diagram MITSUBISHI 380 2005 Workshop Manual

FRONT SEAT ASSEMBLY
INTERIOR52A-29
OPERATION CHECK OF POWER SEAT MOTOR
CIRCUIT DIAGRAMS:
Refer to circuit diagrams GROUP-90
Refer to configuration diagrams GROUP-80
NOTE: Check connectors and terminals for damage or
loose connections at the seat harness and all supply
circuits connections to seat. Repair or replace wiring
harness if damaged.
MOTOR DESCRIPTION TERMINAL MEASUREMENT
TRACK/ SLIDE MOTOR BACKWARD 1 MOTOR ON= 12V
MOTOR OFF = GROUND.
FORWARD 2 MOTOR ON= 12V
MOTOR OFF = GROUND.
FRONT LIFT MOTOR UP 1- non memory
5- memoryMOTOR ON= 12V
MOTOR OFF = GROUND.
DOWN 5- non memory
1- memoryMOTOR ON= 12V
MOTOR OFF = GROUND.
REAR LIFT MOTOR UP 1 MOTOR ON= 12V
MOTOR OFF = GROUND.
DOWN 5 MOTOR ON= 12V
MOTOR OFF = GROUND.
RECLINER MOTOR FORWARD 1 MOTOR ON= 12V
MOTOR OFF = GROUND.
BACKWARD 5 MOTOR ON= 12V
MOTOR OFF = GROUND.
LUMBAR MOTOR SOFTER 1 MOTOR ON= 2.5V - 5V
MOTOR OFF = GROUND.
HARDER 2 MOTOR ON= 2.5V - 5V
MOTOR OFF = GROUND.

FRONT SEAT ASSEMBLY
INTERIOR52A-30
1.If abnormality was found, check the power seat
adjuster assembly.
CIRCUIT DIAGRAMS:
Refer to circuit diagrams GROUP-90
Refer to configuration diagrams GROUP-80
NOTE: Check connectors and terminals for damage or
loose connections at the seat harness and all supply
circuits connections to seat. Repair or replace wiring
harness if damaged.

FRONT SEAT ASSEMBLY
INTERIOR52A-32
CIRCUIT DIAGRAMS:
Refer to circuit diagrams GROUP-90
Refer to configuration diagrams GROUP-80
NOTE: Check connectors and terminals for damage or
loose connections at the seat harness and all supply
circuits connections to seat. Repair or replace wiring
harness if damaged.
ERASING DIAGNOSTIC TROUBLE CODES (DTC’s)
The Memory Seat Controller will temporarily store DTC’s when
incorrect operating conditions are detected. The DTC’s are
self-clearing as soon as each fault condition is rectified and
returns to normal operating function. LED FLASH
SEQUENCEFAULT CONDITION
DETECTEDPOSSIBLE CAUSE
2 then 1 No fore lift motor sensor Connection at motor sensor
or open/ short circuit in
wiring harness.
2 then 2 No aft lift motor sensor Connection at motor sensor
or open/ short circuit in
wiring harness.
2 then 3 No track motor sensor Connection at motor sensor
or open/ short circuit in
wiring harness.
2 then 4 No pedal motor sensor Connection at motor sensor
or open/ short circuit in
wiring harness.
2 then 5 No recliner motor sensor Connection at motor sensor
or open/ short circuit in
wiring harness.
2 then 6 No lumbar motor sensor Connection at motor sensor
or open/ short circuit in
wiring harness.
3 then 1 Button stuck MEMORY Button switch cap stuck on
side cover
3 then 2 Manual Button stuck position Button switch cap stuck on
side cover
6 then 3 Power relay welded shut Grime on contact

80-1
GROUP 80
CONFIGURATION
DIAGRAMS
CONTENTS
OVERALL CONFIGURATION
DIAGRAM. . . . . . . . . . . . . . . . . . . . . .80-2
HOW TO READ CONFIGURATION
DIAGRAMS . . . . . . . . . . . . . . . . . . . .80-3
ENGINE COMPARTMENT. . . . . . . . .80-4ENGINE AND TRANSMISSION . . . . .80-6
DASH PANEL . . . . . . . . . . . . . . . . . . .80-10
FLOOR, SEAT AND ROOF . . . . . . . .80-17
DOOR . . . . . . . . . . . . . . . . . . . . . . . . .80-23
LUGGAGE COMPARTMENT . . . . . . .80-24

OVERALL CONFIGURATION DIAGRAM
CONFIGURATION DIAGRAMS80-2
OVERALL CONFIGURATION DIAGRAMM1801000100558
NOTE: .
1. This illustration shows only major wiring harnesses.
2. *: also equipped at the right side.

