coolant temperature MITSUBISHI MONTERO 1991 Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 611 of 1333
Removal (Montero)
1) Move temperature control lever to WARM position. Drain
coolant from vehicle. Disconnect heater hoses from heater unit. See
Fig. 1.
2) Remove lap heater ducts. Remove hood release bracket.
Using screwdriver, release tabs and remove left and right demister
grilles. Remove glove box frame attaching screws, and remove glove
box. Remove passenger lap heater duct.
3) Using screwdriver and shop towel, carefully pry at top
center of instrument cluster cover, and remove cover. Remove 2 screws
at bottom of instrument panel and one bolt at top of instrument panel.
Gently pull instrument cluster out, and disconnect speedometer cable
and electrical connections. Remove instrument cluster.
4) Remove 4 screws, and disconnect electrical connections on
back of instrument cluster. Remove instrument cluster. Handle
instrument cluster carefully. Instrument cluster can be damaged if
dropped.
5) Remove center console knobs and side screw plugs. Remove
screws, disconnect electrical connections and remove console. Remove 6
bolts and console bracket (center dash reinforcement). Disconnect
radio connections while removing console bracket.
6) Remove horn pad and steering wheel retaining nut. Mark
steering wheel and steering shaft for reassembly reference. Using
steering wheel puller, remove steering wheel.
7) Using screwdriver, carefully pry out dash plug at upper
center of dash panel. Remove 3 upper dash mounting nuts, one upper
screw above steering column, and 2 lower mounting screws. Remove dash
panel.
8) Remove control cables at heater unit. Remove heater unit
attaching screws. Remove heater ducts. Remove heater unit. Remove
heater control lever arm.
9) Remove heater control valve cover. Remove heater pipe and
heater control valve. Disconnect control arm linkage. Remove control
arm. Remove heater core by moving it sideways.
Installation
1) To install, reverse removal procedure. Insert heater hoses
fully into pipes, and clamp securely to prevent leaks. Connect heater
hoses with 1-1.2" (25-30 mm) overlap on outlet.
2) When filling radiator with coolant, first open heater
control valve fully and run engine to circulate coolant and discharge
air from inside heater and engine cooling system. Stop engine, and add
coolant.
3) Adjust all control cables. When installing heater hose
grommets, apply sealer. After installing heater control assembly,
ensure each lever operates smoothly.
Removal (Pickup & Ram-50)
1) Disconnect battery ground cable. Place heater control
lever to far right. Drain coolant. Using trim stick, pry out hazard
switch and remove electrical connection. Remove 4 instrument cluster
cover screws, and remove cover. Remove 4 instrument cluster screws.
Tilt instrument cluster out, and disconnect speedometer cable and
electrical connections. Remove cluster.
2) Remove fuse box cover and fuse box assembly. Remove glove
box. Remove defroster air ducts. Disconnect heater control cables.
Using trim stick, pry under and remove speaker grilles. Remove clock
or coin box in center of dash. Remove center dash hole cover (located
above clock).
3) Remove 2 center support cover screws, and remove cover.
Remove shift knob and 6 console attaching screws. Remove console.
Ensure all electrical connections are free of dash panel. Remove 3 top
nuts, one bolt above steering column, and side and lower attaching
Page 612 of 1333
screws. Remove dash panel.
4) Remove blower duct, center duct and defroster ducts. See
Fig. 2. Disconnect heater wiring harness from heater unit. Remove
heater center support brackets. Remove heater unit. Remove heater core
cover plate and joint hose. Remove heater core from heater unit.
Installation
1) To install, reverse removal procedure. Insert heater hoses
fully into pipes, and clamp securely to prevent leaks.
2) When filling radiator with coolant, first open heater
control valve fully and run engine to circulate coolant and discharge
air from inside heater and engine cooling system. Stop engine, and add
coolant.
3) Adjust all control cables. When installing heater hose
grommets, apply sealer. After installing heater control assembly,
ensure each lever operates smoothly.
