oil MITSUBISHI LANCER EVOLUTION 2007 Service Repair Manual

STEERING - Power Steering Oil Pump37A-29
POWER STEERING OIL PUMP
REMOVAL AND INSTALLATION
Caution
After temporary tightening all bolts in * part, tighten in specific torque.
Pre-removal Operation
Power Steering Fluid Draining (Refer to P.37A-9.)Post-installation Operation
DPower Steering Fluid Supplying and Bleeding
(Refer to P.37A-9.)
DDrive Belt Tension Adjusting
(Refer to GROUP 11A – On-vehicle Service.)
22±4 N·m
8
40±5 N·m 18±3 N·m
3
45
2
5
22±4 N·m*
1 7
6
40±5 N·m* 22±4 N·m
Removal steps
1. Pressure switch connector
2. Drive belt (Refer to GROUP 11A.)
"BA3. Suction hose connection
"BA4. Pressure hose connection"AA5. O ring
6. Heat protecter
7. Oil pump assembly
8. Power steering pump bracket
INSTALLATION SERVICE POINTS
"AAO-RING INSTALLATION
No.ID×Width mm
111.0×1.9
213.0×1.9
21

STEERING - Power Steering Oil Pump/Power Steering Oil Hoses37A-30
"BAPRESSURE HOSE ASSEMBLY/SUCTION HOSE
REMOVAL
Install the pressure hose assembly and suction hose as
illustrated.
DISASSEMBLY AND REASSEMBLY
21±3 N·m
3
4
2 1
39±5 N·m
: Automatic transmission fluid DEXRONII
NOTE
Disassembly steps
1. Suction connector
2. O-ring3. Connector
4. Gasket
POWER STEERING OIL HOSES
REMOVAL AND INSTALLATION
Caution
1. Before removing the clock spring, always see GROUP 52B - Caution for Service and Air Bag
Module Clock Spring
2. If the vehicle is equipped with the Brembo disc brake, during maintenance, take care not to
contact the parts or tools to the caliper, because the paint of caliper will be scratched.
3. On the tightening section indicated in the mark (*), lightly tighten the nut first, and then finally
tighten it with the engine weight applied on the body.
Suction hose
Pressure hose
assembly
Marking
Notch

STEERING - Power Steering Oil Hoses37A-31

Pre-removal and Post-installation Operation
Power Steering Fluid Draining and Refilling (Refer to
P.37A-9.)
12±2 N·m
17
16
15
12
18±3 N·m
Crossmember
1
57±7 N·m
9
8 47
32 5
12±2 N·m15±3 N·m
18±2 N·m 12±2 N·m
49±10 N·m
52±7 N·m*
12±2 N·m
6
10
11
167±10 N·m
14 13
18
12±2 N·m
12±2 N·m
Removal steps
1. Oil reservoir
"BA2. Suction hose
3. Return hose
4. Return hose
5. Return tube
DStrut tower bar (Refer to GROUP 42.)
6. Return hose
DClock spring (Refer to GROUP 52B.)
DCrossmember bar
(Refer to GROUP 33A.)
DCenter member (Refer to GROUP 32.)
DFront exhaust pipe
(Refer to GROUP 15.)
7. Steering gear and joint connecting
bolt8. Rear roll stopper connecting bolt
9. Rear roll stopper
(Refer to GROUP 32.)
AA"10. Eye bolt
11. Gasket
"BA12. Pressure hose assembly
"AA13. O ring
14. Return hose
15. Return tube
AA"16. Return tube
17. O ring
DFront bumper (Refer to GROUP 51.)
DIntercooler (Refer to GROUP 15.)
18. Cooler tube assembly

STEERING - Power Steering Oil Hoses37A-32

Pre-removal and Post-installation Operation
Power Steering Fluid Draining and Refilling (Refer to
P.37A-9.)
12±2 N·m
15
12
18±3 N·m
Crossmember
1
57±7 N·m
9
8 4
7
32 5
12±2 N·m
15±3 N·m
18±2 N·m 12±2 N·m
49±10 N·m
52±7 N·m*
12±2 N·m
6
10
11
167±10 N·m
14
13
12±2 N·m
Removal steps
1. Oil reservoir
"BA2. Suction hose
3. Return hose
4. Return hose
5. Return tube
DStrut tower bar (Refer to GROUP 42.)
6. Return hose
DClock spring (Refer to GROUP 52B.)
DCrossmember bar
(Refer to GROUP 33A.)
DCenter member (Refer to GROUP 32.)
DFront exhaust pipe
(Refer to GROUP 15.)7. Steering gear and joint connecting
bolt
8. Rear roll stopper connecting bolt
AA"9. Eye bolt
10. Gasket
"BA11. Pressure hose assembly
"AA12. O ring
AA"13. Return tube
14. O ring
DFront bumper (Refer to GROUP 51.)
DIntercooler (Refer to GROUP 15.)
15. Cooler tube assembly

