lock MITSUBISHI MIRAGE 2017 6.G Repair Manual

Cargo loads 6-10 Driving safety
6
N00629700435 N00630300082
To determine the cargo load capacity for your vehicle, subtract the
weight of all vehicle
occupants from the vehi
cle capacity weight.
For additional information, if needed, refer to “Steps for Determining Correct Load Limit” on page 6-8. DO NOT USE the Gross Vehicle Weight Rat- ing and Gross Axle Weight Rating numberslisted on the safety certification label (A) as the guide for pass
engers and/or cargo
weight.
N00630401136
Cargo loads Cargo load precautions
WA R N I N G To reduce the risk of serious injury or death, the combined weights of the driver,passengers and cargo and must neverexceed the vehicle capacity weight. Exceeding the vehicle capacity weight will adversely affect ve
hicle performance,
including handling and braking, and may cause an accident. Do not load cargo or luggage higher than the top of the seatback. Be sure that yourcargo or luggage cann
ot move when your
vehicle is in motion. Having either the re
ar view blocked, or
your cargo being thrown
inside the cabin
if you suddenly have to brake can cause a serious accident or
injury or death.
Put cargo or luggage in the cargo area of your vehicle. Try to spread the weightevenly.
Loading cargo on the roof
WA R N I N G Weight placed on the
roof of the vehicle
will raise the vehicle’ and adversely affect
its handling charac-
teristics. As a result, driving errors oremergency maneuvers could lead to a loss of control and result in an accident. Drive slowly and avoid excessive maneuverssuch as sudden brak
ing or quick turning.
Make sure that the
weight of luggage and
the roof carrier do not exceed the maxi-mum roof load, 110 lb (50 kg). If the maxi-mum roof load is ex
ceeded, this could
cause damage to the ve
hicle or result in an
accident. The total weight of all occupants and lug- gage, including your r
oof load, must not
exceed the vehicle capacity weight. For more information, refer to “Tire and load- ing information placard” on page 11-3. Roof load is determined by adding the weight of the roof
carrier and the weight
of the luggage placed
on the roof carrier.
CAUTIONDo not load luggage directly onto the roof. Use a roof carrier that properly fits your vehicle. For installation, refer to the instruction man-ual provided with the roof carrier. Place the luggage on the carrier so that its weight is distri
buted evenly with the heaviest
items on the bottom. Do not load items that are wider than the roof carrier.WA R N I N G
BK0235100US.book 10 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

Heater without air conditioning function (if so equipped) 7-4 Comfort controls
7
Air flows mainly to the windshield and the door windows.
N00737700031
The heater can only be used while the engineis running.
N00737801042
N00737901043
When the ignition switch is in the “ON” posi- tion, select the blower speed by turning the blower speed selection dial.Turning the dial clockwise will increase the blower speed; turning
the dial counterclock-
wise will decrease it. When the dial is set tothe “OFF” position, all fan-driven airflow will stop.
NOTE
 With the mode selec
tion dial between the
“ ” and “ ” positions, air flows mainly to the leg area. With the mode selection dial between the “ ”and “ ” positions, air flows mainly to the windshield and the door windows.
Defroster position
Heater without air condi- tioning function
(if so equipped)

1- Temperature control dial 2- Blower speed selection dial 3- Electric rear win
dow defogger switch
 P. 5-80
4- Mode selection dial 5- Air selection lever
Blower speed selection dial

BK0235100US.book 4 ページ ２０１５年１１月２０日\b 5 Y

Heater without air conditioning function (if so equipped)
Comfort controls 7-5
7
N00738001067
Turn the temperature c
ontrol dial clockwise
to make the air warmer
. Turn it counterclock-
wise to make the air cooler.
N00738101071
To change the amount of air flowing from the vents, turn the mode
selection dial. Refer to
“Changing the mode sele
ction” on page 7-2.
N00738201056
Normally, use the outside air position to keep the windshield and side
windows clear and to
quickly remove fog or frost from the wind- shield. To change the air selection, use the air selec- tion lever.  “ ” Outside air  “ ” Recirculated air
If the outside air is dusty or contaminated in some way, use the recirculation position. Switch to the outside
air position every now
and then to keep the windows from fogging up.
N00738301057
Set the mode selection
dial to the “ ” posi-
tion and set the air selection lever to the out- side air position.
Temperature control dial

Mode selection dial

Air selection lever

CAUTION Using recirculated ai
r for a long time may
cause the windows to fog up.
Operating the system

