time MITSUBISHI ECLIPSE 2011 4.G User Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2011, Model line: ECLIPSE, Model: MITSUBISHI ECLIPSE 2011 4.GPages: 494, PDF Size: 15.44 MB
Page 105 of 494
3-10 Features and controls
3
NOTEThe indicator light (5) comes on each time a switch is
pressed.
The keyless entry system does not work if the key is in the
ignition.
The remote control transmitter can be used from about 40
feet (12 m) away. However, this distance may change if
your vehicle is near a TV transmitting tower, a power sta-
tion, or a radio station.
If the UNLOCK button (2) is pressed and no door or rear
hatch or trunk lid is opened within approximately 30 sec-
onds: relocking will automatically occur.
If the following conditions are observed after pressing the
LOCK (1) or UNLOCK (2) button on the remote control
transmitter, the battery in the remote control transmitter
may need to be replaced.
• The doors and the rear hatch or trunk lid cannot be
locked or unlocked.
• The panic alarm cannot be operated.
• The indicator light (5) is dim or does not come on.
If you lose your remote control transmitter, please contact
an authorized Mitsubishi Motors dealer for a replacement.
If you wish to obtain an additional remote control trans-
mitter, please contact an authorized Mitsubishi Motors
dealer. A maximum of 4 remote control transmitters can
be programmed for your vehicle.
NOTEYour keyless entry system operates on a radio frequency
subject to Federal Communications Commission (FCC)
Rules (For vehicles sold in U.S.A.) and Industry Canada
Rules (For vehicles sold in Canada). This device complies
with Part 15 of the FCC Rules and RSS-210 of the Indus-
try Canada Rules. Operation is subject to the following
two conditions.
• This device may not cause harmful interference.
• This device must accept any interference received,
including interference that may cause undesired opera-
tion.
CAUTION
!Changes or modifications not expressly approved by
the manufacturer for compliance could void the
user’s authority to operate the equipment.
BK0115900US.book 10 ページ ２００９年１０月２７日 火曜日 午後１２時１分
Page 116 of 494
Features and controls
3-21
3
You and your family should familiarize yourselves with the
location and operation of the emergency trunk lid release han-
dle. Children should be taught not to play in or around vehi-
cles.To open the trunk from the inside, pull the handle in the direc-
tion of the arrow on the handle. Push up on the trunk lid to
open the trunk and climb out.
WA R N I N G
!Children should never be left unsupervised in or
around vehicles.Unsupervised children could lock themselves in an
open vehicle or trunk.People trapped inside a vehicle or trunk, even if only
for a short period of time, can quickly die from suf-
focation or heat stroke, especially on hot days. Inte-
rior temperatures in vehicles can rise in minutes.Keep your vehicle doors locked and the trunk lid
closed when not in use. Keep your vehicle keys away
from children.
CAUTION
!When loading the trunk, place your things so that
they will not touch the emergency trunk lid release
handle when you close the trunk. Otherwise you
could damage the handle and make it unusable.Always keep the handle in its holder when driving so
that your cargo cannot accidentally bump it and
open the trunk.
Handle
Holder
BK0115900US.book 21 ページ ２００９年１０月２７日 火曜日 午後１２時１分
Page 121 of 494
3-26 Features and controls
3Power windows
N00510800338
In an ECLIPSE SPYDER, operating a power window switch
causes the door window and quarter window to move together.
However, within about 4 inches from the fully closed position,
only the door window moves without accompanying the quar-
ter window.
NOTEDepending on the position of the door window, the door
window may briefly stop then continue moving before
reaching the fully closed position.
Never try to operate the main switch and sub switch in dif-
ferent directions at the same time. This will freeze the
window in position.
Operating the power windows repeatedly with the engine
stopped will run down the battery. Use the window
switches only while the engine is running. NOTEIf a power window stops moving during operation due to a
drop in the battery voltage, it may not automatically return
to normal operability when the battery has been charged.
In this event, take the following corrective action:
With the door closed, pull up the power window switch to
fully close the window. After releasing the switch, pull it
up again for approximately 1 second. Normal opening and
closing of the window will then be possible.
1- Open (down)
2- Close (up)
WA R N I N G
!Before operating the power windows, make sure
that nothing can be trapped (head, hands, fingers,
etc.) in the window. Never leave the vehicle without removing the key. Never leave a child alone in the vehicle.
BK0115900US.book 26 ページ ２００９年１０月２７日 火曜日 午後１２時１分
Page 122 of 494
Features and controls
3-27
3
Main switch The main switch located on the driver’s door can be used to
operate all the windows.
The windows will move while the switch is pressed and stop
when the switch is released.
Sub switchA sub switch can be used for its own passenger side window,
unless the driver’s window lock switch is activated. Timer functionThe power windows can be run up or down when the ignition
key is in the “ON” position.
