumidification
function cannot be acti-
vated via the multimedia
system any longer
( Y
page 273). Cooling with air dehumidification has been deactivated due to a mal-
function. X
Visit a qualified specialist workshop.
Setting climate control to automatic
General notes In automatic mode, the set temperature is main-
tained automatically at a constant level. The
system automatically regulates the temperature
of the dispensed air, the airflow and the air dis-
tribution.
During automatic controlling, the "Cooling with
air dehumidification" function is activated.
Automatic control X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 132).X
To activate: press the X rocker switch up
or down.
The indicator lamp above the X rocker
switch lights up. X
Set the desired temperature using the

Adjusting the climate mod e settingsIn automatic mod e you can select th e followin g
airflow setting s for th e driver's and front-
passenger areas :
FOCUS high airflow, slightly cooler setting
MEDIUM medium airflow, standard setting
DIFFUS El ow airflow, slightly warmer and draft-
free settingX
To set: set the climate mode using the mul-
timedia system ( Y
page 272).
Setting the temperature Dual-zone automatic climate control: different
temperatures can be set for the driver's and
front-passenger sides. X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 132).X
To increase or reduce: press rocker switch

The climate control system switches to the
following functions: R
high airflow R
high temperature R
air distribution to the windshield and front
side windows R
air-recirculation mode off
i If necessary, the "Cooling with air dehumid-
ification" function is activated. In this case,
the indicator lamp above the Z rocker
switch remains switched off. X
To switch off: press rocker switch d up or
down.
The indicator lamp above the d rocker
switch goes out. The previously selected set-
tings are restored. Air-recirculation mode
remains deactivated.
Defrosting the windows
Windows fogged up on the inside X
Activate the "Cooling with air dehumidifica-
tion" function with the Z rocker switch.X
Switch on automatic mode using the X
rocker switch. X
If the windows continue to fog up, activate the
"Windshield defrosting" function using the
d rocker switch. i You should only select this setting until the
windshield is clear again.
Windows fogged up on the outside X
Activate the windshield wipers. X
Switch on automatic mode using the X
rocker switch.
i If you clean the windows regularly, they do
not fog up so quickly.
Rear window defroster
General notes The rear window defroster has a high current
draw. You should therefore switch it off as soon
as the rear window is clear. Otherwise, the rear
window defroster switches off automatically
after several minutes.
If the battery voltage is too low, the rear window
defroster may switch off.
Activating/deactivating X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 132). X
Press rocker switch l up or down.
The indicator lamp above rocker switch l
lights up or goes out.
Problems with the rear window defroster Problem
Possible causes/consequences and P Solutions
The rear window
defroster has deactiva-
ted prematurely or can-
not be activated. The battery has not been sufficiently charged. X
Switch off any consumers that are not required, e.g. reading lamps,
interior lighting or the seat heating.
When the battery is sufficiently charged, the rear window defroster
can be activated again.
Switching air-recirculation mode
on/off
General notes
You can also temporarily deactivate the flow of
fresh air manually if unpleasant odors are enter-
ing the vehicle from outside. The air already
inside the vehicle will then be recirculated. If you switch on air-recirculation mode, the win-
dows can fog up more quickly, in particular at
low temperatures. Only use air-recirculation
mode briefly to prevent the windows from fog-
ging up.Operating the climate control systems 127
Climate control

Activating/deactivating X
Turn th e SmartKey to position H in th e igni-
tion loc k ( Y
page 132).X
To activate: press rocke r switch r up or
down .
The indicator lamp abov e rocke r switch r
lights up.
Air-recirculation mod e switches on automati-
cally: R
at high outside temperatures R
in a tunne l (vehicles wit h a navigation system
only)
The indicator lamp abov e th e r rocke r
switch is no t lit when automatic air-recirculation
mod e is activated. Outside air is added after
about 30 minutes. X
To deactivate: press th e r rocke r switch
up or down .
The indicator lamp abov e th e r rocke r
switch goe s out .
Air-recirculation mod e deactivates automati-
cally: R
after approximately fiv e minute s at outside
temperatures belo w approximately 41 ‡
(5 †) R
after approximately fiv e minute s if coolin g
wit h air dehumidification is deactivatedR
after approximately 30 minute s at outside
temperatures abov e approximately 41 ‡
(5 †) if th e "Cooling wit h dehumidification "
function is activated
Perfu me atomizer
Operating the perfu me at omi zer
G WARNIN G
If children open th e vial, they could drink th e
perfum e or it could come int o contact wit h
their eyes. There is a ris k of injury. Therefore ,
do no t leav e children unsupervised in th e vehi-
cle .
If th e perfum e liquid has been drunk, consult
a doctor. If perfum e comes int o contact wit h
your eyes or skin, rinse th e eyes wit h clean
water. If you continu e to experience difficul-
ties, consult a doctor. H Environmenta l not e
Full vials mus t no t be dis-
posed of wit h household
waste. The y mus t be collec -
te d separately and recycle d
to protect th e environment.
Dispose of full vials in an
environmentally responsibl e
manne r and tak e them to a
harmful substance collec -
tion point.
C
Vial lid D
Vial
The perfum e atomizer help s to improve drivin g
comfort .
Via th e multimedia system you can :R
switch th e perfum e atomizer on/off
( Y
page 272) R
regulat e th e perfum e intensit y ( Y
page 272)
The followin g condition s can affec t your percep-
tion of th e perfum e intensity:R
operating mod e of th e climat e control systemR
interior temperature R
time of year or day R
air humidit y R
physiological condition of occupants, e.g. fati-
gue or hunger
The perfum e atomizer is active only when th e
glov e box is closed.
The perfum e atomizer is provided wit h a pre-fil-
led vial. You can also choos e from a variet y of
filled perfum e vials and an empty vial whic h you
can fill yourself .
If you refill an empty perfum e vial, observ e th e
separat e information sheet attached to th e vial.128
Operating the climate control systems
Climate control