key MITSUBISHI CARISMA 2000 1.G Owner's Manual

INSTRUMENTS AND CONTROLS
4–20
CAUTION
(4) Do not allow objects to touch the
inside of the rear window glass,
damaged or broken wires may re-
sult.
E08A016a
Front fog lamp switch*EE08A-Va
The front fog lamp can be operated when the
headlamps or tail lamps turn on. Push the
switch to turn on the front fog lamps, and
push the switch again to turn them off.
The indication lamp in the instrument cluster
will illuminate while the front fog lamp is on.
NOTE
(1)The front fog lamps are automatically
turned off when the headlamps and
tail lamps turn off.
To turn on the front fog lamps again,
push the switch again when the head-
lamps or tail lamps turn on.(2)In case of vehicles with Daytime Run-
ning Lamp, the front fog lamps can be
operated even if the lamp switch is set
to the
“” (OFF) position, because the
low beam of the headlamps, tail
lamps, etc. illuminate when the igni-
tion key is at the “ON” position.

INSTRUMENTS AND CONTROLS
4–21
Type 1
E08B026a
Rear fog lamp switchEE08BAIa
The rear fog lamp can be operated when the
headlamps or front fog lamps (if so
equipped) turn on.
Push the switch to turn on the gear fog lamp,
and push the switch again to turn it off.
The indication lamp in the instrument cluster
will illuminate while the rear fog lamp is on.
Type 2
E08B011a
NOTE
(1) The rear fog lamp is automatically
turned off when the headlamps and
front fog lamps (if so equipped) turned
off.
To t u r n on the rear fog lamp again, push
the switch again when the headlamps
or front fog lamps (if so equipped) turn
on.
(2) In case of vehicles with Daytime Run-
ning Lamp, the front fog lamp can be op-
erated even if the lamp switch is set to
the “
” (OFF) position, because the
low beam of the headlamps, tail lamps,
etc. illuminate when the ignition key is at
the “ON” position.
(3) The rear fog lamp is installed only on the
driver’s side.
E15A028a
Rheostat
(meter illumination control)
EE15A-Ma
The rheostat can be adjusted while the lamp
switch is “” or “”.
Turn the dial to adjust the meter illumination
to the desired brightness.
1-To increase brightness
2-To reduce brightness

STARTING AND DRIVING
5–9
(6) The heavier weight and higher rolling
and air resistance will increase fuel con-
sumption.
Additional precautions for vehicles
equipped with an automatic
transmission
The “2” position (INVECS–II 4A/T) or 2nd
gear (INVECS–II Sport Mode 4A/T) is re-
commended on slopes or at low speed. Use
the “L” position (INVECS–II 4A/T) or 1st gear
(INVECS–II Sport Mode 4A/T) in mountain-
ous areas in order to make better use of en-
gine braking and to assist the brake system.
However, be sure that the speed does not
exceed the maximum speed limit for the se-
lected gear.
For maximum speed of the vehicles
equipped with INVECS–II 4A/T, refer to the
description of the “Possible driving speed”
on page 5–24.Vehicles with automatic transmission
I21A070a
Ignition switchEI21AAGe
1-The engine is stopped, and the steer-
ing wheel is locked. The key can only
be inserted and removed only when
the switch is in this position.
2-The engine is stopped, but the radio,
cigarette lighter and other electrical
devices can be operated.
3-The engine is running and all the ve-
hicle’s electrical devices can be oper-
ated.
4-The starter motor operates. After the
engine has started, release the key
and it will automatically return to the
“ON” position.
Vehicles with manual transmission
I21A031a

STARTING AND DRIVING
5–10
Vehicles with automatic
transmission
I21A058a
NOTE
(1) For vehicles with a manual trans-
mission, when removing the key, push
the key in at the “ACC” position and
keep it depressed until it is turned to the
“LOCK” position, and remove.
For vehicles with an automatic trans-
mission, when removing the key, first set
the selector lever to the “P” (PARK) posi-
tion, and then turn the key to “LOCK”
and remove it.
(2) For vehicles equipped with the Daytime
Running Lamp, when the ignition switch
is in the “ON” position, the headlamp low
beams etc. are turned on.
(Refer to “Headlamps” on page 4–12.)(3) Your vehicle is equipped with an elec-
tronic immobilizer, to start the engine,
the ID code which the transponder in-
side the key sends must match the one
registered to the immobilizer computer.
(Refer to page 2–2)
Vehicles with manual
transmission
I21A057a

