engine Mercury Villager 1996 s Owner's Guide

242
*
[DR12100(ALL)01/93]
The load capacities of your vehicle's tires affect the GVWR or
GAWR limitations. Using replacement tires with a higher weight
limit than the originals does not increase GVWR or GAWR.
Using lower capacity replacement tires may lower GVWR and
GAWR limitations.
*
[DR12200(ALL)02/95]
RWARNING
If the GVWR or the GAWR specified on the Safety
Compliance Certification Label is exceeded, your vehicle
may be damaged or you may lose control and injure
someone.
*
[DR12300(ALL)01/93]
Vehicle/Trailer Loads
[DR12400(ALL)07/93]
Your vehicle may tow a Class I trailer up to 2,000 lbs. (907 kg)
provided the Gross Vehicle Weight (GVW) is less than the
GVWR shown on the Safety Compliance Certification Label.
With the optional trailer tow package, your vehicle can tow a
trailer up to 3,500 lbs. (1,588 kg).
*
[DR12500(ALL)02/95]
Trailer Towing (may require trailer tow option package)
*
[DR12600(ALL)01/93]
Towing a trailer puts an additional load on your vehicle's
engine, transaxle, axle, brakes, tires and suspension. For your
safety and for the good of your vehicle, use the right equipment
for the type of trailer you tow.
*
[DR12700(ALL)02/92]
n
Stay within the load limits when you tow.
*
[DR12800(ALL)01/93]
n
Carefully and thoroughly prepare your vehicle for towing,
making sure to use the right equipment and to attach it
properly. SeePreparing to Towin this section.
*
[DR12900(ALL)01/93]
n
Use extra caution when driving your vehicle while you tow.
SeeDriving While You Towin this section.
*
[DR13000(ALL)01/93]
n
Service your vehicle more frequently if you tow a trailer. See
Servicing Your Vehicle if You Towin this section.
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996

250
*
[DR18600(ALL)06/95]
RWARNING
Towing trailers beyond the maximum recommended
gross trailer weight exceeds the limits of the vehicle and
could result in engine damage, transaxle/axle damage,
structural damage, loss of control, and personal injury.
*
[DR18700(ALL)01/95]
Preparing to Tow
*
[DR18800(ALL)05/93]
For your safety and for the good of your vehicle, use the right
equipment for the type of trailer you tow. Also, make sure that
all towing equipment is properly attached to your vehicle. If
you are not certain that you are using the right equipment in
the proper manner, see your dealer or a reliable trailer dealer.
%*
[DR18900(ALL)01/93]
Hitches
*
[DR19000(ALL)01/93]
For towing trailers up to 2,000 lbs. (907 kg), use a good
weight-carrying hitch and hitch ball which uniformly distributes
the trailer tongue load through the underbody structure.
[DR19100(ALL)02/94]
An optional trailer towing package is available for towing
trailers up to 3,500 lbs. (1587 kg). Use a frame-mounted weight
distributing hitch for trailers over 2,000 lbs. (907 kg).
*
[DR19200(ALL)01/93]
Do not use single clamp bumper hitches or hitches that attach
to the axle.
*
[DR19300(ALL)01/93]
Whenever a trailer hitch and hardware are removed, make sure
all mounting holes in the underbody are properly sealed to
prevent exhaust fumes from entering the vehicle.
*
[DR19400(ALL)04/94]
Safety chains
*
[DR19500(ALL)01/93]
Always use safety chains between your vehicle and trailer.
Cross chains under the trailer tongue and allow slack for
turning corners. Connect safety chains to the vehicle frame or
hook retainers.Never attach chains to the bumper.
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996

