low beam MITSUBISHI CARISMA 2000 1.G Owners Manual

INSTRUMENTS AND CONTROLS
4–6
D50A532d
A: Petrol-powered vehicle
B: Diesel-powered vehicle
Indication and warning lampsED50AMFe1-Turn - signal indication lamps/Hazard warning lamps
2-Automatic transmission indication lamp
(vehicles with A/T only, “N” indicator lamp is used also as A/T
warning lamp.)
Page 5–18
3-High - beam indication lamp
4-Low fuel warning lamp
5-Front fog lamp indication lamp*
6-Rear fog lamp indication lamp
7-Door ajar warning lamp
8-ABS warning lamp*
Page 5–28
9-Brake warning lamp
10 -HOLD indication lamp (vehicle with automatic transmission IN-
VECS-II 4A/T only)
Page 5–20
11-Supplemental restraint (SRS) warning lamp
Page 3–36
12 -Oil pressure warning lamp13 -Charge warning lamp
14 -TCL indication lamp*
Page 5–34
15 -Check engine indication lamp
16 -Cruise control indication lamp*
Page 5–35
17 -Diesel preheat indication lamp
(diesel-powered vehicles only)
18 -Overheating warning lamp
(diesel-powered vehicles only)
NOTE
To find information concerning the indication or warning lamps
marked by the symbol “
Page xx”, refer to the specified pages. For
the other indication and warning lamps, refer to the subsequent
pages.

INSTRUMENTS AND CONTROLS
4–7
Turn-signal indication lamps - greenED52A-Bb
These indication lamps blink on and off when a turn-
signal lamp is operating.
NOTE
If the blinking is too fast, the cause may be a faulty
turn-signal connection or a blown lamp bulb.
Hazard warning indication lamps - greenED30A-A
When the hazard warning lamp switch is pressed, all
turn-signal lamps will flash on and off continuously.
High-beam indication lamp - blueED51A-Aa
This indication lamp illuminates when the high beam
is used.
Low fuel indication lamp - amberED63AMEa
The indication lamp comes on when the fuel tank is
getting low. Refuel as soon as possible.
CAUTION
Do not drive with an extremely low fuel level,
running out of fuel could cause damage to the
catalytic converter.
NOTE
(1) On inclines or curves, due to the movement of
fuel in the tank, the low fuel indication lamp may
come on earlier than usual.
(2)When the engine on diesel–powered vehicles
fails to operate owing to running out of fuel, it
may sometimes be difficult to start after refuel-
ing. This is due to air entering the fuel system.
Therefore, air must be bled from the system.
(Refer to the page 8–21.)
Front fog lamp indication lamp* - greenED74B-A
This lamp illuminates while the front fog lamps are on.

INSTRUMENTS AND CONTROLS
4–12
E11A015a
Combination headlamps,
dipper and turn signal
switch
EE11AABi
Headlamps
Rotate the switch to turn on the lamps.
–All lamps off
–Position, tail, licence–plate, and
instrument panel lamps on
–Headlamps on and other lamps
remain on
Lamp monitor systemIf the driver’s door is opened when the key is
in the “LOCK” or “ACC” position or removed
from the ignition switch with the lamp switch
in the “
” or “” position, a buzzer will
sound to remind the driver to turn off the
lamps.
Turn off the lamp switch, and the buzzer will
stop.
[Vehicles with Daytime Running Lamp]When the ignition key is in the “ON” position
and the lamp switch is set to the “
” posi-
tion, the low beam of the headlamps, tail
lamps, etc., will illuminate.
NOTE
(1) Do not leave the headlamps and other
lamps on for too long time while the en-
gine is stationary. A run–down battery
could result.
(2) When it rains, or when the vehicle has
been washed, the inside of the lens
sometimes becomes foggy. This is the
same phenomenon as when window
glass mists up on a humid day, and
does not indicate a functional problem.
When the lamp is switched on, the heat
will remove the fog. However, if water
gathers inside the lamp, please go to an
authorized MITSUBISHI dealer for a
check.
E11C013a
Dipper (High/Low beam change)EE11B–Dd
When the lamp switch is in the “” posi-
tion, the beam changes from high to low (or
low to high) each time the lever is pulled to
(1). While the high beam is on, the high
beam indication lamp in the instrument
cluster will also illuminate.
Headlamp flasherEE11C-Fc
The high beams flash when the lever is
pulled slightly to (2), and will go off when it is
released.
When the high beam is on, the high beam in-
dication lamp in the instrument cluster will
also illuminate.
NOTE
The high beams can also flash when the
lamp switch is OFF.

