brake light MITSUBISHI 3000GT 1991 User Guide

23-1
AUTOMATIC
TRANSAXLE
CONTENTSMZJAA- _
ANNULUS GEAR AND TRANSFER DRIVE GEARTransmission Fluid Level Inspection................................46SET................................................................................................
102Transmission Fluid Replacement........................................
46
DIFFERENTIAL........................................................................104SPECIAL TOOLS........................................................................
16
:......................................... 12IEND CLUTCH ASSEMBLY....................................................99SPECIFICATIONS..........................
FRONT CLUTCH ASSEMBLY................................................95
GENERAL INFORMATlON....................................................2
KICKDOWN SERVO................................................................
107
LOW-REVERSE BRAKE............................................................
107
OIL PUMP....................................................................................93
PLANETARY GEAR................................................................
100
REAR CLUTCH ASSEMBLY....................................................97
SELECTOR LEVER ASSEMBLY............................................58
SERVICE ADJUSTMENT PROCEDURES............................46
Accelerator Switch
Inspection and Adjustment................
50Drive Shaft Oil Seals Replacement....................................
52Inhibitor Switch and Control Cable Adjustment................
52Key Interlock Mechanism Check........................................50KickdownServo Adjustment................................................
47Line Pressure Adjustment....................................................
48Reducing Pressure Adjustment........................................
49Selector Lever Operation Check........................................
50Shift Lock Mechanism Check............................................51Speedometer Cable Replacement....................................53
General Specifications........................................................12Lubricants............................................................................15Service Specifications........................................................12Spacer and Snap Ring........................................................13Valve Body Spring Identification Chart............................13
SPEEDOMETER DRIVEN GEAR ASSEMBLY....................106
TRANSAXLE ASSEMBLY........................................................62
TRANSAXLE CONTROL*........................................................54
TRANSAXLE OIL COOLER, HOSES, TUBES
....................66
TRANSFER SHAFT....................................................................92
TROUBLESHOOTING............................................................
19
A/T Safety-lock System Troubleshooting........................44Converter Stall Test............................................................
43
Diagnosis and Test
................................................................
22
Element in Use at Each Position of Selector Lever........31Inspection
of ControlSystem............................................
28Inspection of Electronic Control System Components....32Oil Pressure Tests................................................................
39ShiftPatterns....................................................................
31,42Troubleshooting Guide........................................................
20
VALVE BODY. . . .._._.................................................................... 108
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3668GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to beremoved/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead topersonal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
(3) MlTSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the
ISRS or any SRS-related component.

AUTOMATIC TRANSAXLE - Service Adiustment Procedures23-51
D9N007SPush button
II
2.Check to be sure that, under the following conditions, the
selector lever can be moved from the “P” position to any
other position.
Press the button a few times and check to be sure that the
selector lever moves smoothly.
Ignition key position: “ACC”
Brake pedal: Depressed
Button
: Pressed
3.Check to be sure that, at all positions of the selector lever
(other than “P”), the ignition key cannot be turned to the
“LOCK” position.
Check to be sure that the ignition key smoothly turns to the
“LOCK” position when the selector lever is then set to the
“P” position and the button is released.
4. If above are not checked okay, adjust key interlock cable
mechanism as follows.
(1) Remove front console assembly.
(2) Place selector lever into “P” position.
(3) Turn ignition key to the “LOCK” position.
(4) Loosen nut that secures key interlock cable.
(5) Lightly pressing lock cam A in the direction of arrow,
lightly push key interlock cable to take up slack and
tighten nut to secure key interlock cable.
(6) Reinstall front console assembly.
SHIFT LOCK MECHANISM CHECKMZ3FVAC
1.
2.
3.
4.Check to be sure that, under the following
condi,tions, the
selector lever cannot be moved from the “P” position to
any other position.
Ignition key position: “ACC”
Brake pedal: Not depressed
Button: PressedCheck to be sure that, under the following conditions, the
selector lever can be moved smoothly from the “P”
position to other position.
Ignition key position: “ACC”
Brake pedal : Depressed
Button: PressedCheck to be sure that, under the following conditions, the
selector lever can be moved smoothly from the “R”
position to the “P” position.
Ignition key position: “ACC”
Brake pedal: Released
Button: PressedIf a malfunction is discovered when following the above
checking procedures, either adjust or check the shift lock
cable mechanism. (Refer to
P.23-56.)
TSB Revision