Driving Your Villager
253
*
[DR21300(ALL)01/93]
Allow more room for stopping with a trailer attached. Trailer
brakes should be applied first, whether manually or
automatically controlled, when approaching a stop.
*
[DR21400(ALL)01/93]
For an easy-to-operate vehicle/trailer combination, the trailer
tongue load should be approximately 10-15% of the loaded
trailer weight.
*
[DR21500(ALL)02/94]
Make a thorough check of your equipment before starting out
on the road. After you have traveled about 50 miles (80 km),
stop in a protected area and double-check your hitch and
electrical connections. Also check trailer wheel lug nuts for
tightness.
[DR21600(ALL)01/93]
When stopped in traffic for long periods of time in hot weather,
place the gearshift selector lever in Park (P) to increase the
engine idle speed. This aids in engine cooling and air
conditioner efficiency. If the engine overheats, press the air
intake button to select the fresh air position to stop the air
conditioner compressor. Increase the engine speed for a short
time.
*
[DR21700(ALL)01/93]
Vehicles with trailers should not be parked on a grade.
However, if you must park on a grade, place wheel chocks
under the trailer's wheels as follows:
[DR21800(ALL)04/94]1.
Apply the main brake pedal with your foot and hold it.
*
[DR21900(ALL)11/93]2.
Have another person place the wheel chocks under the
trailer wheels.
[DR22000(ALL)04/94]3.
With the chocks in place, release the brake pedal, making
sure the chocks are holding.
[DR22100(ALL)04/94]4.
Apply the parking brake by pressing the main brake pedal
down firmly with your right foot while depressing the
parking brake pedal with your left foot.
*
[DR22200(ALL)06/95]5.
Shift the gearshift lever into P (Park).
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996

254
*
[DR22300(ALL)01/93]
To start, after being parked on a grade:
[DR22400(ALL)04/94]1.
Apply the main brake pedal with your foot and hold it.
*
[DR22500(ALL)11/93]2.
Start the engine.
*
[DR22600(ALL)11/93]3.
Shift the gearshift lever into gear and release the parking
brake.
[DR22700(ALL)04/94]4.
Release the main brake pedal and move the vehicle uphill to
free the wheel chocks.
[DR22800(ALL)04/94]5.
Apply the main brake pedal and hold while another person
retrieves the chocks.
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996

255
Roadside Emergencies
[RE00700(ALL)03/94]
Jump-Starting Your Battery
*
[RE00800(ALL)01/93]
Your vehicle's battery may discharge if you leave the lights or
any electrical equipment on after you turn the engine off. If this
happens, you may be able to jump-start from a booster battery
to start your vehicle.
*
[RE00900(ALL)02/95]
RWARNING
The gases around the battery can explode if exposed to
flames, sparks, or lit cigarettes. An explosion could result
in injury or vehicle damage.
*
[RE01000(ALL)02/95]
RWARNING
To protect yourself when charging a battery, always
shield your face and eyes. Make sure that you can
breathe fresh air.
%*
[RE01100(ALL)05/95]
RWARNING
Applying too much pressure on the ends when lifting a
battery could cause acid to spill. Lift the battery with a
carrier or with your hands on the opposite corners.
%*
[RE01200(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns skin, eyes,
and clothing.
*
[RE01210(ALL)06/95]
If the acid touches someone's skin, eyes, or clothing,
immediately flush the area with water for at least 15 minutes. If
someone swallows the acid, have him or her drink lots of milk
or water first, then Milk of Magnesia, a beaten egg, or vegetable
oil. Call a doctor immediately.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

256
%*
[RE01300(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns skin, eyes,
and clothing.
*
[RE01400(ALL)03/95]
To avoid damaging your vehicle or your battery, and to avoid
injury to yourself, follow these directions for preparing your
vehicle to jump-start and connecting the jumper cables in the
order they are given. If in doubt, call for road service.
*
[RE01500(ALL)03/95]
Preparing Your Vehicle
*
[RE01600(ALL)03/95]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[RE01700(ALL)03/95]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[RE01800(ALL)04/95]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[RE01900(ALL)03/95]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[RE02000(ALL)01/93]5.
Turn on the heater blower in both vehicles. Turn off all other
switches and lights in both vehicles to prevent possible
damage to either vehicle's electrical systems.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