Heating

BK0235100US.book 5 ページ ２０１５年１１月２０日\b 5 Y

Heater without air conditioning function (if so equipped) 7-6 Comfort controls
7
Turn the temperature control dial clockwise or counterclockwise to
the desired tempera-
ture. Select the desire
d blower speed to fit
your needs.
N00738401045
Set the mode selection
dial to the positions
shown in the illustration and set the air selec- tion lever to the outside air position. The air flow will be directed to the leg area and the upper part of the passenger compart-ment. Set the desired blower speed. Warm air flows to the leg area and unheated or slightly warm air (depending upon the position of the temperat
ure control dial) flows
to the upper part of the passenger compart-ment.
N00738501091
Set the mode selection dial (between “ ” windshield and door window. For ordinary defrosting Use this setting to ke
ep the windshield and
door windows clear of mist, and to keep the leg area heated (when driving in rain or snow). 1. Set the mode select
ion dial to the “ ”
CAUTION The engine speed may increase when the heating is operating. Since creeping will occur strongly if theengine speed becomes
high while the vehicle
with a CVT is stationa
ry, fully depress the
brake pedal to prevent the vehicle fromcreeping.NOTE
 For quick heating, set the blower speed at the 3rd position.
Combination of unheated air and heated air

Defrosting or defogging (wind-shield, door windows)

CAUTION For safety, make sure you have a clear view through all the windows.
BK0235100US.book 6 ページ ２０１５年１１月２０日\b 5 Y

Manual air conditioning (if so equipped)
Comfort controls 7-7
7
2. Set the air selection le
ver to the outside air
position.3. Select your desired
blower speed by turn-
ing the blower spee
d selection dial.
4. Select your desired
temperature by turn-
ing the temperature control dial.
For quick defrosting 1. Set the mode selection dial to the “ ” 2. Set the air selection le
ver to the outside air
position. 3. Set your blower to the maximum speed. 4. Set the temperature to the highest posi-tion.
N00730300344
The air conditioning can only be used whilethe engine is running.
N00730501327
N00736501215
When the ignition switch or the operation mode is in ON, select
the blower speed by
turning the blower speed selection dial.Turning the dial clockwise will increase the blower speed; turning
the dial counterclock-
wise will decrease it. When the dial is set tothe “OFF” position, all fan-driven airflow will stop.
NOTE
 To defog quickly, direct the air flow from the side vents toward the door windows.
Manual air conditioning
(if so
equipped)

1- Temperature control dial 2- Air conditioning switch 3- Blower speed selection dial 4- Electric rear window defogger
switch
 P.5-80
5- Mode selection dial 6- Air selection lever
Blower speed selection dial

BK0235100US.book 7 ページ ２０１５年１１月２０日\b 5 Y

Manual air conditioning (if so equipped) 7-8 Comfort controls
7
N00736601258
Turn the temperature control dial clockwise to make the air warmer
. Turn it counterclock-
wise to make the air cooler.
N00736701233
To change the amount of air flowing from the vents, turn the mode
selection dial. Refer to
“Changing the mode sele
ction” on page 7-2.
N00736801423
Normally, use the outside air position to keep the windshield and side windows clear and to quickly remove fog or frost from the wind-shield. To change the air selection, use the air selec- tion lever.  “ ” Outside air  “ ” Recirculated air
If the outside air is dusty or contaminated in some way, use the
recirculat
ion position.
Switch to the outside
air position every now
and then to keep the windows from foggingup.
Temperature control dial

NOTE
 While the engine coolant temperature is low, the temperature of the air from the heater will be cool/cold until
the engine warms up,
even if you have selected warm air with the dial.
Mode selection dial

Air selection lever

BK0235100US.book 8 ページ ２０１５年１１月２０日\b 5 Y

Manual air conditioning (if so equipped)
Comfort controls 7-9
7
N00731001488
Push the switch, and the air conditioning compressor will turn on. The air conditioningindicator light (A) will come on. Push the switch again and the air condition- ing compressor will stop and the indicator light (A) goes off.
N00731101304
Set the mode selection dial to the “ ” posi- tion and set the air sele
ction lever to the out-
side air position. Turn the temperature control dial clockwise or counterclockwise to
the desired tempera-
ture. Select the desire
d blower speed to fit
your needs.
N00731201376
1. Set the mode selection dial to the “ ” 2. Set the air selection le
ver to the outside air
position.3. Push the air conditioning switch. 4. Change the temperature by turning the control dial clockwise or counterclock-wise. 5. Set the desired blower speed.
CAUTION Using recirculated ai
r for a long time may
cause the windows to fog up.
Air conditioning switch

Operating the ai
r conditioning
system

Heating

NOTE
 For quick heating, set th
e blower speed at the
3rd position.
Cooling

CAUTION The engine speed may increase when the air conditioning (cooling or
heating) is operat-
ing. Since creeping will oc
cur strongly if the
engine speed becomes
high while the vehicle
with a CVT is stationary, fully depress the brake pedal to prevent the vehicle from creeping.
BK0235100US.book 9 ページ ２０１５年１１月２０日\b 5 Y