23-56AUTOMATIC TRANSAXLE - Transaxle ControlOQPOOQQ
09FOO5
INSPECTIONM231CAMl Check the control cable for function and for damage.
lCheck the outer cable (key interlock cable, shift lock cable)
’for damage and spring for breakage and tension.~J
lCheck the inner cable (key interlock cable, shift lock cable)
for extension.
REVERSE
(R) POSITION ALARM BUZZER
Check that the buzzer sounds when battery voltage is applied
across terminals.
SERVICE POINTS OF INSTALLATIONM231DAW
19. CONNECTION OF SHIFT LOCK CABLE (BRAKE PEDAL
SIDE)Connect the shift lock cable so that its threads measure
about 4 mm
(.16 in.).
CautionDo not change the routing of shift lock cable to the
selector lever assembly.
16. INSTALLATION OF SLIDE LEVER / 15. KEY INTERLOCK
CABLE (STEERING LOCK ASSEMBLY SIDE) / 14. CAM
LEVER(1) Place the ignition key at the “LOCK” position or keep it
removed.
(2) Install the slide lever, key interlock cable, and cam lever
to the steering lock assembly as shown.
Caution
Do not change the routing of key interlock cable tothe selector lever assembly.
5. CONNECTION OF TRANSAXLE CONTROL CABLE
(SELECTOR LEVER ASSEMBLY SIDE)Connect the transaxle control cable, then make the follow-
ing adjustment.
(1) Place the selector lever in “N” position.
(2) Loosen the nut and slightly pull the transaxle control
cable in the direction of the arrow; then, tighten the nut.
4.CONNECTION OF SHIFT LOCK CABLE (SELECTOR LEV-
ER ASSEMBLY SIDE)(1) Place the selector lever in “P” position.
(2) Disconnect the key interlock cable from the selector
lever assembly side.
(3) Turn the lock cam B counterclockwise (arrow
0) to
move the set lever upward (arrow
0)._.-(4) Frt the cutout in set lever to the jock pm ot lock cam B. u
TSB Revision

26-12FRONT AXLE - Drive Shaft
-01
M 8990635-0112R0258
llA0286i
llN0027
SERVICE POINTS OF REMOVALM26QBAY2. REMOVAL OF DRIVE SHAFT NUT
Loosen the drive shaft nut while the vehicle is on the floor
with the brakes applied.
Caution
Do not apply vehicle load to the wheel bearing loosingthe drive shaft nut. If, however, vehicle load must be
applied to the bearing in moving the vehicle, temporari-
ly secure the wheel bearing by using the special tools,
MB990998-01, etc.
3. DISCONNECTION OF LOWER ARM BALL JOINT
Using the special tool, disconnect the lower arm ball joint
from the knuckle.
Caution1. Be sure to tie the cord of the special tool to the
nearby part.2. Loosen the nut but do not remove it.
5. DISCONNECTION OF TIE ROD END
Using the special tool, disconnect the tie rod end from the
knuckle.
Caution1. Be sure to tie the cord of the special tool to the
nearby part.
2. Loosen the nut but do not remove it.
7. REMOVAL OF DRIVE SHAFT AND INNER SHAFT
ASSEMBLY (L.H.)
/ 8. DRIVE SHAFT (R.H.)
(I) Using the special tool, push out the drive shaft and inner
shaft assembly (L.H.) or the drive shaft
(R.H.) from the
hub.(2) If the inner shaft is hard to remove from the transaxle,
strike the center bearing bracket lightly with a plastic
hammer.
‘\
L+i
TSB Revision

I,
ELECTRONIC CONTROL SUSPENSION (ECS) - ;;~i%:~ustment339-15
Item No.Check
PointCheck ConditionSoundness Determination Value
24
Check by actually operating
vehicle.Speedometer indication and
MUT indication coincide.
26
61
62
63
64Vehicle
speed
sensorstop
lightswitch
F.R.actuator
F.L.actuator
R.R.actuator
R.L.actuatorDepress brake pedal.
ON
Do not depress brake pedal.OFF
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD4. ACTUATOR CHECK
(I) Using the MUT, force-drive the actuator and fix the damping force changeover.
(2) Check service data (Item No. 61 through 64) to verify that the actuator has been force-driven.
NOTE
lAll of the four actuators in the shock absorbers are simultaneously changed over by forced drive.
lThe damping force changed over and fixed by forced drive is cleared by the following three conditions.1. Ignition switch OFF
2. Vehicle speed 3 km/h (1.9 mph) or more
3. MUT disconnected
Actuator Check List
Item No.Check Point
Check ConditionMUT Service Data Item
No. 61 - 64 Indicated
01Damping force SOFT
03Damping force MEDIUM
04Damping force HARD
Vehicle in stationary
conditionSOFT
MEDIUM
HARD
i
TSB Revision

