key MITSUBISHI CARISMA 2000 1.G User Guide

LOCKING AND UNLOCKING
2–11
F15A299a
NOTE
Gas springs (B) are installed in the locations
illustrated in order to support the tailgate.
Please observe the following in order to pre-
vent damage or faulty operation.

Do not attach any plastic material, tape,
etc., to the gas springs.

Do not tie string, etc., around the gas
springs.

Do not pull on the gas springs when
closing the tailgate or hang items from
the gas springs.
F15A298a
Operation from inside the vehicle
The boot lid (or tailgate) can be locked or un-
locked by using the central door lock switch,
regardless of the position of the ignition key.
1-Unlock
2-Lock
If the boot lid (or tailgate) is locked or un-
locked by using the central door lock switch,
it can still be locked or unlocked with the key.
NOTE
Repeated continous operating between lock
and unlock could cause the central door
locks’ built–in protection circuit to prevent the
system from operating. If this occurs, wait
about one minute before operating the
switch.
F17B006a
Manual window control*EF17B-Ac
1-To open
2-To close

LOCKING AND UNLOCKING
2–12
LHD, Type 1
F17A152a
Electric window control*EF17A–Uf
The electric windows can only be operated
with the ignition switch in the “ON” position.
Each door window opens or closes while the
corresponding switch is pressed.
1-Driver’s door window
2-Front passenger’s door window
3-Rear left door window
4-Rear right door window
5-Lock switch
RHD, Type 1
F17A153a
WARNING
(1) Before operating the electric win-
dow control, make sure that noth-
ing is capable of being trapped
(head, hand, finger, etc.).
(2) Never leave the vehicle without
removing the key.
(3) Never leave a child (or other per-
sons who might not be capable of
safe operation of the electric win-
dow control) in the vehicle alone.
LHD, Type 2
F17A154a
NOTE
Once the battery cable is disconnected, or
the fuse is replaced, it may happen that the
door glasses cannot be operated normally
even after reconnecting the battery cable. In
such a case, take the following steps with all
the door windows.
Pull the power window switch repeatedly to
close the door window completely if it is
open. After it is completely closed, pull the
switch again for one second, and the door
window will resume its normal operation.

LOCKING AND UNLOCKING
2–15
To tilt upWhen the switch (3) is pressed, the rear
sunroof raises approximately 35 mm for
ventilation.
NOTE
Before tilting the sunroof, completely
open the sunshade. Otherwise you will
not have good ventilation.
To closePress the switch (4).
Safety mechanismIf a hand or head is trapped in the closing
sunroof, it will re-open automatically.
Nonetheless, make sure that nobody puts
their head or hand out of the sunroof when
opening or closing.
The opened sunroof will become operational
after a few seconds.
CAUTION
The safety mechanism is cancelled
just before the sunroof is fully closed.
This allows the sunroof to close com-
pletely. Therefore be especially care-
ful that no fingers are trapped in the
sunroof.
F19A013a
SunshadeSlide the sunshade (5) manually to
open and close it.
NOTE
The sunshade will operate together with
the sunroof only when the sunroof is
opened.
CAUTION
Do not attempt to close the sunshade
when the sunroof is opened.
WARNING
(1) Do not put head, hands or anything
else out of the sunroof opening
while driving the vehicle.
(2) Never leave a child (or other per-
son who might not be capable of
safe operation of the sunroof
switch) in the vehicle alone.
(3) Before operating the sunroof,
make sure that nothing is capable
of being trapped (head, hand,
finger, etc.).
NOTE
(1) When leaving the vehicle unattended,
make sure you close the sunroof and
remove the ignition key.
(2) Do not try to operate the sunroof if it is
frozen closed (after snow fall or during
extreme cold).
(3) Do not sit or place heavy luggage on the
sunroof or roof opening edge.
Do not apply any force that may cause
damage to the sunroof.
(4) Release the switch as soon as the sun-
roof reaches the fully open or fully clo-
sed position.
(5) If the sunroof would not operate when
the sunroof switch is operated, release
the switch and check whether some-
thing is trapped by the sunroof. If no-
thing is trapped, have the sunroof chec-
ked at an authorized MITSUBISHI
dealer.

SEATS AND SEATBELTS
3–7
G02C066a
Anti-theft lockEG02D–Aa
The anti-theft lock is located on the top of the
rear seatback. The cylinder is operated with
the master key (A).
When the lock is in the “LOCK” position, the
seatback cannot be folded down by using
the seatback release button.
This feature is useful to help prevent theft
when the vehicle is parked in an exposed
area, because the “trunk through” feature
does not then apply.
The seatback can be folded down when the
lock is turned to the “FREE” position.
1-Lock
2-Free
At other times, leave the lock at the “FREE”
position.
Head restraintsEG26AAP
WARNING
(1) The head restraints can only pro-
tect you if they are correctly ad-
justed.
(2) A cushion or similar device
should not be placed on the seat-
back as it may increase the dis-
tance between your head and the
head restraint and reduce the ef-
fectiveness of the restraint.
G26A075a
Height adjustment
Adjust the head restraint height so that the
centre of the restraint is as close as possible
to eye level to reduce the chances of injury
in the event of collision. Any person too tall
for the restraint to reach their seated eye
level, should adjust the restraint as high as
possible.
To raise the head restraint, move it upward.
To l o w e r the restraint, move it downward
while pushing the height adjusting knob (A)
in the direction of the arrow. After adjustment,
push the head restraint downward and make
sure that it is locked.