HEATER CONTROL PANEL
Removal (Montero)
1) Remove heater control knob and heater fan switch knob.
Remove center console. Remove defroster nozzle at temperature control
cable side.
2) Remove lap heater duct and glove box stopper, and push
glove box forward and down. Disconnect inside/outside control cable
from blower assembly.
3) Disconnect control cables from heater unit. Remove heater
control panel mounting screws, and pull out panel slightly. Disconnect
heater fan switch harness connectors. Remove heater control panel.
Remove heater fan switch from heater control panel.
Installation
1) Place air outlet change-over lever at closed position.
With heater side air outlet change-over damper lever in position,
connect inner cable to lever, and secure cable casing using clips.
2) Place heater control lever at OFF position. With heater
control lever in position, connect inner cable to lever, and secure
cable casing using clips.
3) Place inside/outside air change-over lever at INSIDE
position. With heater side inside/outside air change-over damper lever
in position, connect inner cable to lever, and secure cable casing
using clips.
4) Set control lever to each position to check for correct
operation. If lever does not operate correctly, adjust by moving outer
wire at clipped point. Ensure each control lever moves smoothly. If
any noise or stiff movement exists, apply multipurpose grease to all
moving parts.
NOTE: When mounting heater control panel to instrument panel,
tighten upper bolts to instrument panel so they also secure
center panel.
Removal & Installation (Pickup & Ram-50)
Remove cluster panel. Remove all control cables at heater.
Remove heater control panel. To install, reverse removal procedure.
Adjust cables as necessary.
WIRING DIAGRAMS
Page 620 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual Brake On/Off (BOO) Switch ................... Cruise Control Systems\
Engine Performance
Shift Int](/img/19/57332/w960_57332-619.png "MITSUBISHI MONTERO 1991 Owners Manual Brake On/Off (BOO) Switch ................... Cruise Control Systems\
Engine Performance
Shift Int")
Brake On/Off (BOO) Switch ................... Cruise Control Systems\
Engine Performance
Shift Interlock Systems
Buzzer Module ...................................... Warning Systems
Camshaft Position (CMP) Sensor .................. Engine Performance\
Central Control Module ........................... Anti-Theft System
Clockspring ............................... Air Bag Restraint System
Cruise Control Systems
Steering Column Switches
Clutch Pedal Position Switch .............................. Starters
Clutch Start Switch ....................................... Starters
Combination Meter ......................... Analog Instrument Panels
Constant Control Relay Module (CCRM) ............ Engine Performance\
Electric Cooling Fans
Convenience Center .............................. Power Distribution
Illumination/Interior Lights
Convertible Top Motor ........................ Power Convertible Top
Convertible Top Switch ....................... Power Convertible Top
Crankshaft Position (CKP) Sensor ................ Engine Performance\
Cruise Control Module ....................... Cruise Control Systems
Cruise Control Switch ....................... Cruise Control Systems
Condenser Fan Relay(s) ....................... Electric Cooling Fans\
Data Link Connector (DLC) ....................... Engine Performance\
Daytime Running Lights Module ............... Daytime Running Lights
Exterior Lights
Defogger Relay ................................ Rear Window Defogger
Diagnostic Energy Reserve Module (DERM) ... Air Bag Restraint System\
Discriminating Sensor (Air Bag) ........... Air Bag Restraint System\
Distributor ..................................... Engine Performance
Door Lock Actuators ............................... Power Door Locks
Remote Keyless Entry
Door Lock Relay(s) ................................ Power Door Locks\
Electrochromic Mirror ................................ Power Mirrors
Electronic Level Control (ELC)
Height Sensor .............................. Electronic Suspension