33B-20 ELECTRONIC CONTROL SUSPENSION (ECS)-llwmtk Positkm .semor I stop tight switch I POriticm DetsctionSWitEh 1 DPmping Force changeover Acluatc., / EC3 Indii.ar l.igil*
THROTTLE POSITION SENSORM33ZKA6
INSPECTION AND ADJUSTMENTIRefer to GROUP 13
- Fuel System.‘lJ ’
STOP LIGHT SWITCHM33ZCAC
To remove or mount the stop light switch, refer to GROUP 35 -
Brake Pedal.
INSPECTIONRefer to GROUP 35
- Brake Pedal.
POSITION DETECTION SWITCH and
DAMPING FORCE CHANGEOVER
ACTUATORM33ZCAD
To remove or mount the position detection switch and dampingforce changeover actuator, refer to GROUP 33A
- Strut LJAssembly and GROUP 34
- Shock Absorber Assembly.
CautionThe position detection switch and damping force
changeover actuator are built into the shock absorber
assemblies of front and rear suspensions. Since they are ofthe non-disassembly type, remove or mount them in the
form of a strut assembly or shock absorber assembly.
ECS INDICATOR LIGHTM33ZLAB
To remove or mount the ECS indicator lights, refer to GROUP54
- Meters and Gauges.
TSB Revision

L,
SERVICE
BRAKES
CONTENTSM35AA..
ANTI-LOCK BRAKING SYSTEM TROUBLESHOOTING7Actuator Test Function
. . . . ..___..._____.__................................ I 2, 36Check Using Self Diagnosis Function __._.....,_._.._____........ 11, 28
Diagnosis Code Chart ..,,........,......_..................................,. 1 I, 28
How to Use the Troubleshooting Flow Chart
_____.___......._._.7Method of Clearing Diagnosis Code Memory._.,._...... 12, 30
Particular Phenomena of the Anti-lock Braking System
7Troubleshooting (ABS-AWD) ._______._.._...........................,... 26
Troubleshooting (ABS-FWD) ______.._._........_...........,.....,.....,....8
TroubleshootingMethods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
BRAKE LINE . . . . . . .._.......................................................................71
BRAKEPEDAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
ELECTRONIC CONTROL UNIT (ABS). . . . .._._..___..__._............93/
L
FRONT DISC BRAKE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73G SENSOR (AWD-ABS)’
____.____.___.__._._.................,,......,.....,.... 92
HYDRAULIC UNIT (ABS) .___.._._._._.______.............,...,,..........~ .,_____86
MASTER CYLINDER AND BRAKE BOOSTER ..__.._____.._____67SPECIFICATIONS ._....._.___.....................................
REAR DISC BRAKE . . . . . . .._..._._.___................................................81
SERVICE ADJUSTMENT PROCEDURES..___........45Bleeding48
Brake Booster Operating Inspection.
46
Brake Drum Inside Diameter Check. . .56
BrakeFluidLevelSensor Check.46
Brake Lining and Brake Drum Connection Check56Brake
Linrng Thickness Check............................................Brake Pedal Inspection and Adjustment............................Check Valve Operation Check............................................Front Brake Disc Run-out Check........................................Front Brake Disc Run-out Correction................................Front Disc Brake Pad Check and Replacement................Inspection of Front Brake Disc Thickness........................Inspection of Hydraulic Unit................................................Inspectton of Power Relay....................................................Inspection of Valve Relay and Motor Relay (ABS)............Measurement of Wheel Speed Sensor Output Voltage
Proportioning Valve Function Test
....................................Rear Brake Disc Run-out Check........................................Rear Brake Disc Run-out Correction................................Rear Brake Disc Thickness Check....................................Rear Disc Brake Pad Check and Replacement................Remedy in Case of DischargedBattery............................56
45
46
52
53
48
5258
62
62
57
47
55
55
55
53
62
SPECIAL TOOLS ..__.......___..........................................................General Specifications
........................................................Lubricants............................................................................Sealants and Adhesives........................................................Service Specifications........................................................3
TROUBLESHOOTING............................................................5
WHEEL SPEED SENSOR (ABS)............................................88
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.
i