SEATS AND SEATBELTS
3–18
Suitability for various seating positionsEG20CMDa
Seating position
Mass GroupFront PassengerRear PassengerFront PassengerRear OutboardRear Centre
0–Up to 10 kg (0 – 9 months)XU,L*1X
0+ – Up to 13 kg (0 – 2 years)XUX
I – 9 to 18 kg (9 months – 4 years)L*2U,L*2L*2
II & III – 15 to 36 kg (4 – 12 years)L*3U,L*3L*3
Key of letters inserted in the above table:U – Suitable for “universal” category restraints approved for use in this mass group.
UF – Suitable for forward–facing “universal” category restraints approved for use in this mass group.
L – Suitable for particular child restraints (MITSUBISHI genuine parts).
B – Built–in restraint approved for this mass group.
X – Seat position not suitable for children in this mass group.
L (Genuine part information)
Genuine parts No.ECE No.
*1MZ311097E1–03301063
*2MZ312389E1–03301085
*3MZ311099E1–03301061
NOTE
There is no applicable MITSUBISHI Genuine Parts to the Mass Group “0+–Up to 13 kg (0–2 years)”.
MITSUBISHI MOTOR SALES Europe B.V. reserves the right to changes without any prior announcement.
For detail information, please consult your authorized MITSUBISHI dealer.

SEATS AND SEATBELTS
3–36
WARNING
(7) Never install a rear-facing child
restraint in the front passenger
seat. A forward-facing child re-
straint should be used in the rear
seat only, whenever possible. If a
forward-facing child restraint
must be used in the front passen-
ger seat, adjust the seat to the
fully backward position and take
care to ensure that the child stays
in the child restraint and away
from the door.
Do not allow the child to lean
against or close to the front door
even if the child is seated in a
child restraint system.
The child’s head should also not
be leaned against or be close to
the area of the seat where the side
air bag is located. It is dangerous
if the side air bag inflates.
Failure to follow all of these in-
structions could lead to serious
or fatal injury to the child.
WARNING
(8) Work around and on the side air
bag system components should
only be done by an authorized
MITSUBISHI dealer. Improper
work could result in inadvertent
deployment of a side air bag or
could render a side air bag inop-
erative; either situation could re-
sult in serious injury.
G28G153a
SRS warning lampEG29F-Ac
There is a supplemental restraint system
(“SRS”) warning lamp on the instrument
panel. The system checks itself and the
lamp tells you if there is a problem. When the
ignition key is turned to the “ON” or “START”
position, the warning lamp should illuminate
for several seconds and then should go out.
This means the system is ready.
The SRS warning lamp is shared by the fol-
lowing:

Driver’s front air bag

Front passenger’s front air bag

Side air bags

Seat belt pre-tensioners

INSTRUMENTS AND CONTROLS
4–9
Charge warning lamp - redED54A–Ra
This lamp illuminates when the ignition key is turned
“ON”, and goes off after the engine has started.
CAUTION
If it illuminates while the engine is running,
there is a problem in the charging system. In
this case, immediately park your vehicle in a
safe place and contact your nearest author-
ized MITSUBISHI dealer.

Abnormality in the charging system

Broken alternator belt
Check engine indication lamp - amberED85AAKa
This lamp is a part of an onboard diagnostic system
which monitors the emissions, engine and automatic
transmission control systems.
If a problem is detected in one of these systems, this
lamp illuminates or flashes. Although your vehicle will
usually be drivable and not need towing, have the sys-
tem checked as soon as possible at an authorized
MITSUBISHI dealer.
This lamp will also illuminate for a few seconds when
the ignition key is turned to the “ON” position. If it does
not go off after a few seconds, take the vehicle to an
authorized MITSUBISHI dealer.
CAUTION
(1) Prolonged driving with this lamp on may
cause further damage to the emission
control system. It could also affect fuel
economy and drivability.
(2) If the lamp does not illuminate when the
ignition key is turned to the “ON” posi-
tion, have the system checked at an auth-
orized MITSUBISHI dealer.