Electronic Level Control (ELC) Module ........ Electronic Suspension\
Engine Coolant Temperature (ECT)
Sending Unit ............................ Analog Instrument Panels
Engine Coolant Temperature (ECT) Sensor ......... Engine Performance\
Engine Control Module ........................... Engine Performance
Generators & Regulators
Starters
ETACS ECU .......................................... Warning Systems
Power Windows
Remote Keyless Entry
Evaporative (EVAP) Emissions Canister ........... Engine Performance\
EVAP Canister Purge Solenoid .................... Engine Performance
EVAP Canister Vent Solenoid ..................... Engine Performance
Exhaust Gas Recirculation (EGR) Valve ........... Engine Performance\
Fuel Tank Vacuum Sensor ......................... Engine Performance
Fog Lights ....................................... Headlight Systems
Daytime Running Lights
Fog Light Relay .................................. Headlight Systems
Daytime Running Lights
Fuel Door Release Solenoid ................. Power Fuel Door Release
Fuel Gauge Sending Unit ................... Analog Instrument Panels
Fuel Injectors .................................. Engine Performance
Fuel Pump ....................................... Engine Performance
Fuel Pump Relay ................................. Engine Performance
Power Distribution
Fuse/Relay Block ................................ Power Distribution
Fusible Links ................................... Power Distribution
Generators & Regulators
Page 667 of 1333
Application Mile Service Mile Service
1983-86 2.6L 4-Cylinder
Automatic Transmission .... 7.9 (8.2) ................. 5.2
Manual Transmission ....... 6.9 (7.2) ................. 5.2
1987-90 2.6L 4-Cylinder
Automatic Transmission .... 7.9 (8.9) ................. 2.6
Manual Transmission ....... 6.9 (7.9) ................. 2.6
1989-96 3.0L V6
Automatic Transmission .... 6.1 (10.6) ................ 2.6
Manual Transmission ....... 5.1 (9.6) ................. 2.6
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
LUBRICATION SPECIFICATIONS TABLE\
\
\
\
\
\
\
Application Fluid Specifications
Brake & Clutch Fluid ........................... DOT 3 Or DOT 4
Engine Coolant ............. Ethylene-Glycol Antifreeze Coolant
Engine Oil ( 1)
Minimum Temperature
Greater Than 32
\bF (0\bC) ..... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10\bF (-23\bC) .. SAE 10W-30 Or 10W-40 API SG/CD
Maximum Temperature
Less Than 60
\bF (16\bC) ......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
\bF (-23\bC) ..... SAE 85W-90, 80W-90 API GL-5
Maximum Temperature
Less Than -30
\bF (-34\bC) ................... SAE 75W API GL-5
Power Steering Fluid ........................... Dexron-IIE ATF
Rear Axle (With Limited
Slip Differential) ........... Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic .................................... Dexron-IIE ATF
Manual Transaxle &
Transfer Case (4WD) ........... SAE 75W-85W, 75W-90 API GL-5
( 1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
FLUID CAPACITIES
FLUID CAPACITIES TABLE\
\
\
\
\
\
\
Application Quantity
A/C System R-12 Refrigerant
1983-87 .......................................... 24-26 Ozs.
1988-91 ............................................. 32 Ozs.
1992-93 ............................................. 28 Ozs.
A/C System R-134a Refrigerant ( 1)
1994-96 .......................................... 21-23 Ozs.
Automatic Transmission
1984-86 ................................. ( 2) 7.2 Qts. (6.8L)
1987-93 ..................................... 7.6 Qts. (7.2L)
1994-96 (3.0L SOHC) ......................... 7.6 Qts. (7.2L)
Page 671 of 1333
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
COOLANT (PROPYLENE-GLYCOL FORMULATIONS)
CAUTION: To avoid possible damage to vehicle use only ethylene-glycol
based coolants with a mixture ratio from 44-68% anti-freeze.
DO NOT use 100% anti-freeze as it will cause the formation
of cooling system deposits. This results in coolant
temperatures of over 300
\b F (149\bC) which can melt plastics.
100% anti-freeze has a freeze point of only -8\b F (-22\bC).