STARTING AND DRIVING
5–11
CAUTION
(1) Do not remove the ignition key
from the ignition switch while
driving. The steering wheel will
lock, causing loss of control.
(2) If the engine is stopped while
driving, the brake servomechan-
ism will cease to function and
braking efficiency will deterio-
rate. Also, the power steering
system will not function and it will
require greater manual effort to
operate the steering.
(3) Do not leave the key in the “ON”
position for a long time when the
engine is not running, doing so
will cause the battery to be dis-
charged.
(4) Do not turn the key to the
“START” position when the en-
gine is running, doing so could
damage the starter motor.
I01B015a
How to lock and unlock the steer-
ing wheel
EI01B-Kb
To lockRemove the key at the “LOCK” position.
Turn the steering wheel until it is locked.
To unlockTurn the key to the “ACC” position while
moving the steering wheel slightly.
CAUTION
Remove the key when leaving the ve-
hicle.
NOTEIf the front wheels are turned, the anti-theft
lock may sometimes make it difficult to turn
the key from “LOCK” to “ACC”. Firmly turn
the steering wheel to the left or to the right as
you turn the key.

STARTING AND DRIVING
5–12
StartingEI02FAIh
Tips for starting
(1) Do not operate the starter motor con-
tinuously for anything longer than 10
seconds; doing so could run down the
battery. If the engine does not start, turn
the ignition switch back to “LOCK”, wait
a few seconds, and then try again.
Trying repeatedly with the starter mo-
tor still turning will damage the starter
mechanism.
(2) If the engine cannot be started because
the battery is weak or dead, refer to the
“Emergency starting” section for instruc-
tions on starting the engine.
(3) The engine is well warmed up if the
coolant temperature gauge needle
starts to move (the engine speed de-
creases). Extended warming - up oper-
ation will result in excessive fuel con-
sumption.
WARNING
Never run the engine in a closed or
poorly ventilated area any longer than
is needed to move your vehicle in or
out of the area. Carbon monoxide
gases are odourless and can be fatal.
CAUTION
(1) Never attempt to start the engine
by pushing or pulling the vehicle.
Especially in the automatic trans-
mission since the structure is dif-
ferent from a manual transmis-
sion, it is not possible to start the
engine by using this technique.
Never attempt this or it could
damage the automatic transmis-
sion.
(2) Do not run the engine at high rpm
or drive the vehicle at high speed
until the engine has a chance to
warm up.
(3) Release the ignition key as soon
as the engine starts to avoid dam-
aging the starter motor.
(4) If your vehicle is equipped with a
turbocharger, do not stop the en-
gine immediately after operating
the vehicle at high speeds. Allow
the engine to idle for approxi-
mately 60 seconds or more to
give the turbocharger a chance to
cool down.
NOTE
After replacing the battery, the electronic
control system data for the engine, auto-
matic transmission, etc., will be erased. As a
result, the engine speed may become un-
stable and shift shocks may occur.
If the engine speed becomes unstable, initial
engine adjustments will need to be per-
formed.
Refer to the section ”What to do if the engine
speed becomes unstable after the battery is
replaced” on page 8–22.
Shift shocks will become smoother after sev-
eral changes in speed.

STARTING AND DRIVING
5–13
I27A036a
Starting the engine
(Petrol-powered vehicles)
This vehicle is equipped with an electroni-
cally controlled fuel injection system which
is automatically controlled. When starting
the engine, do not depress the accelerator
pedal.
Normal conditions
The starting procedure is as follows :
1. Insert the ignition key and fasten the
seat belt.
2. Apply the parking brake.
3. Depress and hold the brake pedal.
4. Place the gearshift lever (manual
transmission) in the “N” (Neutral) or
the selector lever (automatic trans-
mission) in the “P” (PARK) position.
5. Fully depress the clutch pedal (man-
ual transmission).
6. After turning the ignition key to the
“ON” position, make certain that all
warning lamps are functioning proper-
ly before starting the engine.
7. Turn the ignition key to the “START”
position without depressing the accel-
erator pedal, and release it when the
engine starts.
NOTE
A ticking noise may be heard after starting
the engine. This is not an abnormal condi-
tion. The noise will disappear after a short
time of engine running.
If the ticking noise continues after the engine
is warmed up, have your vehicle checked at
an authorized MITSUBISHI dealer.
Flooded engine
If the engine has become flooded during
starting, first operate the starter for 5 to 6 sec-
onds while fully depressing the accelerator
pedal, then start the engine without depres-
sing the accelerator pedal.
At extreme cold ambient
temperature
If the engine won’t start, depress the accel-
erator pedal about halfway while cranking
the engine. Once the engine starts, re-
lease the accelerator pedal.
CAUTION
When starting the engine, make sure
that you press on the brake pedal. At
extreme cold ambient temperature,
move your foot to the brake pedal im-
mediately after the engine has
started.

