Mercury Mountaineer 1998 Owner's Manuals

Cleaning and maintaining the
safety belts
Clean the safety belts with a mild
soap solution recommended for
cleaning upholstery or carpets. Do
not bleach or dye the belts,
because these actions may weaken
the belt webbing.
Check the safety belt system
periodically to make sure there are
no nicks, wear or cuts. If your
vehicle has been involved in an
accident, refer to theSafety belt
maintenancesection in the
Seating and safety restraints
chapter.
Cleaning the built-in child seat
(if equipped)
Clean with mild soap and water.
Do not use household cleaning
products because they may
weaken the safety belt webbing or
damage the vinyl parts of the seat.
The child seat liner is removable
and may be machine-washed and
air dried.
Underbody
Flush the complete underside of
vehicle frequently. Keep body
drain holes unplugged. Inspect for
road damage.
Cleaning leather seats
(if equipped)
For routine cleaning, wipe the
surface with a soft, damp cloth.
For more thorough cleaning, wipe
the surface with a mild soap.
Maintenance and care
201

If the leather cannot be completely
cleaned using a mild soap and
water solution, the leather may
cleaned using a commercially
available cleaning product
ªTanners Preserve Leather
Cleanerº and a 3M ªType T'
scrubbing pad by using the
following steps;
The type of scrubbing pad is
very critical because the
common 3M ªScotch Briteº
green pad is too aggressive and
will damage the leather surface
²Spray a small amount of the
leather cleaner on the pad and
rub the area to be cleaned with
the pad using a circular motion.
Only clean 1/4 of the area at a
time. For heavily soiled areas,
spray the cleaner directly onto
the leather (two squirts should
be adequate) and rub with the
pad. Repeat if necessary.
²Use a soft, damp cloth to
remove the loosened dirt and
foam.
²Dry with a soft cloth.
Do not use household cleaners,
glass cleaner, alcohol solutions
or cleaner intended for vinyl,
rubber or plastics. These
products can damage the
leather.
In some instances, color or dye
transfer can occur when wet
clothing (wool, denim, leathers
or other non-colorfast
garments) comes in contact
Maintenance and care
202

with leather upholstery. If this
occurs, the leather should be
cleaned immediately to avoid
permanent staining.
ªTanners Preserve Leather
Cleanerº (product number AS-300)
is available from ªFirst Brandsº by
calling 1±800±726±1001. This
product may also be available at
many local automotive after
market stores.
3M ªType Tº Clean And Finish
Scrubbing Pads (UPC
04011±01276) are available
through your local 3M distributor.
Call 1±800±742±9649 for the
nearest distributor in your area.
PART NUMBER PART NAME
(Obtain Locally) Tanners Preserve Leather Cleaner
(Obtain Locally) 3M9Type T9Clean and Finish
Scrubbing Pads
Woodtone trim
Wipe stains with a soft cloth and a
multi-purpose cleaning solution.
Inside windows
Use glass cleaner for the inside
windows if they become fogged.
Cleaning mirrors
Do not clean your mirrors with a
dry cloth or abrasive materials. Use
a soft cloth and mild detergent and
water. Be careful when removing
ice from outside mirrors because
you may damage the reflective
surface.
Maintenance and care
203

MOTORCRAFT PART NUMBERS
Component 4.0L SOHC engine 5.0L engine
Air filter FA-1658 FA-1658
Fuel filter FG-872 FG-872
Battery (standard) BXT-65-650 BXT-65-650
Battery (optional) - BXT-65-850
Oil filter FL-1A FL-820S
PCV valve EV-225 EV-152
Spark plugs* AGRF-22P AWSF-32EE
* Refer to Vehicle Emissions Control Information (VECI) decal for
spark plug gap information.
REFILL CAPACITIES
Fluid Ford Part
NameApplication
Capacity
Engine oil
(including filter
change)Motorcraft 5W30
Super Premium
Motor OilAll
4.7L
(5.0 quarts)
Brake fluid Ford High
Performance
DOT 3 Brake
FluidAll
Fill to the MAX
line on reservoir
Power steering
fluidMotorcraft
MERCONtAT FAll Fill to line on
reservoir
Capacities and specifications
204

Fluid Ford Part
NameApplication
Capacity
Transmission
fluidMotorcraft
MERCONtV
AT F4R70W
Automatic with
5.0L engine
(AWD)13.1L
(13.9 quarts)
5R55E
Automatic with
4.0L SOHC
engine (4x2)9.25L
(9.75 quarts)
5R55E
Automatic with
4.0L SOHC
engine (4x4)9.55L
(10.0 quarts)
Transfer case Motorcraft
MERCONtAT FAWD 1.25L
(1.3 quarts)
4WD 1.4L
(1.5 quarts)
Engine coolant Ford Premium
Cooling System
Fluid4.0L engine 7.4L
(7.8 quarts)
5.0L engine 12.1L
(12.8 quarts)
Front axle fluid Motorcraft
80W90 Axle
LubricantAll
1.7L (3.5 pints)
Rear axle
fluid
1,2,3,4Motorcraft SAE
80W90 Axle
LubricantVehicles with
conventional
axles
2.9-3.1L
(5.50-5.80 pints) Motorcraft SAE
75W140 High
Performance
Synthetic Rear
Axle LubricantRefer to
footnotes 2 and
3
Capacities and specifications
205

