warning MITSUBISHI MIRAGE 2014 6.G Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2014, Model line: MIRAGE, Model: MITSUBISHI MIRAGE 2014 6.GPages: 460, PDF Size: 20.86 MB
Page 180 of 460
3-92 Features and controls
3
NOTETire inflation pressures vary with the ambient tempera-
ture. If the vehicle is subjected to large variations in ambi-
ent temperature, the tire inflation pressures may be under-
inflated (causing the warning light come on) when the
ambient temperature is relatively low. If the warning light
comes on, adjust the tire inflation pressure.Whenever the tires and wheels are replaced with
new ones
N00532900153
If new wheels with new tire inflation pressure sensors are
installed, their ID codes must be programmed into the tire pres-
sure monitoring system. Have tire and wheel replacement per-
formed by an authorized Mitsubishi Motors dealer to avoid the
risk of damaging the tire inflation pressure sensors. If the
wheel replacement is not done by an authorized Mitsubishi
Motors dealer, it is not covered by your warranty.
General information
N00533000236
Your tire pressure monitoring system operates on a radio fre-
quency subject to Federal Communications Commission
(FCC) Rules (For vehicles sold in U.S.A.) and Industry Canada
Rules (For vehicles sold in Canada). This device complies with
part 15 of FCC Rules and Industry Canada licence-exempt
RSS standard(s).
Operation is subject to the following two conditions.
This device may not cause harmful interference
This device must accept any interference received, includ-
ing interference that may cause undesired operation.
CAUTION
!The use of non-genuine wheels will prevent the
proper fit of the tire inflation pressure sensors,
resulting air leakage or damage of the sensors.
WA R N I N G
!Changes or modifications not expressly approved by
the manufacturer for compliance could void the
user’s authority to operate the equipment.
BK0162600US.book 92 ページ 2013年3月22日 金曜日 午後2時41分
Page 191 of 460
Features and controls
3-103
3
Fuel remaining warning displayWhen the remaining fuel level runs low (one segment is dis-
played), the last segment of the fuel gauge flashes when the
ignition switch is turned to the “ON” position or the operation
mode is changed to ON.
When the remaining fuel level very runs low (no segments dis-
played), “ ” and the bar graph flash.
If the warning display appears, refuel as soon as possible.NOTEOn hills or curves, the display may be incorrect due to the
movement of fuel in the tank.
Service reminder
N00556700227
Displays the approximate time until the next recommended
periodic inspection. “---” is displayed when the inspection time
has arrived.NOTEThe service reminder time can be modified by an autho-
rized Mitsubishi Motors dealer, to adjust for severe usage,
etc. Refer to “Severe maintenance schedule” in your vehi-
cle’s Warranty and Maintenance Manual. For further
information, please contact your authorized Mitsubishi
Motors dealer.
1. Shows the time until the next periodic inspection.NOTEShows the distance in units of 100 miles (100 km) and the
time in units of 1 month.
CAUTION
!Running out of gas could damage the catalytic con-
verter. If the warning display appears, refuel as soon
as possible.
Distance
Month
BK0162600US.book 103 ページ 2013年3月22日 金曜日 午後2時41分
Page 197 of 460
Features and controls
3-109
3 Indicator and warning light package
N00519800849
1- High beam indicator → P. 3 - 1 1 0
2- Electric power steering system warning light → P.3-75
3- Tire pressure monitoring system warning light (if so
equipped) → P.3-88
4- Turn signal indicators/Hazard warning lights → P. 3 - 1 1 0
5- Front fog light indicator (if so equipped) → P. 3 - 1 1 0
6- Door-ajar warning light → P. 3 - 1 1 4
7- Supplemental Restraint System (SRS) warning light
→ P.2-44
8- High coolant temperature warning light (red) → P. 3 - 1 1 3
9- Low coolant temperature indicator (green) → P. 3 - 1 1 0
10- Oil pressure warning light → P. 3 - 1 1 3
11- Engine malfunction indicator (“SERVICE ENGINE SOON”
or “Check engine light”) → P. 3 - 1 1 212- Charging system warning light → P. 3 - 1 1 3
13- Brake warning light → P.3-111
14- Anti-lock braking system warning light → P.3-73
15- Multi-information display → P.3-98
16- Driver ’s seat belt reminder/warning light → P.2-18
17- Cruise control indicator (if so equipped) → P.3-81
18- Active stability control (ASC) indicator/warning light →
P.3-78, 3-79
19- Active stability control (ASC) OFF indicator/warning light
→ P.3-78, 3-79
20- ECO indicator → P. 3 - 1 1 0
21- For details, refer to “Warning activator” on page 3-21 (if so
equipped)
22- For details, refer to “Warning activator” on page 3-21 (if so
equipped)
BK0162600US.book 109 ページ 2013年3月22日 金曜日 午後2時41分
Page 198 of 460
3-110 Features and controls
3Indicators
N00519900127
Turn signal indicators/Hazard warning lights
N00520000216
The arrows will flash in time with the corresponding exterior
turn signals when the turn signal lever is used.
