roof MITSUBISHI 3000GT 1991 User Guide

BODY - Door Assemblv / Door Trim and Waterproof Film42-41
Identification mark18FOO31INSPECTION
DOOR SWITCH
Operate the switch, and check the continuity between the
terminals.
Open (ON)0A
Switch”3
Depressed (OFF)
NOTEO-O indicates that there is continuity between the terminalsSERVICE POINT OF INSTALLATION
6. INSTALLATION OF DOOR CHECK STRAP
Install the door check strap with the identification mark
facing up.
PositionIdentification mark
Door (LH)WLL
Door (RH)WRR
DOOR TRIM AND WATERPROOF FILMM42MBBDREMOVAL AND INSTALLATION
Sealant:3M ATD Part No. 8625 or equivalentRemoval steps
l I)1. Clip
2. Door window regulator
3.Escutcheon4.Door light
5. Inside handle cover
6. Door trim carpet
7.Door trim8.Speaker garnish
9. Power window switch
10.Waterproof film
\handle
NOTE* : Clip locationsTSB Revision

42-42BODY -Door Trim and Waterproof Film / Door Glass and Regulator
ISERVICE POINT OF REMOVAL
1. REMOVAL OF CLIP
IUse a shop towel to remove the clip; and remove door
window regulator handle.
\L.J II
DOOR GLASS AND REGULATORREMOVAL AND INSTALLATION
~;:;zL4., 1l Door Window Glass Adjustment
18FOlQi2
Removal steps
Door trim (Refer to P.42-41
.IWaterproof film (Refer to P.42-41 .I
1. Delta cover inner
2. Delta cover outer
Door belt line outer weatherstrip
(Refer to
P.42-65.)3. up stop
4. Stabilizer inner front
5. Stabilizer inner rear
6. Delta sash
7. Door window glass
8. Door glass guide track front
9. Door window regulator assemblyIO. Door glass guide track rear
IM42MCCA
18FO200
d
I
I
I
!
(
I
L&lTSB Revision

L
/
idBODY
- Power Window
REMOVAL AND INSTALLATION42-51
Cll Door Wlndow Glass Adjustment
18FO205
18FO198Door window regulator assembly removal steps
Door trim (Refer to
P.4241.)Waterproof film (Refer to P.42-41.)1. Delta cover inner
2. Delta cover outer
18FO1996. Delta sash
7. Door window glass
8. Door window regulator assembly
9. Door glass guide track front
10. Door glass guide track rear
Door belt line outer weatherstrip (Refer to
P.42-65.)3. up stop
4. Stabilizer inner frontPower window switch assembly removal steps
Door trim (Refer to P.42-41.)11. Power window switch assembly
5. Stabilizer inner rear
INSPECTION
POWER WINDOW RELAY
(1) Remove .the knee protector assembly.
(Refer to GROUP 52A
- Instrument Panel.)
ow relay from indoorrelaybox.

42-62BODY - Central Door Locking System
REMOVAL AND INSTALLATION16FO196
Door lock actuator removal
Door trim and waterproof film (Refer toP.42-41.)Do&
latch assembly (Refer to P.42-54.)
1. Door lock actuator
18FO205Door lock switch removal
Door trim (Refer to P.42-41.)
2. Door lock switch18FOO52

view A16FOO51INSPECTION
DOOR LOCK ACTUATOR
(1) Place the rod in the LOCK position, apply the battery power
to the terminal
L(3) for driver’s side or (1) for passenger’s
side1 and check to see that when the terminal [(l) for
driver’s side or (3) for passenger’s side] is grounded, the rod
moves to the UNLOCK position.
(2) Then place the rod in the UNLOCK position, apply the
battery power to the terminal [(I) for driver’s side or (3) for
passenger’s side], and check to see that when the terminal
[(3) for driver’s side or (1) for passenger’s side] is grounded,
the rod moves to the LOCK position.
(3) Check to ensure that when the rod is placed in the UNLOCK
position, there is acontinuity between the terminals (2) and
(4). and that when the rod is placed in the LOCK position,
there is no continuity.
TSB Revision

EXTERIOR - Rear Wber and Washer51-35
REAR WIPER AND WASHERM51 KKAO
,/REMOVAL AND INSTALLATION
16FO104.lO
.llRemoval steps of wiper motor
1. Wiper blade
l *2. Wiper arm
3. SpacerRemoval steps of washer tube
Front pillar trim
(RH)Quarter trim (RH)
Liftgate lower trim (Refer to GROUP 52A -Quarter upper trim
(RH)Rear roof rail trim!R$$f$$ GRoUP 52A
Trims.)Rear side trim
(RH)i .
4. Wiper motor
l *8. Liftgate moulding, upper
9. Washer nozzle
Removal steps of washer tank
Rear end trim (Refer to GROUP
52A-Trims.)5. Cap
6. Washer tank
7. Washer motor
10. Tube and grommet assembly
11. Washer tube
1 TSB Revision

INTERIOR - Trims52A-13EMOVAL AND INSTALLATION
19FOO33
Scuff plate
D-D1Quart&
upper trim19FOO2C
1B-B
Front piiar trimc-cIQuart&
upper trim
,wca*
Rear roof rail trim 1 igFoo22Cowl side trim removal steps
1. Scuff plate
2. Cowl side trim
Front pillar trim removal steps
4. Hanger bracket
5. Sash guide cover mounting bolt
6. Clip
7. Front pillar trimRear roof rail trim removal steps
8. Screw
10. Rear roof rail trim
Quarter upper trim removal steps
3. Quarter trim (Refer to
P.52A-14.)48: ;;;;anger9. Quarter upper trim
1 TSB Revision
NOTE(1) @: Location of metallic clip(2) c: Location of resin clip(3)* indicates trim clip. (Refer to P.52A-12.)(4)For door trim,. refer to GROUP 42 - Door TrimandWaterproof Film.
I

L
LINTERIOR
- Headlining52A-17
HEADLININGM52lJDBC[EMOVAL AND INSTALLATION
Pre-removal and Post-installation Operationl Removal and Installation of Rear
Roof Rail Trim (Refer to P52A-13.)l Removal and lnstallatron of FrontPillarTrim (Refer to P.52A-13.)Removal steps
1. Hanger bracket
2. Sash guide cover mounting bolt
3. Clip
4. Passenger compartment temperature
sensor (Vehicles with full automatic
air conditioner)
5. Sunvisor assembly
6. Sunvisor holder
7. Room light assembly
8. HeadliningTSB Revision