Fluid Ford Part
NameApplication
Capacity
Windshield
washer fluidUltra-Clear
Windshield
ConcentrateAll vehicles
2.6L
(2.7 quarts)
1Fill to 6 mm to 14 mm (1/4 inch
to 9/16 inch) below bottom of fill
hole.
2Your vehicle's rear axle is
equipped with synthetic rear axle
lubricant. Rear axles containing
synthetic lubricant are lubricated
for life. These lubricants are not to
be checked or changed unless a
leak is suspected, service required
or the axle assembly has been
submerged in water. The axle
lubricant should be changed any
time the axle has been submerged
in water. For Traction±Lok add
118 ml (4 oz.) of additive friction
modifier C8AZ±19B546±A, Ford
specification EST-M2C118±A, to
your rear axle whenever the
lubricant is changed.
3Vehicles equipped with 4.0L
SOHC engines and 3.73 or 4.10
rear axle ratios or 5.0L engines
require synthetic rear axle
lubricant. Rear axles containing
synthetic lubricant are lubricated
for life. These lubricants are not to
be checked or changed unless a
leak is suspected, service required
or the axle assembly has been
submerged in water. The axle
lubricant should be changed any
time the axle has been submerged
in water. For Traction-Lok rear
Capacities and specifications
206

axles, add 118 ml (4 oz.) of
additive friction modifier
C8AZ-19B546-A, Ford specification
EST-M2C118±A, whenever the
lubricant is changed.
4Refer to your ªService Guideº for
axle fluid change intervals.
LUBRICANT SPECIFICATIONS
FluidFord part
name or
equivalentFord part
numberFord
specification
Windshield
washer fluid
reservoirFord Ultra-Clear
Windshield
Washer
ConcentrateC9AZ-19550-AA
OR -BAESR-M17P5-A
Body hinges,
latches, door
stricker plates
and rotors, seat
tracks, fuel filler
door hinge and
spring, hood
latch, auxiliary
latchMulti-Purpose
GreaseD7AZ-19584-AA
OR
DOAZ-19584-AAESR-M1C159-A
AND
ESB-M1C93-B
Driveshaft, slip
spline, universal
jointsPremium Long
Life GreaseXG-1-C or K ESA-M1C75-B
Engine coolantFord Premium
Cooling System
FluidE2FZ-19549-AA ESE-M97B44-A
Engine oilMotorcraft 5W30
Super Premium
Motor OilXO-5W30-QSPWSS-M2C153-G
with API
Certification
Mark
Capacities and specifications
207

FluidFord part
name or
equivalentFord part
numberFord
specification
Automatic
transmission
(4R70W)Motorcraft
MERCONtV
AT FXT-5-QM MERCONtV
Automatic
transmission
(5R55E)Motorcraft
MERCONtV
AT FXT-5-QM MERCONtV
Power steering
reservoirMotorcraft
MERCONtAT FXT-2-QDX MERCONt
Ford
conventional and
traction lok rear
axlesRefer to
footnotes 1, 2
and 3Refer to
footnotes 1, 2
and 3o footnotes 1, 2
and 3
Front axle 4x4 Gear Oil F1TZ-19580-A WSL-M2C191-A
Transfer caseMotorcraft
MERCONtAT FXT-2-QDX MERCONt
Transfer case
Front Output
Slip ShaftPremium
Long-Life GreaseXG-1-G or K ESA-M1C75-B
14.0L vehicles with conventional
and Traction-lok rear axles are
filled with Motorcraft SAE 80W90
Premium Rear Axle Lube, part
number XY-80W90±QL, Ford
specification WSP-M2C197±A.
24.0L vehicles with limited slip
differentials and all 5.0L
applications use rear axles that are
filled with Motorcraft SAE 75W140
High Performance Synthetic Rear
Axle Lube, part number
F1TZ-19580±B, Ford specification
WSL-M2C192±A.
34.0L vehicles with limited slip
differentials and all 5.0L
Capacities and specifications
208

applications must add 118ml
(4 oz.) of additive friction modifier
C8AZ-19B546±A, Ford specification
EST-M2C118±A to the rear axle
whenever the axle has been
serviced.
ENGINE DATA
Engine 5.0L engine 4.0L SOHC engine
Cubic inches 302 245
Horsepower 215 @ 4200 rpm 205 @ 5000 rpm
Torque 288 lbs.ft. @ 3300 rpm 250 lb. ft. @ 3000 rpm
Required fuel grade 87 octane 87 Octane
Firing order 1-3-7-2-6-5-4-8 1-4-2-5-3-6
Spark plug gap 1.3 mm-1.4 mm
(0.052-.056 inch)1.3 mm-1.4 mm
(0.052-.056 inch)
Ignition system EDIS EDIS
Compression ratio 9.0:1 9.7:1
VEHICLE DIMENSIONS
Dimensions mm (in.)
(1) Overall length 4 788 (188.5)
(2) Overall width 1 783 (70.2)
(3) Maximum height 1 725 (67.9)
(4) Wheelbase 2 835 (111.6)
(5) Front track/ rear 1 486/1487 (58.5/58.5)
Capacities and specifications
209

4
1
3
5
2
Capacities and specifications
210