rims MITSUBISHI LANCER EVOLUTION 2007 Service Repair Manual

MANUAL TRANSMISSION -4WD-ECU with ACD and AYC>22A-55
4WD-ECU AYC>
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
DCowl Side Trim Removal and Installation. (Refer to GROUP 52A - Trims.)
DFront floor Console Removal and Installation. (Refer to GROUP 52A - Floor Console.)
4.9¶0.9 Nm
4WD-ECU
4.9¶0.9 Nm
4WD-ECU

BODY -Doors42-30
REMOVAL SERVICE POINTS
AA"DOOR INSIDE HANDLE COVER REMOVAL
1. Insert the driver into the tapping screw cap end of the
door inside handle cover and pry the cap the way shown
in the illustration to remove the cap, and then unscrew
the tapping screw.
2. As shown in the illustration, insert the special tool between
the door inside handle cover and door inside handle,
and then disengage the claws of the door inside handle
cover and door inside handle.
3. Insert the special tool into the door inside handle cover
end, and then pry and remove the door inside handle
cover.
AB"CLIP REMOVAL
Use a cloth to remove the clip as shown in the illustration.Tapping screw cap
MB990784 Door inside handle cover
A
AB
B
Door inside
handle cover
Door inside
handle cover ClawClaw
Claw Door trimSection A - ASection B - B
Door inside
handle coverSpecial tool
insertion
position

52A-2
INTERIOR
CONTENTS
SPECIAL TOOL 3............................
INSTRUMENT PANEL* 3......................
FRONT FLOOR CONSOLE 10................
REAR FLOOR CONSOLE 12..................
TRIMS 15....................................
HEADLINING 17..............................SEAT 19.....................................
Front Seat 19..................................
Rear Seat 22..................................
SEAT BELT 25...............................
Front Seat Belt 25.............................
Rear Seat Belt 26..............................
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from rendering
the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are
indicated in the table of contents by an asterisk (*).

INTERIOR -Special Tool/Instrument Panel52A-3
SPECIAL TOOL
ToolNumberNameApplication
MB990784Ornament removerRemoval of switches and trims
INSTRUMENT PANEL
REMOVAL AND INSTALLATION
The following bolts and screws are used for installing the instrument panel.
Bolts and screws are indicated as marks shown in the illustration in the sections of “Removal and Installation”
and “Disassembly and Reassembly.”
NameMarkDimensions mm
(screw diameter x
screw length)ColorShape
Tapping screwa5×16Black
b5×16-
c5×12-
Bolt with washerd6×16-
e6×12-

INTERIOR -Trims52A-15
TRIMS
REMOVAL AND INSTALLATION
NOTE
Refer to GROUP42 for more information regarding door trim.
8
44±10 N•m
11
1 2649510
1312
3
7
15
16
14
Removal steps
1. Front scuff plate
2. Cowl side trim
3. Rear scuff plate
4. Front door opening trim
5. Rear door opening trim
AA"6. Front pillar trim
7. Center pillar trim, lower
8. Front seat belt connection9. Center pillar trim, upper
10. Rear pillar trim
11. Rear shelf trim
12. Speaker garnish
13. Retractor trim
14. Partition board
15. Rear end trim
16. Trunk side trim

INTERIOR -Trims52A-16
CLIP POSITION
NOTE
: Clip position
: Claw position
Section B - B
Section C - C
Section D - DSection E - ESection A - A
A ABB
C CC
CD
ClipFront pillar trim
Rear pillar trimFront scuff plate,
Rear scuff plate
Speaker garnish
Section F - F
Rear shelf
trim E
E
Front pillar trim,
Center pillar trim,
upper,
Rear pillar trim
Headlining
BBB
D
F
F
B
GG
Section G - G
Rear end trimClip
Clip
ClipClip
ClipClip H
HI
I
Section H - HSection I - I
Retractor trimRetractor trim
Craw
Craw

INTERIOR -Trims/Headlining52A-17
REMOVAL SERVICE POINT
AA"FRONT PILLAR TRIM REMOVAL
Release the clip to pull towards the direction shown in the
illustration and remove the front pillar trim.
HEADLINING
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Removal and Installation of Front Pillar Trim, Center
Pillar Trim, upper, Rear Pillar Trim (Refer to P.52A-15.)
12
3 4 56
45
Removal steps
1. Assist grip
2. Room lamp assembly
3. Front room lamp
AA"4. Sunvisor holder5. Sunvisor assembly
DFront floor console assembly
(Refer to P.52A-10.)
AB"6. Headlining
Section A – A
Front pillar trim
A
AFront pillar trim
Instrument
panel

CHASSIS ELECTRICAL -Roof Antenna/Defogger54A-42
ROOF ANTENNA
REMOVAL AND INSTALLATION
pre-removal and Post-installation Operations
DFront Pillar trim, Rear Pillar Trim and Lower/Upper Center Pillar Trim Removal and Installation (Refer to GROUP 52A -
Trims.)
DAssist Step Removal and Installation (Refer to GROUP 52A - Head Lining.)
DFront Room Lamp and Rear Room Lamp Removal and Installation
DHead Lining Removal and Installtion (Refer to GROUP 52A - Head Lining.)
1
2
3
Removal steps
1. Antenna pole
2. Roof antenna base
DInstrument panel (Refer to GROUP
52A - Instrument Panel.)3. Antenna feeder cable
DEFOGGER
TROUBLESHOOTING
Refer to GROUP 55.