hood release MITSUBISHI 3000GT 1991 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: 3000GT, Model: MITSUBISHI 3000GT 1991Pages: 1146, PDF Size: 76.68 MB
Page 67 of 1146
ENGINE - Engine AssemblyII-17
ENGINE ASSEMBLY
/REMOVAL AND INSTALLATION
I
Pre-removal Operationl Release of Residual Pressure from HighPressure Fuel Hose(Refer to GROUP 13 -Service AdjustmentProcedures,)l Removal of Cruise Control Pump andLink Assembly(Refer to GROUP 13 - Cruise Control.)l Removal of Hood(RefertoGROUP42A-Hood.)
l
Removal of Air Hose and Air Pipe
Post-installation Operationl Installation of Radiator(Refer to GROUP 14 - Radiator.)l Installation of Cruise Control Pump andLink Assembly(Refer to GROUP 13 -Cruise Control.)l Installation of Transaxle Assembly(Refer to GROUP 22,23 -Transaxle Assembly.)l lnstallatron of Front Exhaust Pipe(Refer to GROUP 15 - Exhaust Pipe and Main Muffler.)l Installation of Air Hose and Air Pipe
MllSA-B
4 ft.lbs.
6
40-45 Nm
29 - 33 fklbs.
Removal steps
1. Connection of accelerator cable11. Drive belt (Alternator and air conditioner)
2. Connection of brake booster vacuum hose(Refer to P.l l-l 1.)
3. Connection of booster vacuum12. Drive belt (Power steering)
hose
(Referto P.l l-l I.)4. Connection of fuel return hose13. Connection of alternator harness
5. Connection of fuel high pressure hose14. Oxygen sensor connector
6. Connection of ground cablel *15. Air conditioner compressor
7. Solenoid valve assembly4w
16. Power steering oil pump
8. Connection of vapor hose17. Oil pressure switch connector (Power steer-9. Connection of heater hoseing)10. EGR temperature sensor connector18. Connection of oil cooler pipes
OlFOO43
TSB Revision1
Page 890 of 1146
42-18ENGINE HOODBODY
- Engine Hood
M42HAAV
REMOVAL AND INSTALLATION5Nm
9Nm’7 ft.lbs.12 Nm\ /8 ft.lbs.
16FO12716FO261
16A0755
1. Hood latch2. Hood lock release handle3. Hood lock release cable4. Hood weatherstrip (Front)
5. Hood weatherstrip (Rear)
l a6. Bumper A (Body side)I)*7. Bumper A (Hood side)l * 8. BumperB
9. Bumper
10. Hood side weatherstrip (LH)11. Hood side weatherstrip (RH)12. Heat protector panel
13. Heat protector
14. Hood garnish assembly
15. Hood switch (Vehicles with theft-alarm
sys-tern)16. Engine room inspection light
17. Inspection light switchHood hinge removal steps
Washer tube (Refer to GROUP 51 -Wind-shield Wiper and Washer.)
18. inspection light wiring harness19. Hood gas spring20. Hood21. Hood hinge
Caution1.Never try to disassemble the hood gas spring or burn
it.
2.Always bore a hole in the gas spring to release the
interior gas before the spring is discarded.TSB Revision
Page 987 of 1146
INTERIOR - Instrument Panel52A-9
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operationl Removal and Installation of Floor Console
(Refer to P.52A-11.)
19FO131Removal steps
1. Hood lock release handle
2. Rheostat
3. Switch garnish B
4. Knee protector assembly
5. Column cover
6. Glove box striker
7. Glove box and cross pipe cover
8. Center air outlet assembly
9. Heater control assembly installation screws
10. Meter bezel
i*11. Combination meter
12. Speedometer cable adapter (Mechanical
type speedometer)
13. Speaker or plug
14. Harness connector
15. Steering shaft mounting bolts
16. Instrument panel assembly
Front ofSERVICE POINTS OF REMOVAL
5. REMOVAL OF COLUMN COVER
Remove the screws and remove the column cover while
using care not to break the claws.TSB Revision