2 ohm MITSUBISHI ENDEAVOR 2004 Service Manual PDF

CENTRAL DOOR LOCK SWITCH CONTINUITY CHEC
K
Fig. 37: Identifying Door Lock Switch (Driver Side)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
< PASSENGER'S SIDE > CENTRAL DOOR LOCK SWITCH CONTINUITY CHECK SWITCH POSITION
TESTER CONNECTION
SPECIFIED
CONDITION
LOCK
5-12
Less than 2 ohms
OFF
5-12, 10-12
Open circuit
UNLOCK
10-12
Less than 2 ohms

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Fig. 38: Identifying Door Lock Switch (Passenger Side)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
WINDOW GLASS RUNCHANNEL AND DOOR OPENING WEATHERSTRIP REMOVAL AND INSTALLATION SWITCH POSITION
TESTER CONNECTION
SPECIFIED
CONDITION
LOCK
1-2
Less than 2 ohms
OFF
1-2, 2-3
Open circuit
UNLOCK
2-3
Less than 2 ohms

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Fig. 17: Checking Resistance

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the resistance less than 2 ohms?
YES: Go to Step 11 .
NO: Go to Step 10.
STEP 10. Check the harness wire between fan control module connector
A-23 (terminal 1) and ground.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Cooling - Endeavor

FAN CONTROL RELAY CONTINUITY CHEC
K
RADIATOR REMOVAL AND INSTALLATION BATTERY VOLTAGE
TERMINAL NO. TO
BE CONNECTED TO
TESTER
CONTINUITY
TEST RESULTS
Not applied
4-2
Open circuit
Connect terminal No.3 and
battery (-) terminal. Connect
terminal No. 1 and battery (+)
terminal.
4-2
Less than 2 ohms

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Cooling - Endeavor

Fig. 10: Locating Soldered Wires

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ROTOR 1. Check the continuity between the slip rings of the field coil. If the resistance
value is not within 2-5ohm, replace the rotor. See Fig. 11
.
2. Check the continuity between the slip ring and the core. If there is continuity,
re
place the rotor. See Fig. 12
.

2004 Mitsubishi Endeavor Limited
2004 STARTING & CHARGING SYSTEMS Generators & Regulators - Endeavor

Fig. 12: Checking Continuity Between Slip Ring & Core

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
RECTIFIER 1. Check the continuity between the positive rectifier and the stator coil lead
connection terminal with a tester. If there is continuity between the terminals,
the diode is shorted, so replace the rectifier. See Fig. 13
.
2. Check the continuity between the negative rectifier and the stator coil lead
connection terminal with a tester. If there is continuity between the terminals,
the diode is grounded, so replace the rectifier. See Fig. 14 .
3. Check the continuity of the 3 diodes by connecting an ohmmeter to both ends
of each diode. If there is continuity between the directions, or if there is no
continuit
y, the diode is dama
ged, so re
place the rectifier. See Fi
g. 15
.

2004 Mitsubishi Endeavor Limited
2004 STARTING & CHARGING SYSTEMS Generators & Regulators - Endeavor

1. Disconnect the clock spring connector C-306.
Fig. 23: Disconnecting Clock Spring Connector C
-306

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Measure resistance between terminal 3 and ground.
The measured value should be 2 ohm or less.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 24: Disconnecting Clock Spring Connector C
-306

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the measured resistance 2 ohms or less?
YES: Go to Step 7 .
NO: Go to Step 5.
STEP 5. Check radio, CD player and CD changer connector C-110 and
clock spring connector C-306 for loose, corroded or dama
ged terminals, or
terminals pushed back in the connector.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 33: Measuring Resistance

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 34: Identifyin gCircuit Specified Condition

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the measured resistance 2 ohms or less?
YES: Go to Step 9.
NO: Replace the clock spring.
STEP 9. Check the clock spring connector C-303 and switch (RH)
connector C-301 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 53: Disconnecting Audio Amplifier Connector C
-11
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Measure the resistance between terminal 7 and ground.
Fig. 54: Measuring Resistance Between Terminal 7 And Ground

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
The resistance should be 2 ohms or less.
3. Measure the resistance between terminal 17 and ground. The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES: Go to Step 7 .
NO: Go to Ste
p 5.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor