ignition switch MITSUBISHI LANCER 2005 Repair Manual

IGNITION SWITCH
CHASSIS ELECTRICAL54A-27
IGNITION SWITCH
REMOVAL AND INSTALLATIONM1543002100434
WARNING
•Before removal of the air bag module, refer to GROUP 52B, SRS Service Precautions and
Air Bag Module and Clock Spring P.52B-5.
•When removing and installing the steering wheel, do not let it bump against the air bag
module.
AC304659
2
3
4
67
15
AB
8
Removal steps
1. Column cover lower
2. Column cover upper
3. Steering wheel and air bag module
assembly (Refer to GROUP 37,
Steering wheel P.37-17 or P.37-19)
4. Clock spring and column switch
assembly (Refer to GROUP 37,
Steering shaft P.37-21)
<>5. Steering lock cylinder•Ignition switch connector
6. Ignition switch
7. Immobilizer-ECU
•Key reminder switch connector
8. Key reminder switch and bulb
assembly Removal steps (Continued)

IGNITION SWITCH
CHASSIS ELECTRICAL54A-28
REMOVAL SERVICE POINT
<> STEERING LOCK CYLINDER
REMOVAL
1. Insert the key in the steering lock cylinder and turn
it to the "ACC" position.
2. Using a small Phillips head screwdriver, pull the
steering lock cylinder toward you.
INSPECTIONM1544009700203
IGNITION SWITCH CONTINUITY CHECK
Disconnect ignition switch connector C-201 without
removing the ignition switch. Then check the
continuity.
KEY REMINDER SWITCH CONTINUITY
CHECK
Disconnect key reminder switch connector C-202
without removing the ignition switch and key
reminder switch. Then check the continuity.
AC304831AB
Locking pin
AC304833AB
Switch
position Tester
connectionSpecified
condition
"LOCK" (OFF) 1 − 2, 1 − 3,
1 − 4, 1− 5,
1 − 6, 2 − 3,
2 − 4, 2− 5,
2 − 6, 3 − 4,
3 − 5, 3 − 6,
4 − 5, 4 − 6,
5 − 6Open circuit
"ACC" 1 − 6 Less than 2
ohms
"ON" 1 − 2, 1 − 4,
1 − 6, 2 − 4,
2 − 6, 4 − 6Less than 2
ohms
"START" 1 − 2, 1 − 5,
2 − 5Less than 2
ohms
Status of
ignition keyTester
connectionSpecified
condition
Removed 4 − 6 Less than 2
ohms
Inserted 4 − 6 Open circuit
AC304834AB

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-32
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Speedometer does not work (the other meters work).
Speedometer Circuit
IGNITION
SWITCH (IG1)
VEHICLE
SPEED
SENSORDIAGNOSIS
CONNECTORCOMBINATION
METER
ENGINE-ECU
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet CONTROL CIRCUIT
FRONT SIDE
NOTE
LH drive vehicles
RH drive vehicles
,

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-33
TECHNICAL DESCRIPTION (COMMENT)
The engine-ECU and its associated components, the
combination meter assembly, the wiring harness, or
the connector(s) may be defective.
TROUBLESHOOTING HINTS
•Malfunction of the vehicle speed sensor
•Malfunction of the engine-ECU
•Malfunction of the combination meter assembly
•The wiring harness or connectors may have
loose, corroded, or damaged terminals, or
terminals pushed back in the connector.
DIAGNOSIS PROCEDURE
STEP 1. MUT-II/III actuator test.
(1) Connect the MUT-II/III to the diagnosis connector.(2) Use the MUT-II/III to enter simulated vehicle
speed.
Q: Does the speedometer show that simulated vehicle
speed?
YES :
Go to Step 6.
NO : Go to Step 2.
STEP 2. Check the vehicle speed sensor.
(MUT-II/III diagnosis code)
(1) Connect MUT-II/III to the diagnosis connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the MPI system diagnosis code.
Q: Is MPI system diagnosis code P0500 set?
YES :
Refer to P.13A-186 <4G1> or P.13B-166
<4G6>.
NO : Go to Step 3.
AC304777
Steering shaft
AB
MB991502

AC304950
MB991911
16-PIN
MB991827 MB991824
AB

AC304777
Steering shaft
AB
MB991502

AC304950
MB991911
16-PIN
MB991827 MB991824
AB

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-37
INSPECTION PROCEDURE 2: Speedometer does not work (the other meters work).
IGNITION
SWITCH (IG1)
A/T
CONTROL
RELAY
OUTPUT
SHAFT
SPEED
SENSOR
DIAGNOSIS
CONNECOTR
ENGINE-
A/T-ECUCOMBINATION METER
ENGINE-
A/T-ECU
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
FRONT SIDE
NOTE
LH drive vehicles
RH drive vehicles
CONTROL CIRCUIT
Speedometer Circuit