The windows can be opened or closed for a 30 second period
after the ignition key is turned to the “ACC” or “LOCK” posi-
tion. However, once the driver’s door or the passenger’s door is
opened, the power windows cannot be operated.
1- Driver’s door window switch (ECLIPSE)
Driver ’s door window and driver’s side quarter window
switch (ECLIPSE SPYDER)
(To open the window all the way, you do not need to hold the
switch down for the entire time.)
2- Passenger door window switch (ECLIPSE)
Passenger door window switch and passenger’s side quarter
window switch (ECLIPSE SPYDER)
3- Window lock switch
1- Close
2- Open
BK0115900US.book 27 ページ ２００９年１０月２７日 火曜日 午後１２時１分
Page 123 of 494
3-28 Features and controls
3
Lock switch
N00549000101
When this switch is in the lock mode, the main switch for pas-
senger’s side window and the sub switch cannot be used to
open or close the window, and the main switch will open or
close only the driver’s side window. To unlock the switch,
press it again.
Sunroof (ECLIPSE only, if so equipped)
N00511000571
The sunroof can be opened and closed with the ignition key in
the “ON” position. To open Press the switch (1), the sunroof automatically opens and the
sunroof will stop several centimeters this side of the full open
position. Press the switch (1) again, and the sunroof will be
fully open.
To stop the moving sunroof, press the switch. NOTEThe sunroof stops just before reaching the fully open posi-
tion. If the vehicle is driven with the sunroof in this posi-
tion, wind buffeting is lower than with the sunroof fully
open.
1- Lock
2- Unlock
WA R N I N G
!Before driving with a child in the vehicle, be sure to
lock the window switch to make it inoperative. Chil-
dren tampering with the switch could easily trap
their hands or heads in the window.
BK0115900US.book 28 ページ ２００９年１０月２７日 火曜日 午後１２時１分
Page 124 of 494
Features and controls
3-29
3
To closeThe sunroof closes while the switch (3) is pressed.To tilt up When the switch (2) is pressed, the rear edge of sunroof raises
for ventilation. To tilt down Press the switch (3). Timer functionThe sunroof can be operated when the ignition key is in the
“ON” position. The sunroof can be opened or closed for a 30
seconds period after the ignition switch is turned off. However,
once the driver’s door or the passenger’s door is opened, the
sunroof cannot be operated until the ignition switch is turned
on again.
SunshadeThe sunshade can be opened or closed manually while the
sunroof is closed.
When the sunroof is opened, the sunshade will also open auto-
matically.NOTEBe sure to tilt down the sunroof before closing the sun-
shade.
CAUTION
!Do not attempt to close the sunshade when the
sunroof is opened.Be careful that hands are not trapped when closing
the sunshade.
BK0115900US.book 29 ページ ２００９年１０月２７日 火曜日 午後１２時１分
Page 127 of 494
3-32 Features and controls
3
NOTEThe opening or closing operation of the top cannot be per-
formed when the vehicle is in motion.
For information about the cleaning of the top, refer to the
section “Convertible top” on page 7-76.
When leaving the vehicle unattended, be sure to close the
top and remove the ignition key.
To avoid damage, do not sit or place luggage or any heavy
objects on the top itself, or the area around it.
Make sure nothing is in the top storage area (top and
behind the rear seats) when raising or lowering the top.
Even a small article may interfere with the operation of
the top and may damage the top or cause it to malfunction.
Always be sure the top is completely dry before it is low-
ered. Lowering the top while wet or damp may cause inte-
rior water damage, water stains or mildew of the top. It
can also cause the top to deteriorate and shrink.
Never operate the top when temperatures are 32 °F (0 °C)
or below. The fabric of the top may be damaged. If neces-
sary, allow the vehicle to set for a while in a heated garage
prior to operating the convertible top mechanism.
A roof top or luggage carrier of any type or design MUST
NOT be used on the ECLIPSE SPYDER’s top. This
includes, but is not limited to ski, bicycle or luggage
racks. Damage to the top may result.
Before opening or closing the top, make sure there are no
obstructions above the vehicle. For opening and closing of
the top, there must be upward clearance of approximately
6.6 feet (2 m) as measured from the ground.
The trunk lid cannot be opened until opening or closing of
the electric convertible top is complete.The power windows cannot be operated until opening or
closing of the electric convertible top is complete.
Normal operation
N00504900015
The top can be opened and closed using the top switches.Requirements for operation
N00505000026
The top can be opened and closed when the following require-
ments are all satisfied.
The ambient temperature is 32 °F (0 °C) or higher.
The vehicle is stationary.
The ignition switch is in the “ON” position.
The trunk lid is closed.
The latch handles are unlocked.NOTEIf either of the top switches is operated when the require-
ments for operation are not all satisfied, the operation
indicator lamp will flash slowly (approximately one flash
per second) and a tone will sound intermittently and rap-
idly (approximately three times per second) to indicate
that opening/closing operation is not possible.