Roadside Emergencies
257
%*
[RE02100(ALL)05/95]
Connecting the jumper cables
*
[RE02200(ALL)03/95]1.
Connect one end of the first jumper cable to the positive (+)
terminal of the discharged battery. (You can connect either
jumper cable to the positive (+) terminal, as long as you use
the same cable for both positive terminals.) Most jumper
cables have a red cable and a black cable. The red cable is
generally used for the positive terminals and the black for
the negative ones.
*
[RE02300(ALL)04/95]2.
Connect the other end of the first cable to the positive (+)
terminal of the booster battery.
*
[RE02400(ALL)05/95]3.
Connect one end of the second cable to the negative (s)
terminal of the booster battery Ð NOT to the discharged
battery.
*
[RE02500(ALL)04/95]4.
Connect the other end of the second cable to a good metallic
surface on the engine or frame of the disabled vehicle.
*
[RE02600(ALL)05/95]
RWARNING
Do not connect the end of the second cable to the
negative (-) terminal of the battery to be jumped. A spark
may cause an explosion of the gases that surround the
battery.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

Roadside Emergencies
259
*
[RE02800(ALL)03/95]
Jump-Starting
*
[RE02900(ALL)03/95]1.
Make sure that the jumper cables are not in the way of
moving engine parts, then start the booster vehicle. Run the
engine at a moderate speed.
*
[RE03000(ALL)03/95]2.
Let the discharged battery charge for a few minutes and then
start the disabled vehicle. It may take a couple of tries before
the vehicle starts. If the vehicle does not start after several
attempts, there may be a different problem.
*
[RE03100(ALL)03/95]3.
When both vehicles are running, let them idle for a few
minutes to charge the discharged battery.
*
[RE03200(ALL)03/95]
Removing jumper cables
*
[RE03300(ALL)03/95]1.
Always remove the jumper cables in the reverse order.
Remove the negative (s) end of the jumper cable from the
metallic surface on the engine or frame of the disabled
vehicle.
*
[RE03400(ALL)05/95]2.
Remove the negative (s) cable from the booster battery.
*
[RE03500(ALL)06/95]3.
Remove the positive (+) cable from the booster battery.
*
[RE03600(ALL)05/95]4.
Remove the other end of the positive (+) cable from the
discharged battery.
[RE03750(ALL)02/95]
If you need to replace your battery, seeBatteryin theServicing
Your Villagerchapter.
*
[RE03800(ALL)01/93]
Changing a Flat Tire
*
[RE03900(ALL)01/95]
If you get a flat tire while you are driving, do not apply the
brake heavily. Instead, gradually decrease the speed. Hold the
steering wheel firmly and slowly move to a safe place on the
side of the road. Park on a level spot, turn off the ignition, set
the parking brake, and turn on the hazard flashers.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

Roadside Emergencies
269
[RE08550(ALL)05/95]
RWARNING
Do not jack on the running board.
*
[RE08600(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
*
[RE08700(ALL)05/95]
RWARNING
To lessen the risk of personal injury, do not put any part
of your body under the vehicle while changing a tire. Do
not start the engine when your vehicle is on the jack.
The jack is only meant for changing the tire.
*
[RE08800(ALL)05/94]
RWARNING
Never raise your vehicle by using a bumper jack. The
bumper could be damaged or the jack could slip and you
could be injured.
[RE08900(ALL)01/93]6.
Insert the jack handle into the jack, and then slide the
tapered end of the jack handle through one of the slots in
the lug nut wrench. All of these tools are needed to jack up
a vehicle.
[RE09000(ALL)01/93]
NOTE: If Ford Accessory Running Boards have been
installed, use the jack adapters supplied with the
running boards as described on the inside of the jack
storage area cover.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996

Roadside Emergencies
273
*
[RE10800(ALL)01/93]
Fuel Pump Shut-Off Switch
*
[RE10900(ALL)03/95]
If the engine cranks but does not start or if you have had a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device that stops the fuel
pump when your vehicle has been involved in a substantial jolt.
*
[RE11000(ALL)01/95]
For information on how to check and reset the fuel pump
shut-off switch, seeFuel pump shut-off switchin the Index.
*
[RE11150(ALL)05/95]
Towing Your Vehicle
[RE11175(ALL)04/95]
If you need to have your vehicle towed, contact a professional
towing service or, if you are a member, your roadside assistance
center.
[RE11200(ALL)07/95]
DO NOT TOW YOUR VILLAGER WITH SLINGBELT
EQUIPMENT. Ford Motor Company has not developed or
approved a T-hook sling-type procedure. Use wheel lift or
flatbed equipment.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996