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-38
TECHNICAL DESCRIPTION (COMMENT)
The engine-ECU and its associated components, the
combination meter assembly, the wiring harness, or
the connector(s) may be defective.
TROUBLESHOOTING HINTS
•Malfunction of the vehicle speed sensor
•Malfunction of the engine-ECU
•Malfunction of the combination meter assembly
•The wiring harness or connectors may have
loose, corroded, or damaged terminals, or
terminals pushed back in the connector.
DIAGNOSIS PROCEDURE
STEP 1. MUT-II/III actuator test
(1) Connect the MUT-II/III to the diagnosis connector.(2) Use the MUT-II/III to enter simulated vehicle
speed.
Q: Does the speedometer show that simulated vehicle
speed?
YES :
Go to Step 6.
NO : Go to Step 2.
STEP 2. Check the output shaft speed sensor.
(MUT-II/III diagnosis code)
(1) Connect MUT-II/III to the diagnosis connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the automatic transmission system
diagnosis code.
Q: Is automatic transmission system diagnosis code
23 set?
YES :
Refer to P.23A-38.
NO : Go to Step 3.
AC304777
Steering shaft
AB
MB991502

AC304950
MB991911
16-PIN
MB991827 MB991824
AB

AC304777
Steering shaft
AB
MB991502

AC304950
MB991911
16-PIN
MB991827 MB991824
AB

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-49
DIAGNOSIS PROCEDURE
STEP 1. Check the fuel gauge circuit.
(1) Disconnect D-13 fuel gauge unit connector.
(2) Connect a test lamp (12 V − 3.4 W) via test
harness (MB991219) between the wiring harness
connector terminals 1 and 2.
(3) Turn the ignition switch to the "ON" position.
Q: Does the test lamp illuminate?
YES :
Go to Step 4.
NO : . Go to Step 2.
STEP 2. Connector check: Combination meter
connector C-06, fuel gauge unit connector D-13
Q: Is combination meter connector C-04, fuel gauge
unit connector D-13 in good condition?
YES :
Go to Step 3.
NO : Repair or replace the damaged
component(s).
STEP 3. Check the wiring harness between
combination meter connector C-06 (terminal 51)
and fuel gauge unit connector D-13 (terminal 1).
AC305320
AB
Test lamp
(12 V - 3.4 W)
MB991219
Harness side
Fuel gauge
Earth
AC303798
Connector: C-04

Harness side
AT
AC303871
Connector: D-13

Harness sideD-13 (B)
AI
AC303917
D-13 (B) Connector: D-13

Harness side
AH
AC303798
Connector: C-06

Harness side
C-06 (L)
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
AV
AC303814AU
Connector: C-06

Harness side
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
C-06 (L)

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-54
INSPECTION PROCEDURE 6: Combination meter does not work. (the instruments do not work)
TECHNICAL DESCRIPTION (COMMENT)
The cause is thought to be malfunction of the power,
earth circuitry or combination meter.
TROUBLESHOOTING HINTS
•Malfunction of the combination meter
•Damaged wiring harness or connectors
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet IGNITION
SWITCH (IG1)
COMBINATION
METER
CONTROL CIRCUIT BATTERY
RELAY
BOX
NOTELH drive vehicles
RH drive vehicles
Combination Meter Power Source Circuit

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-57
STEP 4. Voltage measurement at combination
meter connector C-04 to check the battery circuit
of power supply system to the combination
meter.
(1) Measure at combination meter connector C-04
without disconnecting the connector.
(2) Turn the ignition switch to “ON” position.
(3) Measure the voltage between terminal 9 and
earth.
OK: System voltageQ: Is the check result normal?
YES :
Go to Step 7.
NO : Go to Step 5.
STEP 5. Connector check: combination meter
connector C-04
Q: Is combination meter connector C-04 in good
condition?
YES :
Go to Step 6.
NO : Repair or replace the connector. Check to
see that all meters operate.
AC303798
Connector: C-04

Harness side
AT
AC303814
Connector: C-04

Harness side
AT
AC301541
Connector: C-04
(Harness side)
FA
AC303798
Connector: C-04

Harness side
AT
AC303814
Connector: C-04

Harness side
AT

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-58
STEP 6. Check the wiring harness between
combination meter connector C-04 (terminal 9)
and ignition switch (IG1).
NOTE: Prior to the wiring harness inspection, check
Junction block connectors C-210 and C-212, joint
connector C-03 , and repair if
necessary.
Q: Are the wiring harness between combination meter
connector C-04 (terminal 42) and ignition switch
(IG1) in good condition?
YES :
There is no action to be taken.
NO : Repair or replace the wiring harness. Check
to see that all meters operate.
AC303798AU
Connector: C-03, C-04
C-04
C-03 (B)
C-04 C-03 Harness side
AC303814
Connector: C-04

Harness side
AT
AC303809
Connector: C-210, C-212

C-212
C-210
C-210 Harness side
C-212
AX
Front view
AC303823
Connector: C-210, C-212

C-210
C-212Front view
Harness side
C-210
C-212
AU