CAUTION: Propylene-Glycol Mixtures has a smaller temperature range
than Ethylene-Glycol. The temperature range (freeze-boil)
of a 50/50 Anti-Freeze/Water Mix is as follows:
Propylene-Glycol -26
\b F (-32\bC) - 257\b F (125\bC)
Ethylene-Glycol -35\b F (-37\bC) - 263\b F (128\bC)
CAUTION: Propylene-Glycol/Ethylene-Glycol Mixtures can cause the
destabilization of various corrosion inhibitors. Also
Propylene-Glycol/Ethylene-Glycol has a different specific
gravity than Ethylene-Glycol coolant, which will result in
inaccurate freeze point calculations.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by
touching a metal ground point on the vehicle prior to
servicing any ESD sensitive component.
ENGINE OIL
CAUTION: Never use non-detergent or straight mineral oil.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
WARNING: Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare
hands. Eye protection should be worn when handling or working
around halogen bulbs.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
RADIATOR FAN
Page 689 of 1333
FUEL SYSTEM PRESSURE RELEASE
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel
injection-related component. DO NOT allow fuel to contact
engine or electrical components.
1) On Colt and Mirage, remove rear seat cushion. On all
models, disconnect fuel pump harness connector at fuel tank.
2) Start engine. Let engine run until it stops. Turn ignition
off. Disconnect negative battery terminal. Connect fuel pump harness
connector.
FUEL PUMP
Removal & Installation
1) Fuel pump assembly is located inside fuel tank. Release
fuel pressure from system. See FUEL SYSTEM PRESSURE RELEASE. Raise
vehicle on hoist. Drain fuel into suitable container. Disconnect
electrical connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove nuts
securing fuel tank. Remove fuel tank from vehicle and remove fuel pump
assembly. To install, reverse removal procedure. Tighten nuts to
specification. See TORQUE SPECIFICATION table.
FUEL RAILS & INJECTORS (PFI)
Use a rag to cover fuel hose connection before disconnecting
high pressure fuel hose at fuel rail. Some residual fuel pressure may
still be in system.
Removal (Except Pickup & Ram-50 2.4L)
1) On all models, relieve fuel pressure. See
FUEL SYSTEM PRESSURE RELEASE . Disconnect negative battery cable. On
Montero, Pickup, Ram-50, Stealth and 3000GT 3.0L, disconnect air
intake plenum. On Eclipse, disconnect PCV valve hose.
2) On Colt Vista, disconnect coolant temperature sensor
connector, idle speed control servo connector and brake booster vacuum
hose. On all models, disconnect high pressure fuel hose at fuel rail.
3) Disconnect fuel return hose. Disconnect vacuum hoses. On
Eclipse, Colt and Colt 200, disconnect throttle cable clamp. Remove
center cover. On all models, disconnect injector electrical
connectors. Remove fuel rail bolts and lift fuel rail and injectors
from engine.
Installation
To install, reverse removal procedure. Tighten bolts to
specifications. See TORQUE SPECIFICATIONS table.
Removal (Pickup & Ram-50 2.4L)
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Drain coolant. On all models,
disconnect air intake hose. Disconnect breather hose (if applicable)
and vacuum hoses.
2) Disconnect coolant lines as necessary for clearance.
Disconnect injector electrical connectors. Position all lines, hoses
and electrical connectors out of way. Disconnect throttle and/or
kickdown cables. Remove throttle body assembly and position it out of
the way.
3) Disconnect high pressure fuel hose at fuel rail.
Disconnect fuel return line and vacuum line connection at fuel rail.
Remove fuel rail bolts and lift fuel rail and injectors from engine.
Page 690 of 1333
Installation
1) To install, reverse removal procedure. Injectors may be
removed after fuel rail is removed from intake manifold. Use new
insulators and "O" rings when installing injectors.