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-7
ANTI-LOCK BRAKING SYSTEM TROUBLESHOOTlilGPARTICULAR PHENOMENA OF THE
LANTI-LOCK BRAKING SYSTEMModels equipped with the anti-lock braking system
(ABS) may exhibit one or more of the following
phenomena from time to time, but none of these
are abnormal.
(1) A pulsing feeling in the brake pedal, or vibration
of the body or the steering wheel, when the
anti-lock braking system is activated by sudden
braking or by braking on a slippery road surface.
.9ctually, this phenomenon is an indication that
the anti-lock braking system is functioning nor-
mally.(2) When the vehicle speed reaches approximately
6 km/h (4 mph) after the engine is started and
the vehicle starts off (for the first time), a
whining motor noise may be heard from the
engine compartment if the vehicle is traveling in
a quiet place, but this noise is simply the result
of a self-check being made of the anti-lock
braking system operation.
TROUBLESHOOTING METHODSProblems related to the anti-lock braking system
(ABS) can be classified into two general categories:
problems in the electrical system and those in the
Lhydraulic system.For problems in the electrical system, the
self-diagnosis function is built into the electronic control
unit (E.C.U.) causing the ABS warning light to
illuminate as a warning to the driver. In this instance,
checks can be made by using the multi-use tester
and oscilloscope.
Problems in the hydraulic system (poor braking,
etc.) can be located in the same way as for ordinary
brakes. There is, however, the necessity to check to
determine whether the problem is related to ordin-
ary brake components or to the components related
to the ABS. To make this check, use the multi-use
tester.
HOW TO USE THE TROUBLESHOOTING
FLOW CHART(1) Using the flow chart, check the ABS warning
light light-up sequence. Read the diagnosis
codes and check the condition of braking opera-
tion.
(2) Following the check chart listed in the remedy
column, perform the checks. There are [Explana-
tion] and [Hint] in each check chart. Refer to
them when troubleshooting.
NOTEECU: Electronic control unit
HU: Hydraulic unit
MUT: Multi-use tester
1 TSB Revision

35-8SERVICE BRAKES -Anti-lock Braking System Troubleshooting
TROUBLESHOOTING (ABS - FWD)Confirm condition in the following way and diagnosis accordingly.
Does the ABS warning light illuminate as described
(2) With the ignition key in the “START” position,
below up to the time the engine starts?power to the ABS ECU is interrupted and the
(1) When the ignition key is turned to the “ON”ABS warning light remains lit because the valve
position, the ABS ECU causes the ABS warningrelay is OFF.
light to flash twice in about one second (during
(3) When the ignition key is returned from the
which the valve relay self check is made) and“START” position to the “ON” position, the
then causes it to go out.ABS warning light flashes twice in about one
second (during which. the valve relay self check
-is made again) and then goes out.
ABS warning
ONlightII
-I
keyACC,
LO!: +--14A0589
Yes>CONTINUED ON NEXT PAGE
No
”
weenABS warning
1 TSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting
L’
No.Trouble condition\4
After the ignition key is turned to the
“ON” position, it blinks once and then
illuminates when it is turned to the
“START” position. When the key is
returned to the “ON” position, the light
blinks again. (Blinking with the ignition
key in the “ON” position is synchronized
with operation noise of the valve relay.)
ABSwarninglight
key ACC. L::+
Ignition
14A05931 CONTINUED FROM PREVIOUS PAGE
1Major causes
l Break in harness for ECU warning
light drive circuit
l Malfunction of ECU
Does the ABS warning light illuminate
when starting to drive the car?
iIs there one-sided braking, insufficient
>CONTINUED ON NEXT PAGEI
I
YesTrouble condition
One-sided braking
Insufficient braking force
ABS sometimes functions even when
there is no sudden braking.
(ABSoperation vibration is transmitted.)Remedy
Check, using flow
P.35-19.)Remedy
l Check HU operation and, if
l necessary, replace HU.
If HU is normal, check struc-
l
HydraJicl Malfunction in HU solenoid valvetural parts for normal
braking.
Insufficient wheel speed sensor put voltage (sensor malfunction, too
large a gap between sensor rotor,
l Malfunction of ABS ECU(Refer to
P.35-57.) and, if
necessary, replace sensor,
If tests indicate that there are
no mechanical or electricalfaiIures,replace the ECU.
TSB Revision