Both arrows will flash when the hazard warning flasher switch
is pressed.NOTEIf the indicator flashes faster than usual or if the indicator
stays on without flashing, check for a malfunctioning turn
signal light bulb or turn signal connection.High beam indicator
N00520100086
A blue light comes on when the headlights are on high beam.Front fog light indicator
(if so equipped)
N00520200175
This indicator comes on while the front fog lights are on.Low coolant temperature indicator - green
N00575600010
This indicator comes on in green while the coolant temperature
is low.NOTEWhen the indicator goes out, this should be used as a
rough indication of when the heating starts working.
ECO indicator
N00568800036
This indicator comes on while fuel-efficient driving is
achieved.
BK0162600US.book 110 ページ 2013年3月22日 金曜日 午後2時41分
Page 199 of 460
Features and controls
3-111
3 Wa r n i n g l i g h t s
N00520300147
Brake warning light and buzzer
N00520400526
This light comes on when the ignition switch is turned to the
“ON” position (engine off) or the operation mode is put in ON.
When the engine is started, the light should go off a few sec-
onds later.
The warning light also illuminates after starting the engine
under the following conditions.
When the parking brake is still applied.
When the brake fluid level is low.
When the brake system circuit is not working properly.
When the vehicle is moving at more than 5 mph (8 km/h) and
the parking brake applied, a buzzer will sound to inform the
driver that the parking brake is not properly release.
Before driving, be sure that the parking brake is fully released
and the brake warning light is off.
CAUTION
!If the brake warning light and the Anti-lock braking
system warning light are illuminated at the same
time, the braking force distribution function will not
operate, the vehicle may be destabilized during sud-
den braking under the following conditions.
• When the brake warning light does not go out even
when the parking brake is released.
• When the brake warning light stays on while driv-
ing.If the above occurs, avoid sudden braking and high-
speed driving. Park the vehicle in a safe place, and
contact an authorized Mitsubishi Motors dealer or a
repair facility of your choice as soon as possible.
The vehicle should be brought to a halt in the follow-
ing manner when brake performance is deterio-
rated.
• Confirm that the vehicle slows down when you
press down on the brake pedal harder than usual.
In some cases, the brake pedal may go all the way
to the floor.
• Should the brakes fail, use engine braking to
reduce your speed and slowly apply the parking
brake.
Depress the brake pedal to illuminate the stop
lights and to alert the vehicles behind you.
BK0162600US.book 111 ページ 2013年3月22日 金曜日 午後2時41分
Page 201 of 460
Features and controls
3-113
3
Charging system warning light
N00520600313
This light comes on in the event of a malfunction in the charg-
ing system or when the ignition switch is turned to the “ON”
position (engine off) or the operation mode is put in ON. When
the engine is started, the light should go out. Check to make
sure that the light has gone out before driving.Oil pressure warning light
N00520700170
This light comes on when the engine oil pressure is below nor-
mal. If the light stays on while driving, stop the engine as soon
as possible. Do not run the engine until the cause of the low oil
pressure is corrected.
High coolant temperature warning light - red
N00575700011
This light comes on in red if the coolant temperature becomes
excessively high.NOTEThe high coolant temperature warning light may illumi-
nate when the vehicle has been driven at high speeds or on
hilly roads. This illuminating does not necessarily indicate
a problem. It should stop if you keep the engine running
for a while or continue driving the vehicle.
CAUTION
!If the warning light stays on while the engine is run-
ning, park your vehicle in a safe place as soon as
possible and contact an authorized Mitsubishi
Motors dealer or a repair facility of your choice to
have the system checked.
CAUTION
!If this light comes on when the engine oil level is not
low, have your vehicle checked at an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.This warning light does not show the amount of oil
in the crankcase. This can only be determined by
checking the oil level with the dipstick with the
engine turned off.
CAUTION
!If the light comes on during vehicle operation, it
indicates that the engine is possibly overheating.
Continued driving could make the engine fail.
Immediately stop the vehicle in a safe place and take
appropriate action. (Refer to “Engine overheating”
on page 6-5.)
BK0162600US.book 113 ページ 2013年3月22日 金曜日 午後2時41分
Page 202 of 460
3-114 Features and controls
3
Door-ajar warning light and buzzer
N00520900329
This light comes on when any door or the liftgate is open or not
completely closed.
When the vehicle is moving at more than 5 mph (8 km/h) and
any door or the liftgate is open or ajar, a tone will sound 4
times to inform the driver that any door or the liftgate is not
properly shut.NOTEWhen the auto cut-out function of the doom light is been
activated, the light goes out automatically after about 30
minutes.