STEERING - Power Steering Oil Hoses37A-33
REMOVAL SERVICE POINT
AA"EYE BOLT/RETURN TUBE REMOVAL
1. Loosen the crossmember mounting bolts and nuts, and
lower the crossmember to a position so that the eye bolts
or return tube at the steering gear side can be removed.
NOTE
In this case, do not remove the crossmember
mounting bolts and nuts.
2. Remove the eye bolts or return tube.
INSTALLATION SERVICE POINTS
"AAO RING INSTALLATION
No.ID×Width mm
111.0×1.9
213.0×1.9
"BAPRESSURE HOSE ASSEMBLY/SUCTION HOSE
INSTALLATION
Install the pressure hose assembly and suction hose as
illustrated.
1
2
Suction hose
Pressure hose
assembly
Marking
Notch

BODY -Window Glass42-9
WINDOW GLASS
ADHESIVE
ItemsSpecified adhesive
Windshield3M ATD Part No. 8609 Super Fast Urethane Auto Glass Sealant or
il tRear window glass
p
equivalent
SPECIAL TOOLS
ToolNumberNameUse
MB990480Window glass
holderRemoval and Installation of Window Glass
MB990784Ornament removerRear Window Lower Molding Removal
WINDOW REPAIR
The following glass parts are installed with a liquid urethane
adhesive method:
DWindshield
DRear window glass
ITEMS NEEDED
NameRemarks
Adhesive3M ATD Part No. 8609 Super Fast Urethane Auto Glass Sealant or
equivalent
Primer3M ATD Part No. 8608 Super Fast Urethane Primer or equivalent
SpacersAvailable as service part
DamAvailable as service part
Anti-rust solvent (or Tectyl 506T...Valvoline Oil
Company)For rust prevention
Isopropyl alcoholFor grease removal from bonded surface
Steel piano wireDia. y length...0.6mm 1m For cutting adhesive
Adhesive gunFor pressing-out adhesive

BODY -DoorsBODY -Doors42-19
DOORS
SERVICE SPECIFICATIONS
ItemsStandard value
Door outside handle play mmFront2.3±2.1py
Rear1.3±1.7
Power window operating current (power supply 14.5±0.5 V, 25_C) A5±1
Door inside handle play mmFront9.6±9.2py
Rear9.0±9.2
ADHESIVE
ItemsSpecified sealantRemark
Waterproof film3M ATD Part No. 8625 or equivalentRibbon sealer
SPECIAL TOOLS
ToolNumberNameUse
MB990784Ornament removerDoor trim removal
MB990480Window glass
holderRemoval of power window regulator and motor
assembly
MB990900 or
MB991164Door hinge
adjusting wrenchAdjustment of door fit
A
MB990925
A: MB990939Bearing & oil seal
installer set
A: Brass barAdjustment of door striker
MB990211Slide hammer
A
BB990241
MB990241
A: MB990243Axle shaft puller
A: Body puller

51-1
EXTERIOR
CONTENTS
FRONT BUMPER 2....................
ADHESIVE 2..............................
FRONT BUMPER 2........................
REAR BUMPER 6.....................
SIDE AIR DAM, MOLDING AND
GARNISH 8...........................
SPECIAL TOOL 8.........................
ADHESIVE 8..............................
SIDE AIR DAM MOLDING GARNISH 9.....
REAR SPOILER 11....................
ADHESIVE 11.............................REAR SPOILER 12........................
WINDSHIELD WIPER AND WASHER 13.
SERVICE SPECIFICATIONS 13.............
TROUBLESHOOTING 13...................
ON - VEHICLE SERVICE 13.................
WINDSHIELD WIPER AND WASHER 14......
MARKS 20............................
OUTSIDE MIRROR 23.................
SPECIAL TOOL 23........................
OUTSIDE MIRROR 23......................

EXTERIOR -Front Bumper51-3
DISASSEMBLY AND REASSEMBLY
18
5
18
173
14
13
18
Clip
Clip Clip
Section A – A
Section B – B
Section C – C
4
7
62
10
9
3 15
16
12 13
145
aa
b
b1116
1718
8 c
c
12
1
Disassembly steps
1. Front bumper plate
"CA2. Front bumper center net
3. Front bumper lower plate
4. Three - diamond mark
5. Front bumper upper reinforcement as-
sembly
6. License plate garnish
7. License plate bracket
AA""BA8. Rivet
9. Front bumper side blade and front cen-
ter reinforcement assembly10. Front bumper side blade
11. Front bumper center reinforcement
DWater spray hose and nozzle
(Refer to GROUP 15.)
12. Bezel net
13. Inner bracket
14. Front bumper bezel
15. Oil cooler duct
16. Front bumper side net
AB""AA17. Front air dam
18. Front bumper face

EXTERIOR -Rear Spoiler51-12
REAR SPOILER
ADHESIVE
ApplicationBrand
Rear spoilerDouble-sided tape [15 mm width 1.2 mm thickness, 30 mm width 1.2 mm
thickness]
REAR SPOILER
REMOVAL AND INSTALLATION
1
12
3
2
5.2±0.2 N·m
5.2±0.2 N·m5.2±0.2 N·m
5.2±0.2 N·m
A A
B
B
Steel plate hook
2
Claw
2
3
3 3
Double-sided tape:
Generic products: A : 15mm width, 1.2mm thickness,
B : 30mm width, 1.2mm thickness Section A – A
Section B – BA
B
Removal steps
DTrunk lid bumper
(Refer to Group 42.)
1. Gasket
2. Cap
A
A""
AA3. Rear spoilerNOTE:
The removal and installation service points are the
same as SIDE AIR DAM , MOLDING AND GARNISH.
(Refer to P.51-10)