Mercury Mountaineer 1998 s Workshop Manual

that the anti-theft system is not
armed, the ignition is OFF and all
vehicle doors and liftgate window
are closed.
1. Enter the 5 digit entry code.
2. Press and release the 3/4 control
while holding the 7/8 control.
3. Release the 7/8 control.
The horn will chirp once if
autolock was deactivated or twice
(one short and one long chirp) if
autolock was activated.
To reactivate autolock, repeat
steps 1 through 4.
Autolock can also be activated or
deactivated using the following
procedure:
You must complete steps 1 through
5 within 30 seconds or the
procedure will have to be
repeated. If the procedure needs
to be repeated, you must wait
30 seconds.
1. Turn the ignition key to ON.
2. Press the power door unlock
control three times.
3. Turn the ignition key from ON
to OFF.
4. Press the power door unlock
control three times.
5. Turn the ignition key back to
ON. The doors will lock and
unlock.
123
45678
90
Controls and features
51

6. Press the power door unlock
switch. The horn will chirp once
upon successful toggling of the
Autolock feature.
7. Turn ignition to OFF. The horn
will chirp to confirm procedure is
complete.
Keyless entry system
(if equipped)
With the keyless entry keypad, you
can:
²lock or unlock the vehicle doors
without using the key
²arm and disarm the perimeter
alarm system (if equipped)
²activate/deactivate the autolock
feature
See alsoRemote entry systemand
Perimeter alarm systemin this
chapter for more information.
Your vehicle has a factory-set 5
digit code that operates the
keyless entry system. You can also
program your own 5 digit personal
entry code.
The factory-set code is located:
²on the owner's wallet card in the
glove compartment
²taped to the computer module
When pressing the controls on the
keyless entry keypad, press the
middle of the buttons to ensure a
good activation.
123
45678
90
Controls and features
52

Programming your own
personal entry code
1. Enter the factory-set code
(keypad will illuminate when
pressed).
2. Press the 1/2 control within five
seconds of step 1.
3. Enter your personal 5 digit
code. Enter each digit within five
seconds of the previous one.
Do not set a code that includes
five of the same number or
presents them in sequential order.
Thieves can easily figure out these
types of codes.
Your personal code does not
replace the permanent code that
the dealership gave you. You can
use either code to unlock your
vehicle. If a second personal code
is entered, the module will erase
the first personal code in favor of
the new code.
If you wish to erase your personal
code, use the following
instructions:
123
45678
90
Controls and features
53

Erasing personal code
1. Enter the factory-set code.
2. Press 1/2 within five seconds of
step one.
3. Press the 7/8 and 9/0 controls at
the same time within five seconds
of step two.
The system will now only respond
to the factory-set code.
Unlocking the doors with the
keyless entry system
To unlock the driver's door, enter
either the factory-set code or
personal code (each digit pressed
within 5 seconds of the prior
digit). The interior lamps will
illuminate.
To unlock all doors, enter the
factory-set code or personal code
(driver door unlocks) and press
the 3/4 control within 5 seconds.
Locking the doors with the
keyless entry system
To lock all the doors, press 7/8 and
9/0 at the same time. It is not
necessary to first enter the keypad
code.
This will arm your perimeter alarm
system (if equipped). Refer to
Perimeter alarm systemin this
chapter for more information.
123
45678
90
123
45678
90
123
45678
90
Controls and features
54

Operating your perimeter alarm
system (if equipped) from the
keyless entry pad
The keyless entry system arms by
pressing 7/8 and 9/0.
To disarm or reset a triggered
alarm, enter the five digit code.
All doors must be fully closed for
the alarm system to arm. Refer to
thePerimeter alarm system
section, if equipped, in this chapter
for more details.
PERIMETER ALARM SYSTEM
Arming the system
When armed, this system will help
protect your vehicle from
unauthorized entry. When
unauthorized entry occurs, the
system will flash the headlamps,
parking lamps and the theft
indicator lamp and will chirp the
horn.
The system is ready to arm
whenever the ignition is turned
OFF. Any of the following actions
will prearm the alarm system:
²Press the remote entry lock
control
²Open a door and press the
power door lock control to lock
the doors123
45678
90
Controls and features
55