INSTRUMENTS AND CONTROLS
4–10
CAUTION
(3) If the lamp illuminates or flashes while the
engine is running, avoid driving at high
speeds and have the system checked at
an authorized MITSUBISHI dealer.
During vehicle operation with the lamp il-
luminated or flashing, the vehicle may not
accelerate when you depress the acceler-
ator pedal.
When the vehicle is stationary with the
lamp illuminated or flashing, you must de-
press the brake pedal more firmly than
usual since the engine idling speed is
higher than usual and the vehicle with an
automatic transmission has a stronger
tendency to creep forward.
NOTE
The engine electronic control module accommodat-
ing the onboard diagnostic system has various fault
data (especially about the exhaust emission) stored.
This data will be erased if a battery cable is discon-
nected, which will make rapid diagnosis difficult. Do
not disconnect a battery cable when the check engine
indication lamp is ON.
Oil pressure warning lamp - redED25A-Ai
This lamp illuminates when the ignition key is turned
“ON”, and goes off after the engine has started. If it il-
luminates while the engine is running, the oil pressure
is too low.
If the warning lamp illuminates while the engine is run-
ning, turn the engine off and contact your nearest
authorized MITSUBISHI dealer for inspection.
CAUTION
(1) If this lamp illuminates when the engine
oil level is not low, contact your nearest
authorized MITSUBISHI dealer for inspec-
tion.
(2) This warning lamp does not indicate the
amount of oil in the crankcase. This must
be determined by checking the oil level on
the dipstick, while the engine is switched
off.
(3) If you continue driving with low engine oil
level or with this warning lamp illumi-
nated, engine seizure may occur.
NOTE
The oil pressure warning lamp should not be treated
as an indication of the engine’s oil level. The oil level
must be checked using the dipstick.

INSTRUMENTS AND CONTROLS
4–12
E11A015a
Combination headlamps,
dipper and turn signal
switch
EE11AABi
Headlamps
Rotate the switch to turn on the lamps.
–All lamps off
–Position, tail, licence–plate, and
instrument panel lamps on
–Headlamps on and other lamps
remain on
Lamp monitor systemIf the driver’s door is opened when the key is
in the “LOCK” or “ACC” position or removed
from the ignition switch with the lamp switch
in the “
” or “” position, a buzzer will
sound to remind the driver to turn off the
lamps.
Turn off the lamp switch, and the buzzer will
stop.
[Vehicles with Daytime Running Lamp]When the ignition key is in the “ON” position
and the lamp switch is set to the “
” posi-
tion, the low beam of the headlamps, tail
lamps, etc., will illuminate.
NOTE
(1) Do not leave the headlamps and other
lamps on for too long time while the en-
gine is stationary. A run–down battery
could result.
(2) When it rains, or when the vehicle has
been washed, the inside of the lens
sometimes becomes foggy. This is the
same phenomenon as when window
glass mists up on a humid day, and
does not indicate a functional problem.
When the lamp is switched on, the heat
will remove the fog. However, if water
gathers inside the lamp, please go to an
authorized MITSUBISHI dealer for a
check.
E11C013a
Dipper (High/Low beam change)EE11B–Dd
When the lamp switch is in the “” posi-
tion, the beam changes from high to low (or
low to high) each time the lever is pulled to
(1). While the high beam is on, the high
beam indication lamp in the instrument
cluster will also illuminate.
Headlamp flasherEE11C-Fc
The high beams flash when the lever is
pulled slightly to (2), and will go off when it is
released.
When the high beam is on, the high beam in-
dication lamp in the instrument cluster will
also illuminate.
NOTE
The high beams can also flash when the
lamp switch is OFF.

INSTRUMENTS AND CONTROLS
4–18
Precautions to observe when using
wipers and washers
EE13C-L
(1) If the moving wipers become blocked by
ice or other deposits on the glass, the
motor may burn out even if the wiper
switch is turned to OFF. If obstruction
occurs, park your vehicle in a safe
place, turn off the ignition and clean the
deposits from the glass so that the
wipers operate smoothly.
(2) Do not use the wipers when the glass is
dry. They may scratch the glass surface
or the blades may prematurely wear
out.
(3) Before using the wipers in cold weather,
check that the wiper blades are not
frozen onto the glass. The motor may
burn out if the wipers are used with the
blades frozen onto the glass.
(4) Avoid using the washer continuously for
more than 20 seconds. Do not operate
the washer when the fluid reservoir is
empty.
Otherwise, pump failure will occur.
(5) Periodically check the level of washer
fluid in the reservoir and refill if required.
During cold weather, add a recom-
mended washer solution that will not
freeze in the washer reservoir. Failure to
do so could result in loss of washer
function and frost damage to the system
components.(6) If the washer is used in cold weather, the
washer fluid sprayed against the glass
may freeze resulting in poor visibility.
Heat the glass with the defroster or de-
mister before using the washer.
E16A049a
Hazard warning flasher switchEE16A-Dd
Use the hazard warning flasher switch when
the vehicle has to be parked on the road for
any emergency.
The hazard warning flashers can always be
operated, regardless of the position of the
ignition key.
Push the switch to turn on the hazard warn-
ing flashers; push the switch again to turn
them off.
When this switch is operated, all turn - signal
lamps flash continuously, as do the turn - sig-
nal indication lamps in the instrument cluster.