HOW TO READ CONFIGURATION DIAGRAMS
CONFIGURATION DIAGRAMS80-3
HOW TO READ CONFIGURATION DIAGRAMSM1801000200555
The wiring harness diagrams clearly show the connector locations and harness configurations on actual vehi-
cles. Some variations are included in one configuration diagram. Accordingly, some diagrams may not be
applicable for individual vehicles.

ENGINE COMPARTMENT
CONFIGURATION DIAGRAMS80-4
ENGINE COMPARTMENTM1801000301403
A-01 (2-B) WHEEL SPEED SENSOR (FRONT:
RH)
A-02 (26-B) ABS-ECU OR ABS/TCL-ECU
A-03 (5-B) WINDSHIELD WIPER MOTOR
A-04 (2-B) WHEEL SPEED SENSOR (FRONT:
LH)
A-05X (4) FOG LAMP RELAY
A-06X (4) HORN RELAY
A-10X (4) FAN CONTROL RELAYA-11X (11) FRONT-ECU
A-12X (11) FRONT-ECU
A-13 (17-GR) FRONT WIRING HARNESS AND
CONTROL WIRING HARNESS
COMBINATION
A-14 (6-GR) GROUNDING CONNECTOR
A-17 (2) SIDE TURN SIGNAL LAMP (LH)
A-18 (2) FRONT TURN SIGNAL LAMP (LH)
A-20 (6) HEADLAMP COMBINATION (LH)

ENGINE COMPARTMENT
CONFIGURATION DIAGRAMS80-5
A-22 (2-B) FOG LAMP (LH)
A-23 (2-Y) FRONT IMPACT SENSOR (LH)
A-24 (3-B) RADIATOR AND CONDENSER FAN
CONTROLLER MODULE
A-25 (2-BR) AMBIENT TEMPERATURE SENSOR
A-26 (2-B) HOOD SECURITY SWITCH
A-27 (2-Y) FRONT IMPACT SENSOR (RH)
A-28 (2-B) FOG LAMP (RH)
A-29 (2) WINDSHIELD WASHER MOTORA-30 (3-B) A/C PRESSURE SENSOR
A-32 (6) HEADLAMP COMBINATION (RH)
A-34 (2) FRONT TURN SIGNAL LAMP (RH)
A-35 (2) SIDE TURN SIGNAL LAMP (RH)
A-36 (1-B) HORN (LOW)
A-37 (1-B) HORN (HIGH)
A-38 (2) CONDENSOR FAN CONNECTION
TO CONTROLLER MODULE

ENGINE AND TRANSMISSION
CONFIGURATION DIAGRAMS80-6
ENGINE AND TRANSMISSIONM1801000401079
B-01 (2-GR) INJECTOR 1
B-02 (3-B) MANIFOLD ABSOLUTE PRESSURE
SENSOR
B-03 (2-GR) INJECTOR 3
B-04 (2-GR) INJECTOR 5
B-05 (2-B) EVAPORATIVE EMISSION PURGE
SOLENOID
B-06 (6-B) THROTTLE BODY ASSEMBLY
B-07 (2-GR) BRAKE FLUID LEVEL SWITCHB-08 (4-GR) RIGHT BANK HEATED OXYGEN
SENSOR (REAR)
B-09 (4-B) RIGHT BANK HEATED OXYGEN
SENSOR (FRONT)
B-10 (5) MASS AIRFLOW SENSOR
B-16X (4) A/T CONTROL RELAY
B-17X (4) MPI RELAY
B-18X (4) A/C COMPRESSOR CLUTCH RELAY

ENGINE AND TRANSMISSION
CONFIGURATION DIAGRAMS80-7
B-19 (34) A/T-ECU
B-20 (60) ENGINE-ECU
B-21 (94) ENGINE-ECU
B-22 (26) A/T-ECU
B-24 (4-GR) LEFT BANK HEATED OXYGEN
SENSOR (REAR)
B-25 (4-B) LEFT BANK HEATED OXYGEN
SENSOR (FRONT)
B-26 (2-GR) INJECTOR 6B-27 (2-GR) INJECTOR 4
B-28 (1-B) A/C COMPRESSOR ASSEMBLY
B-29 (1-B) ENGINE OIL PRESSURE SWITCH
B-30 (2-GR) INJECTOR 2
B-31 (1-B) POWER STEERING PRESSURE
SWITCH
B-32 (10-B) CONTROL WIRING HARNESS AND
INJECTOR WIRING HARNESS
COMBINATION