²Pressing 7/8 and 9/0 on the
keyless entry pad at the same
time to lock the doors (doors
opened or closed).
If a door is open, the system is
prearmed and is waiting for the
door to close. The theft indicator
on the instrument cluster will be
lit continuously when the system is
prearmed.
Once the doors are closed, the
system will arm in 30 seconds.
When you press the lock control
twice within 5 seconds, the horn
will chirp once to let you know
that the system is armed.
If the doors are not closed and you
press the remote entry transmitter
twice to confirm the doors are
locked, the horn will chirp twice to
warn you that the system is not
arming.
Disarming the system
You can disarm the system by any
of the following actions:123
45678
90
Controls and features
56

²Unlock the doors by using your
remote entry transmitter.
²Unlock the doors with a key.
Turn the key full travel (toward
the front of the vehicle) to make
sure the alarm disarms.
²Unlock the doors by using your
keyless entry keypad.
²Turn ignition to ACC or ON.
²Press the panic control on the
remote entry transmitter. This
will disarm the system only if
the alarm is sounding.
SecuriLockYanti-theft system
The SecuriLockyanti-theft system
provides an advanced level of
vehicle theft protection. Your
vehicle's engine can only be started
with the two special SecuriLocky
electronically coded keys provided
with your vehicle. Each time you
start your vehicle, the
123
45678
90
Controls and features
57

SecuriLockykey is read by the
SecuriLockyanti-theft system. If
the SecuriLockykey identification
code matches the code stored in
the SecuriLockyanti-theft system,
the vehicle's engine is allowed to
start. If the SecuriLockykey
identification code does not match
the code stored in the system or if
a SecuriLockykey is not detected
(vehicle theft situation), the
vehicle's engine will not operate.
Spare SecuriLockykeys can be
purchased from your dealership
and programmed to your
SecuriLockyanti-theft system.
Refer toProgramming spare
SecuriLockykeysfor more
information.
If one or both of your SecuriLocky
keys are lost or stolen and you
want to ensure the lost or stolen
key will not operate your vehicle,
bring your vehicle and all available
SecuriLockykeys to your
dealership for reinitialization.
Theft indicator
The theft indicator on the
instrument cluster will operate as
follows:
²When the ignition is OFF, the
theft indicator will flash briefly
every 2 seconds to indicate the
SecuriLockysystem is
protecting your vehicle.
²When the ignition is turned to
RUN or START, the theft
indicator will light for 3 seconds
and then go out. If the theft
Controls and features
58

indicator stays on for an
extended period of time or
flashes rapidly, have the system
serviced by your dealership or a
qualified technician.
Programming spare
SecuriLock
Ykeys
Spare SecuriLockykeys can be
purchased from your dealership
and programmed to your
SecuriLockyanti-theft system (up
to a total of 8 keys). Your
dealership can program your new
SecuriLockykey(s) to your
vehicle or you can do it yourself
using the following simple
procedure. To program a new
SecuriLockykey yourself, you will
need two previously programmed
SecuriLockykeys (keys that
already operate your vehicle's
engine). If two previously
programmed SecuriLockykeys are
not available (one or both of your
original keys were lost or stolen),
you must bring your vehicle to
your dealership to have the spare
SecuriLockykey(s) programmed.
Procedure to program spare
SecuriLock
Ykeys to your
vehicle
New SecuriLockykeys must have
the correct mechanical key cut for
your vehicle.
Conventional (non-SecuriLocky)
keyscannotbe programmed to
your vehicle.
You will need to have two
previously programmed
Controls and features
59

SecuriLockykeys and the new
unprogrammed SecuriLockykey
readily accessible for the
procedure. Please read and
understand the entire procedure
before you begin.
1. Insert the first previously
programmed SecuriLockykey into
the ignition switch and turn the
ignition from OFF to RUN
(maintain ignition in RUN for at
least one second).
2. Turn ignition to OFF and
remove the first SecuriLockykey
from the ignition switch.
3. Within five seconds of turning
the ignition to OFF, insert the
second previously programmed
SecuriLockykey into the ignition
switch and turn the ignition from
OFF to RUN (maintain ignition in
RUN for at least one second but no
more than 5 seconds).
4. Turn the ignition to OFF and
remove the second SecuriLocky
key from the ignition switch.
5. Within 10 seconds of turning the
ignition to OFF, insert the
unprogrammed SecuriLockykey
(new key) into the ignition switch
and turn the ignition from OFF to
RUN (maintain ignition switch in
RUN for at least one second). This
step will program your new
SecuriLockykey.
6. If it is desired to program
additional SecuriLockykey(s),
repeat this procedure from step 1.
Controls and features
60