INSTRUMENTS AND CONTROLS
4–13
E11D026a
Turn/lane-change signalsEE11D-N
The turn-signal lamps flash when the switch
is operated (with the ignition switch “ON”). At
the same time, the turn signal indicator
flashes.
1-Turn-signals
When making a normal turn, use posi-
tion (1). The lever will return automati-
cally when cornering is completed.
There are times when the lever will not
return after cornering. This occurs
when the steering wheel is turned only
slightly.
In such cases, return the lever by
hand.
2-Lane-change signals
When changing lanes, use position
(2). It will return to the neutral position
when released.NOTE
If the lamp flashes unusually quickly, the bulb
in a turn–signal lamp may have burned out.
Have the vehicle inspected by an authorized
MITSUBISHI dealer.
E01G011a
Headlamp levelling switchEE01GMF
The angle of the headlamp beam varies
depending upon the load carried by the ve-
hicle.
The headlamp levelling switch can be
used to adjust the headlamp illumination
distance (when the lower beam is illumi-
nated) so that the headlamps’ glare does
not distract the drivers of approaching ve-
hicles. Set the switch (referring to the fol-
lowing table) to the appropriate position
according to the number of people and the
load in the vehicle.

INSTRUMENTS AND CONTROLS
4–20
CAUTION
(4) Do not allow objects to touch the
inside of the rear window glass,
damaged or broken wires may re-
sult.
E08A016a
Front fog lamp switch*EE08A-Va
The front fog lamp can be operated when the
headlamps or tail lamps turn on. Push the
switch to turn on the front fog lamps, and
push the switch again to turn them off.
The indication lamp in the instrument cluster
will illuminate while the front fog lamp is on.
NOTE
(1)The front fog lamps are automatically
turned off when the headlamps and
tail lamps turn off.
To turn on the front fog lamps again,
push the switch again when the head-
lamps or tail lamps turn on.(2)In case of vehicles with Daytime Run-
ning Lamp, the front fog lamps can be
operated even if the lamp switch is set
to the
“” (OFF) position, because the
low beam of the headlamps, tail
lamps, etc. illuminate when the igni-
tion key is at the “ON” position.

INSTRUMENTS AND CONTROLS
4–21
Type 1
E08B026a
Rear fog lamp switchEE08BAIa
The rear fog lamp can be operated when the
headlamps or front fog lamps (if so
equipped) turn on.
Push the switch to turn on the gear fog lamp,
and push the switch again to turn it off.
The indication lamp in the instrument cluster
will illuminate while the rear fog lamp is on.
Type 2
E08B011a
NOTE
(1) The rear fog lamp is automatically
turned off when the headlamps and
front fog lamps (if so equipped) turned
off.
To t u r n on the rear fog lamp again, push
the switch again when the headlamps
or front fog lamps (if so equipped) turn
on.
(2) In case of vehicles with Daytime Run-
ning Lamp, the front fog lamp can be op-
erated even if the lamp switch is set to
the “
” (OFF) position, because the
low beam of the headlamps, tail lamps,
etc. illuminate when the ignition key is at
the “ON” position.
(3) The rear fog lamp is installed only on the
driver’s side.
E15A028a
Rheostat
(meter illumination control)
EE15A-Ma
The rheostat can be adjusted while the lamp
switch is “” or “”.
Turn the dial to adjust the meter illumination
to the desired brightness.
1-To increase brightness
2-To reduce brightness

STARTING AND DRIVING
5–10
Vehicles with automatic
transmission
I21A058a
NOTE
(1) For vehicles with a manual trans-
mission, when removing the key, push
the key in at the “ACC” position and
keep it depressed until it is turned to the
“LOCK” position, and remove.
For vehicles with an automatic trans-
mission, when removing the key, first set
the selector lever to the “P” (PARK) posi-
tion, and then turn the key to “LOCK”
and remove it.
(2) For vehicles equipped with the Daytime
Running Lamp, when the ignition switch
is in the “ON” position, the headlamp low
beams etc. are turned on.
(Refer to “Headlamps” on page 4–12.)(3) Your vehicle is equipped with an elec-
tronic immobilizer, to start the engine,
the ID code which the transponder in-
side the key sends must match the one
registered to the immobilizer computer.
(Refer to page 2–2)
Vehicles with manual
transmission
I21A057a

FOR EMERGENCIES
8–26
N29C001a
5. Insert a new fuse of the same capacity
into the clip and insert the fuse at the
same place in the fuse box.
CAUTION
(1) If the newly inserted fuse blows
again after a short time, have the
electrical system checked and re-
paired by an authorized MITSUBI-
SHI dealer to find the cause and
rectify it.
(2) Never use a fuse with a capacity
larger than that specified or any
substitute, such as wire, foil, etc.;
doing so will cause the circuit wir-
ing to heat up and could cause
fire.
Replacement of lamp bulbsEN10A-Ab
Before replacing a bulb, ensure the lamp is
off. Do not touch the glass part of the new
bulb with your bare fingers; the skin oil left on
the glass will evaporate when the bulb gets
hot and the vapor will condense on the re-
flector and dim the surface.
N10B296a
Bulb capacityEN10BMDh
A bulb should only be replaced with a new
bulb of the same rating and type. The desig-
nation can be found on the base of the bulb.
Outside
1-Position lamps 4W (T4W). . . . . . . . .
2-Headlamps, High/low beam
60/55W (H4) . . . . . . . . . . . . . . . . . . . .
3-Front turn - signal lamps
21W (PY21W) . . . . . . . . . . . . . . . . . .
4-Side turn - signal lamps
5W (WY5W) . . . . . . . . . . . . . . . . . . . .
5-Front fog lamps* 55W (H3). . . . . . . .