STARTING AND DRIVING
5–14
I27A075a
Starting the engine
(Diesel-powered vehicles)
1. Insert the ignition key and fasten the
seat belt.
2. Apply the parking brake.
3. Depress and hold the brake pedal.
4. Place the gearshift lever in the “N”
(Neutral) position.
5. Fully depress the clutch pedal.
6. Turn the ignition key to the “ON” posi-
tion. The diesel preheat indication
lamp will first illuminate in amber, and
then after a short time go out, indicat-
ing that preheating is completed.
7. Turn the ignition key to the “START”
position without depressing the accel-
erator pedal, and release it when the
engine starts.NOTE
(1) If the engine is cold, the diesel preheat
indication lamp is on for a longer time.
(2) When the engine has not been started
within about 5 seconds after the diesel
preheat indication lamp will go out, re-
turn the ignition key to the “LOCK” posi-
tion. Then, turn the key to the “ON” posi-
tion to preheat the engine again.
(3) When the engine is warm, the diesel
preheat indication lamp does not come
on, even if the ignition key is placed in
the “ON” position.
Start the engine by turning the ignition
key right to the “START” position.
Type 1
I29A014a
Manual transmissionEI29A–Jd
The shift pattern is shown on the gearshift
lever knob. Be sure to always fully depress
the clutch pedal before attempting to shift the
lever.
For smooth gearchanging

Depress the clutch pedal completely.

1st and 2nd gear: first move the gear
lever fully left and then forward or back
into 1st and 2nd gear.

3rd and 4th gear: move the gear lever
forward or back from neutral (N).

5th gear: first move the gear lever right
and then into 5th gear.

STARTING AND DRIVING
5–25
WaitingEI04G-Ee
For short waiting periods, such as at traffic
lights, the vehicle can be left in gear and held
stationary with the service brake.
For longer waiting periods with the engine
running, the selector lever should be placed
in the “N” (NEUTRAL) position.
CAUTION
(1)Never hold the vehicle stationary
while in gear on a hill with the accel-
erator, always apply the parking
brake and/or service brake.
(2)Unexpected acceleration may occur
if the selector lever is in a position
other than “P” (PARK) or “N” (NEU-
TRAL).
Prior to moving off after having
stopped the vehicle, make sure that
the selector lever is in “D” (DRIVE)
or “Sports mode” position.
ParkingEI04H-Be
To park the vehicle, first bring it to a complete
stop, fully engage the parking brake and
then move the selector lever to the “P”
(PARK) position.
If you are going to leave the vehicle unat-
tended, always switch off the engine and re-
move the ignition key.
NOTE
On a slope, be sure to apply the parking
brake before moving the selector lever to the
“P” (PARK) position. If you move the selector
lever to the “P” (PARK) position without first
applying the parking brake, a stronger than
normal resistance force may be encoun-
tered. In this situation, move the selector
lever strongly when you next wish to drive.
I27A052a
Parking brakeEI07A-Jn
To park the vehicle, first bring it to a complete
stop, fully engage the parking brake and
then move the gear shift lever to 1st (on an
uphill) or Reverse (on a downhill) position, for
vehicles with a manual transmission or set
the selector lever to “P” (PARK) position on
automatic transmission vehicles.
To apply
1-Pull the lever up without pushing the
button at the end of the hand grip.

STARTING AND DRIVING
5–26
I07A045a
To release
1-Pull the lever up slightly.
2-Push the button at the end of the hand
grip.
3-Push the lever downward.
NOTETo prevent the parking brake from being re-
leased unintentionally, the lever must be
pulled upward slightly before it can be
pushed downward. Simply pressing the but-
ton does not enable the lever to be pushed
downward.
When parking on a hill, apply the parking
brake and turn the front wheels towards the
kerb on a downhill grade, away from the kerb
on an uphill grade.
CAUTION
Before driving, be sure that the park-
ing brake is fully released and the
brake warning lamp is off.
If a vehicle is driven without releasing
the parking brake, the brake will be
overheated, resulting in ineffective
braking and possible brake failure.
ParkingEI22A-Al
Parking on a slope
Fully engage the parking brake, and then
move the gearshift lever to 1st (on an uphill)
or reverse (on a downhill) position on manual
transmission vehicle. On automatic trans-
mission vehicle, move the selector lever to
“P” position. When parking on a hill, apply
chocks to wheels for greater safety.
Parking with the engine running
Do not keep the engine running in a closed
or poorly ventilated place. Carbon monoxide
gas is odorless and extremely poisonous
and dangerous.
Where you park
Do not park in a place where there are in-
flammable objects such as dry grass,
leaves, etc... because the exhaust system
with catalyst produces very high tempera-
tures. This may cause a fire.
When leaving the vehicle
Always remove the key from the ignition
switch and lock all doors when leaving the
vehicle unattended.
Always try to park your vehicle in a well lit
area.