AM/FM electronically tuned radio with CD player (if so equipped) 7-20 Comfort controls
7
N00711901742 N00712001421
Turn the VOL switch clockwise to increase the volume; counterclockw
ise to decrease the
volume.The status will be displayed in the display.
N00712101709
1. Press the /MENU button to select BASS
 TREBLE
 FADER
 BAL-
ANCE
 Sound control mode off.
2. Turn the SEL switch either clockwise or counterclockwise to change the tone/bal- ance setting.The status will be di
splayed in the display.
To select the desired bass level.To select the desired treble level. To balance the volume from the F (front) and the R (rear) speakers. To balance the volume from the L (left) and the R (right) speakers.
N00734901925
Volume and tone control panel

1- PWR (On-Off)/VOL (Volume con-
trol)/SEL (Select) switch
2- Display 3-
/MENU (Mode change) button
4- SEL (Select) indicator 5-
(Return) button
To adjust the volume

To adjust the tone

BASS (Bass tone control)

TREBLE (Treble tone control)

FADER (Front/Rear balance con- trol)

BALANCE (Left/Right balance control)

NOTE
 When operation of turn
of the SEL switch is
enabled, the SEL indica
tor will appear on the
display.  When set to “0”, it will beep.  When the following ope
ration is performed,
this mode will be canceled. • The button is pressed. • The another mode
is selected.
• The any adjustment is not performed for more than 10 seconds.
 In a two-speakers vehi
cle, keep the FADER
setting in the middle position. Since no rearspeakers are connect
ed, adjusting the
FADER setting toward the “R” (rear) side will result in a loss of sound output.
Radio control panel and display

1- RADIO (AM/FM selection) button
BK0235100US.book 20 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

AM/FM electronically tuned radio with CD player (if so equipped)
Comfort controls 7-25
7
The CD player can display disc and track titles for discs with c
onverted disc and track
title information. Press the INFO button repeatedly to make selections in the following sequence: disc name
 track name
 normal
display mode. The CD player can display folder and file titles for discs with converted folder and fileinformation. Press the INFO button repeat- edly to make selections in the following sequence: folder name
 file name
 nor-
mal display mode. The CD player can display ID3 tag informa- tion for files that have been recorded with ID3 tag information.
1. Press the INFO button for 2 seconds or longer to switch to
the ID3 tag informa-
tion. 2. Press the INFO button repeatedly to make selections in the following sequence:album TAG
 track TAG
 artist TAG
 normal display mode.
N00702600010
Press the button to switch the clock mode. To exit the clock mode, press the button.
CD text
NOTE
 The display can show up to 11 characters. If a disc name or track name has more than 11characters, press the PAGE button to view the next 11 characters.  When there is no title information to be dis- played, the display
shows “NO TITLE”.
player cannot display
are shown as “•”.
MP3 titles ID3 tag information
NOTE
 To return from ID3 tag information to the folder name, press the INFO button again for 2 seconds or longer.  When there is no title information to be dis- played, the display shows “NO TITLE”.  The display can show up to 11 characters. If a folder name, track name
, or item of ID3 tag
information has more than 11 characters, press the PAGE button to view the next 11 characters.  Characters that the CD
player cannot display
are shown as “•”.
To display the clock

A- (Clock) button
NOTE
 While the clock mode is
selected, the display
will switch to the a
pplicable operation dis-
play whenever the CD player, external audioinput mode or radio, et
c. is operated. Then, if
no entries are made for 7 seconds, the dis- play will automatically return to the clockmode.Example CD player mode Clock mode
BK0235100US.book 25 ページ ２０１５年１１月２０日　金曜日　午後３時１２分

AM/FM electronically tuned radio with CD player (if so equipped) 7-26 Comfort controls
7
N00702701034
1. Press and hold the button and the clock display flashes. 2. Turn the SEL switch to adjust the “hours”digit. 3. When the “hours” digit is adjusted, press the button to flash
the “minutes” digit.
Turn the SEL switch to adjust the “min- utes” digit. 4. When the time is set, press the button to stop the clock display from flashing.
N00702801035
1. Press and hold the /MENU button for 2 seconds or longer. 2. Turn the SEL switch or press the
/MENU button several times to select
“Gracenote DB” and then press the SEL switch. 3. Turn the SEL switch to select “DB Ver-sion” and then press the SEL switch. The Gracenote DB vers
ion is displayed.
To adjust the clock

A- (Clock) button B- SEL (Select) switch C- SEL (Select) indicator D- (Return) button
NOTE
 When operation of turn of the SEL switch is enabled, the SEL indica
tor will appear on the
display.  When the following operation is performed, this mode will be canceled. • The button is pressed until you hear a beep. • The button is pressed. • The another mode is selected.  Reset the time after the battery terminals are disconnected an
d reconnected.
 Seconds do not appear
in the clock display,
but after adjusting the
“minutes” setting, the
clock begins to operate from 0 seconds.
To confirm the version number of the Gracenote DB (vehicles with a Bluetooth
® 2.0 interface)

A-
/MENU button
B- SEL (Select) switch C- SEL (Select) indicator D- (Return) button
BK0235100US.book 26 ページ ２０１５年１１月２０日　金曜日　午後３時１２分