If you are not able to perform opening/closing operation
when the requirements are all satisfied, have the vehicle
inspected by an authorized Mitsubishi Motors dealer.
BK0115900US.book 32 ページ ２００９年１０月２７日 火曜日 午後１２時１分
Page 128 of 494
Features and controls
3-33
3
To p s w i t c h e s
N00505100030
The top can be opened and closed using the switches. The top
moves only while a switch is being pushed.NOTEIf the OPEN switch and CLOSE switch are both pushed at
the same time, the operation indicator lamp will flash
slowly (approximately one flashes per second) and a tone
will sound intermittently and rapidly (approximately three
per second) to indicate that the top is not going to work.
To operate the top, release the switches and push the rele-
vant switch again.If the switches are continuously pushed one after the
other, a protection circuit may operate, making the electric
convertible top temporarily inoperable. In this event, the
operation indicator lamp will flash slowly (approximately
one flash per second) and a tone will sound intermittently
(approximately three times per second). Wait about 7 min-
utes, then try operating the electric convertible top again.
To open the top
N00505200031
1. Without obstructing traffic, stop the vehicle on a level,
firm surface where the top can be safely operated.
2. Securely apply the parking brake. If the vehicle has an
automatic transaxle, place the selector lever in the “P”
(PARK) position. If the vehicle has a manual transaxle,
place the gearshift lever in the “N” (Neutral) position.NOTEThe top can be operated with the selector lever of an auto-
matic transaxle in a position other than “P” (PARK) and
with the gearshift lever of a manual transaxle in a position
other than “N” (Neutral). For safety, however, you should
place the selector lever or gearshift lever (as relevant) in
the indicated position and apply the parking brake.
3. Start the engine.NOTEOperating the top without the engine running can drain the
battery. To avoid a dead battery, operate the top with the
engine running.
4. Pull down both sun visors.
1- OPEN switch
2- CLOSE switch
3- Operation indicator lamp
12
3
BK0115900US.book 33 ページ ２００９年１０月２７日 火曜日 午後１２時１分
Page 131 of 494
3-36 Features and controls
3
NOTEDuring operation of the top, if the switch is released
before the top has fully closed or retracted, the top will
stop moving and the operation indicator lamp will flash
slowly (approximately one flash per second).
If operation of the top is stopped for more than 4 minutes
before it has fully closed or retracted, the top (depending
on its location) will slowly move toward the closed or
retracted position. During this time, the operation indica-
tor lamp will flash rapidly (approximately two flashes per
second) and the top switch will be inoperable. When the
operation indicator lamp stops flashing (approximately 2
minutes later), the top switch will again become operable.
The operation indicator lamp is illuminated while the top
is moving.
When the OPEN switch is pushed, the door windows and
quarter windows automatically open fully before the top
starts moving.
If the CLOSE switch is pushed when the top is fully
closed, the operation indicator lamp flashes slowly
(approximately one flash per second) and a tone sounds
intermittently and rapidly (approximately three times per
second) to indicate that the top is not going to move.
To close the top
N00505300045
1. When you push the CLOSE switch, a tone will sound and
the top will start to operate. Keep pressing the CLOSE
switch until the top is fully closed. Refer to “Top
switches” on page 3-33.NOTEWhen the top reaches the fully closed position, a tone
sounds once and the operation indicator lamp goes off to
show that the operation is complete.
WA R N I N G
!To avoid injury, keep hands and head away from the
top while it is operating.To prevent uncontrolled movement of the top,
always keep the vehicle engine running when oper-
ating the top.
BK0115900US.book 36 ページ ２００９年１０月２７日 火曜日 午後１２時１分
Page 132 of 494
Features and controls
3-37
3
NOTEDuring operation of the top, if the switch is released
before the top has fully closed or retracted, the top will
stop moving and the operation indicator lamp will flash
slowly (approximately one flash per second).
If operation of the top is stopped for more than 4 minutes
before it has fully closed or retracted, the top (depending
on its location) will slowly move toward the closed or
retracted position. During this time, the operation indica-
tor lamp will flash rapidly (approximately two flashes per
second) and the top switch will be inoperable. When the
operation indicator lamp stops flashing (approximately 2
minutes later), the top switch will again become operable.
The operation indicator lamp is illuminated while the top
is moving.
When the CLOSE switch is pushed, the door windows
and quarter windows automatically open fully before the
top starts moving.
If the OPEN switch is pushed when the top is fully open,
the operation indicator lamp flashes slowly (approxi-
mately one flash per second) and a tone sounds intermit-
tently and rapidly (approximately three times per second)
to indicate that the top is not going to move.
WA R N I N G
!To avoid injury, keep hands and head away from the
top while it is operating.To prevent uncontrolled movement of the top,
always keep the vehicle engine running when oper-
ating the top.
BK0115900US.book 37 ページ ２００９年１０月２７日 火曜日 午後１２時１分