Refer to “Dome light” on page 3-162.
Combination headlights and dimmer switch
N00522500736
HeadlightsRotate the switch to operate the lights.
The combinations of switch operations and illuminated lights
differ in accordance with the following conditions.
Except for vehicles equipped with daytime running lights
CAUTION
!Before driving, make sure that the door-ajar warn-
ing light is off.
OFF All lights off
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
BK0162600US.book 114 ページ 2013年3月22日 金曜日 午後2時41分
Page 207 of 460
Features and controls
3-119
3
NOTEA light in the instrument panel flashes to show when the
turn signal lights are working properly.
If this light flashes faster than usual, check for a burned
out turn signal light bulb or malfunctioning connection in
the signal.
If the panel light does not come on when the lever is
moved, check for a blown fuse or a burned out bulb in the
panel.
Have the system inspected by your authorized Mitsubishi
Motors dealer or a repair facility of your choice.
It is possible to modify functions as follows:
• Deactivate the turn signal light 3-flash function for lane
changes.
• Adjust the time required to operate the lever for the 3-
flash function.
• Changing of the tone of a sounding buzzer as the turn
signal lights flash.
See your authorized Mitsubishi Motors dealer for details.
Hazard warning flasher switch
N00522700318
If you press the flasher switch, the turn signals will flash inter-
mittently, and so will the hazard warning lights. This is an
emergency warning system and should not be used when the
vehicle is in motion, except for emergencies.
If you need to leave your vehicle, the flashers will keep work-
ing after the ignition switch is removed or the operation mode
is put in OFF.NOTEIf the flashers are used for several hours, the battery will
run down. This could make it difficult or impossible to
restart your vehicle.
BK0162600US.book 119 ページ 2013年3月22日 金曜日 午後2時41分
Page 217 of 460
Features and controls
3-129
3
For detail of the Bluetooth
® 2.0 interface, refer to the fol-
lowing web site:
[For vehicles sold in U.S.A.]
You can refer to the MITSUBISHI MOTORS NORTH
AMERICA web site.
[For vehicles sold in Canada]
You can refer to the MITSUBISHI MOTORS web site.
Please read and agree to the “Warning about Links to the
Web Sites of Other Companies”. Links may connect to
websites other than MITSUBISHI MOTORS.
http://www.mitsubishi-motors.com/en/prod-
ucts/index.html
Software updates by cellular phone/digital audio device
manufacturers may change/alter device connectivity.
Steering control switch and microphone → P. 3 - 1 2 9
Voice recognition function → P. 3 - 1 3 1
Useful voice commands → P.3-132
Speaker enrollment function → P. 3 - 1 3 4
Connecting the Bluetooth
® 2.0 interface and the Bluetooth
®
device→ P. 3 - 1 3 5
Operating a music player connected via Bluetooth
® → P. 3 - 1 4 0
How to make or receive hands-free calls → P.3-140
Phonebook function → P.3-144
Steering control switch and microphone
N00564000072
1- Volume up button
2- Volume down button
3- SPEECH button
4- PICK-UP button
5- HANG-UP button
6- Microphone
BK0162600US.book 129 ページ 2013年3月22日 金曜日 午後2時41分
Page 342 of 460
6-2 For emergencies
6If the vehicle breaks down
N00836300233
If your vehicle breaks down on the road, move to the shoulder
and turn on the hazard warning flashers. If there is no shoulder,
or the shoulder is not safe, drive in the right lane slowly with
the hazard lights flashing until you come to a safe stopping
place. Keep the flashers flashing.If the engine stops/failsIf the engine stops, there will be no power assist to the steering
and brakes, making these difficult to use.
The brake booster will not work, so the brakes will not
grip well. The brake pedal will be harder to press than
usual.
Since there is no power steering assist, the steering wheel
will be hard to turn.When the engine fails at the intersectionGet help from your passengers, bystanders, etc. to push the
vehicle and move it to a safe area.
Jump-starting the engine
N00836400768
If the engine cannot be started because the battery is weak or
dead, you can start it with the battery from another vehicle
using jumper cables.NOTEDo not use jumper cables if they have damage or corro-
sion.
1. Take off any metal jewelry such as watch bands or brace-
lets that might create an accidental electrical contact.
2. Position the vehicles close enough together so that the
jumper cables can reach, but be sure the vehicles aren’t
touching each other.
WA R N I N G
!To reduce the risk of igniting flammable gas that
may be emitted from the battery, carefully read this
section before jump-starting the vehicle.Do not try to start your vehicle by pushing or tow-
ing. This can cause an accident resulting in serious
injury or death and can damage the vehicle.
CAUTION
!Check the other vehicle. It must have a 12-volt bat-
tery. If the other system isn’t 12-volt, both systems
can be damaged.
BK0162600US.book 2 ページ 2013年3月22日 金曜日 午後2時41分