2) Use spindle oil or gasoline on "O" ring. Install injectors
into fuel rail with a twisting motion. Adjust throttle and kickdown
cable (if applicable). Do not drop injectors while removing or
installing fuel rail.
OXYGEN (O2) SENSOR
Removal & Installation
1) O2 Sensor is mounted in exhaust pipe below exhaust header.
It is equipped with a permanent pigtail which must be protected from
damage when sensor is removed. Ensure sensor is free of contaminants,
avoid using cleaning solvents of any type. Sensor may be difficult to
remove when engine temperature is less than 120
F (48 C).
2) Always use anti-seize compound on threads before
installation. On non-turbo models, remove sensor using Remover
(MD998703). On turbo models, use Remover (MD998748) on Eclipse and
Galant, or Remover (MD998770) on Stealth and 3000GT. Tighten oxygen
sensor to specification. See TORQUE SPECIFICATIONS table.
THROTTLE BODY
Removal
Disconnect air intake hose. Remove accelerator and automatic
speed control cables (if equipped). Disconnect fuel vapor hose,
electrical harness connector, vacuum hose and coolant hoses. Remove
throttle body retaining bolts.
Disassembly
Remove throttle position sensor. Remove idle speed control
motor. Remove throttle bracket and connector bracket (if equipped).
Remove idle position switch and adjusting nut.
NOTE: DO NOT remove throttle valve. DO NOT use cleaning solvents
on throttle position sensor, idle speed control motor or
idle position switch.
Cleaning
Clean all parts except those noted in solvent. Check vacuum
port and passage for clogging. Clean vacuum, vapor and fuel passages
with compressed air.
Reassembly
To reassemble, reverse disassembly procedure.
Installation
To install, reverse removal procedure.
THROTTLE POSITION SENSOR/SWITCH
Removal & Installation
Throttle position sensor/switch is located on throttle body.
Disconnect TPS electrical connector. Remove bolts holding TPS and
remove TPS. To install, reverse removal procedure. Tighten throttle
position sensor/switch to specification. See TORQUE SPECIFICATIONS
table. For adjustment procedure, see ON-VEHICLE ADJUSTMENTS article.
TURBOCHARGERS
Page 705 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual \b\
\
\
\
\
\
\
Fluid Levels](/img/19/57332/w960_57332-704.png "MITSUBISHI MONTERO 1991 Owners Manual \b\
\
\
\
\
\
\
Fluid Levels")
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
2.6L ........................................ 9.7 Qts. (9.2L)
3.0L ....................................... 10.0 Qts. (9.5L)
1994-95
3.5L ....................................... 10.0 Qts. (9.5L)
Differential
1987-88 ...................................... 1.9 Qts. (1.8L)
Page 707 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual Service Or Inspect
\
\
\
\
\
\](/img/19/57332/w960_57332-706.png "MITSUBISHI MONTERO 1991 Owners Manual Service Or Inspect
\
\
\
\
\
\")
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Valve Clearance (Jet Valve Only)
\b\
\
\
\
\
\
\
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (If Equipped)
\b\
\
\
\
\
\
\
Disc Brake Pads
\b\
\
\
\
\
\
\
Drum Brake Linings & Rear Wheel Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Fuel & Vapor Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joint
\b\
\
\
\
\
\
\
Power Steering Fluid (If Equipped)
\b\
\
\
\
\
\
\
Power Steering Hoses (If Equipped)
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Lubricate Upper Control Arm Bushings
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Engine Coolant
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Page 709 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual 37,500 MILE (60,000 KM) SERVICE \
\
\
\
\
\
\
Service](/img/19/57332/w960_57332-708.png "MITSUBISHI MONTERO 1991 Owners Manual 37,500 MILE (60,000 KM) SERVICE \
\
\
\
\
\
\
Service")
37,500 MILE (60,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Change Engine Oil
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-94 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
45,000 MILE (72,000 KM) SERVICE
45,000 MILE (72,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)