thermostat MITSUBISHI LANCER 2005 User Guide

WATER HOSE AND WATER PIPE
ENGINE COOLING14-34
REMOVAL SERVICE POINT
<> RADIATOR UPPER HOSE
DISCONNECTION
After making mating marks on the radiator upper
hose and hose clamp, disconnect the radiator upper
hose.
INSTALLATION SERVICE POINTS
>>A<< COOLING WATER LINE O-RING
INSTALLATION
CAUTION
Do not allow engine oil or other grease to adhere
to the cooling water line O-ring
Insert the cooling water line O-ring to the water pump
water inlet pipe, and coat the outer portion of the
cooling water line O-ring with water or engine
coolant.
>>B<< THERMOSTAT CASE
ASSEMBLY/COOLING WATER OUTLET
HOSE FITTING INSTALLATION
1. Use a gasket scraper or wire brush to completely
eliminate all gasket material on the gasket
mounting surface.
2. Apply a bead of the specified sealant.
Specified Sealant: MITSUBISHI GENUINE
PART No.MD970389 or equivalent
3. With the sealant still wet (within 15 minutes after
the sealant is applied), install the thermostat case
assembly or cooling water outlet hose fitting. Do
not apply the sealant in an area more than the
required.
>>C<< RADIATOR UPPER HOSE
CONNECTION
1. Insert radiator upper hose as far as the projection
of the cooling water outlet hose fitting.
2. Align the mating marks on the radiator upper hose
and hose clamp, and then connect the radiator
upper hose.
INSPECTIONM1141003400296
WATER PUMP INLET PIPE AND
THROTTLE BODY WATER HOSES
CHECK
Check the water pipe and hoses for cracks, damage
and clogs. Replace them if necessary.
AC200641AC
Mating marks
AC200644AC
O-ring
Water inlet pipe
Water pump or thermostat case
AC200642
Mating marks
Projection
Cooling water outlet
hose fitting
AJ
Radiator upper
hose

RADIATOR
ENGINE COOLING14-37
REMOVAL SERVICE POINT
<> RADIATOR UPPER
HOSE/RADIATOR LOWER HOSE
DISCONNECTION
Make mating marks on the radiator hose and the
hose clamp. Disconnect the radiator hoses.
INSTALLATION SERVICE POINT
>>A<< RADIATOR LOWER
HOSE/RADIATOR UPPER HOSE
CONNECTION
1. Insert radiator lower hose as far as the projection
of the cooling water inlet hose fitting.
2. Insert radiator upper hose as far as the projection
of the thermostat case assembly <4G1> or the
cooling water outlet hose fitting <4G6>.
3. Align the mating marks on the radiator hose and
hose clamp, and then connect the radiator hose.
12. Cooling fan motor & shroud
assembly
13. A/C condenser fan motor & shroud
assembly <4G6>
14. Radiator assembly
Cooling fan motor removal
steps
3. Radiator condenser tank hose
<> >>A<<5. Radiator upper hose
7. Cooling fan motor drive control unit
connector Radiator removal steps
12. Cooling fan motor & shroud
assembly
15. Cooling fan (L.H.)
16. Cooling fan (R.H.) <4G1 (Vehicles
with A/C)>
17. Cooling fan motor drive control unit
18. Cooling fan motor (L.H.)
19. Cooling fan (R.H.) motor <4G1
(Vehicles with A/C)>
20. Cooling fan shroudCooling fan motor removal steps
(Continued)
AC200641AC
Mating marks
AC200642
Mating marks
Projection
Cooling water hose fitting
or thermostat case assembly
AK
Radiator hose

HEATED SEAT
CIRCUIT DIAGRAMS90-143
HEATED SEAT
M1901010700406
BATTERYIGNITION
SWITCH (IG2)
HEATED
SEAT
SWITCHRELAY
BOXRELAY
BOX
RHEOSTAT
HEATED
SEAT
RELAYFRONT-ECU
TAIL LAMP
RELAY
HEATED SEAT
SWITCH
HEATED SEAT
ASSEMBLY (LH)HEATED SEAT
ASSEMBLY (RH)
SEAT
CUSHION
HEATERSEAT
CUSHION
HEATER
SEAT
BACK
HEATER
THERMOSTAT
THERMOSTAT
THERMOSTAT THERMOSTAT
SEAT
BACK
HEATER
HEATER HEATER
TAIL LAMP,
POSITION LAMP,
LICENCE PLATE
LAMP AND LIGHTING
MONITOR BUZZER
NOTE
:
HEATED
SEAT
RELAYHEATED
SEAT
SWITCH
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet