clutch MITSUBISHI MONTERO 1991 Owner's Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 82 of 1333
Fig. 7: Front Blower Switch Terminal ID (Colt Vista & Montero)
Courtesy of Mitsubishi Motor Sales of America.
DUAL PRESSURE SWITCH
Montero, Pickup & Ram-50
1) Turn engine off. Disconnect harness connector at dual
pressure switch (located near condenser). Jumper harness connector.
Turn A/C switch and blower switch to ON positions. Momentarily turn
ignition on and listen for compressor clutch engagement.
2) If compressor clutch does not engage, check evaporator
thermistor and engine coolant temperature switch. Check for a faulty
fuse. Repair or replace components as necessary. If compressor clutch
engages, go to next step.
3) Connect manifold gauge set to system, and check operating
pressures. Dual pressure switch should allow compressor operation if
system pressure is 30-384 psi (2-27 kg/cm
). If dual pressure switch
does not operate within specified pressure range, discharge system
using approved refrigerant recovery/recycling equipment, and replace
switch.
4) After replacing switch, recharge system, and monitor
pressures for proper compressor operation. If dual pressure switch
cuts power to compressor clutch while driving even though temperatures
inside have not yet decreased, high pressure side of dual pressure
switch has possibly been activated. Go to next step.
5) Discharge system using approved refrigerant
recovery/recycling equipment. Replace switch, and recharge system.
Ensure compressor clutch operates within 30-384 psi (2-27 kg/cm
).
Check for sufficient system cooling.
Page 83 of 1333
ENGINE COOLANT TEMPERATURE SWITCH
1) Turn engine off. Disconnect connector at engine coolant
temperature switch. Jumper wires on harness side of connector. If
vehicle uses a single connector, ground connector.
2) Press A/C switch to ON position and turn blower switch to
ON position. Momentarily turn ignition on and listen for compressor
clutch engagement. Clutch should engage. If clutch does not engage,
check fuse and other components wired in series with compressor
clutch.
EVAPORATOR THERMISTOR
Disconnect connector and remove thermo relay from evaporator
core. Jumper wires on harness side connector. Turn A/C switch to ON
position and turn on blower. Momentarily turn ignition on and listen
for compressor clutch engagement. If clutch does not engage, check
fuse and other components wired in series with compressor clutch.
HIGH PRESSURE SWITCH
Colt Vista
Disconnect high pressure switch connector. Jumper wires on
harness side of connector. Momentarily turn ignition on and listen for
compressor clutch engagement. If clutch does not engage, check fuse
and other components wired in series with compressor clutch.
HIGH/LOW PRESSURE CUT-OFF SWITCH
Pickup & Ram-50
1) Turn engine off. Disconnect High/Low Pressure Cut-Off
(HLPCO) switch, located on refrigerant line near condenser. Jumper
HLPCO wiring harness connector. Turn A/C switch and blower switch to
ON positions. Momentarily turn ignition on and listen for compressor
clutch engagement.
2) If compressor clutch does not engage, check evaporator
thermistor and engine coolant temperature switch. Check for a faulty
fuse. Repair or replace as necessary. If compressor clutch engages, go
to next step.
3) Connect manifold gauge set to system, and check operating
pressures. HLPCO switch should allow compressor operation if system
pressure is 28-385 psi (1.9-27 kg/cm
). If HLPCO switch does not
operate within specified pressure range, discharge system using
approved refrigerant recovery/recycling equipment, and replace switch.
4) After replacing switch, recharge system, and monitor
pressures for proper compressor function. If HLPCO switch cuts power
to compressor clutch while driving even though temperatures inside
have not yet decreased, high pressure side of new HLPCO switch has
possibly been activated. Go to next step.
5) Discharge system using approved refrigerant
recovery/recycling equipment. Replace switch, and recharge system.
Ensure compressor clutch operates within 28-385 psi (1.9-27 kg/cm
).
Check for sufficient system cooling.
LOW PRESSURE SWITCH
Colt Vista
Disconnect low pressure switch connector. Jumper wires on
harness side of connector. Momentarily turn ignition on and listen for
compressor clutch engagement. If clutch does not engage, check fuse
and other components wired in series with compressor clutch.
Page 84 of 1333
COMPRESSOR CLUTCH
Disconnect wiring to compressor clutch. Connect battery
voltage directly to A/C compressor clutch wiring harness connector
terminals. If a click is heard, clutch engagement is okay. If click is
not heard, pulley and armature are not making contact. Repair or
replace as necessary.
REAR BLOWER SWITCH
Montero
With blower switch in position indicated in REAR BLOWER
SWITCH CONTINUITY TEST table, ensure continuity exists between
terminals listed. See Fig. 8.
REAR BLOWER SWITCH CONTINUITY TEST TABLE
\
\
\
\
\
Switch Terminal
Position Numbers Continuity
OFF ................. 1-6 ................. No
Low .............. 1, 2 & 6 .............. Yes
Medium 1 ......... 1, 3 & 6 .............. Yes
Medium 2 ......... 1, 4 & 6 .............. Yes
High ............. 1, 5 & 6 .............. Yes
\
\
\
\
\
Fig. 8: Identifying Rear Blower Switch Terminals (Montero)
Courtesy of Mitsubishi Motor Sales of America.
REFRIGERANT TEMPERATURE SENSOR
Disconnect refrigerant temperature sensor electrical
connector. Using an ohmmeter, measure resistance between terminals. At
Page 94 of 1333
\003
* A /C -H EA TE R S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 991 M it s u bis h i M onte ro
GENERAL INFORMATION
A/C-Heater System Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
Motorist Assurance Program (MAP)
OVERVIEW
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Heating, Ventilation and Air Conditioning
ACCUMULATORS
ACTUATORS (ELECTRICAL)
ACTUATORS (VACUUM)
AIR CONDITIONING FITTINGS
AIR CONDITIONING HOSES
AIR CONDITIONING METAL LINES, HOSES AND FITTING ASSEMBLIES
AIR CONTROL DOORS
AIR DAMS (EXTERNAL)
AIR DISTRIBUTION SYSTEM
BELTS
BLEND DOORS
BLOWER FANS (BLOWER WHEEL OR SQUIRREL CAGE)
BLOWER MOTORS
BLOWER RESISTORS
BLOWER SWITCHES
CABIN AIR FILTERS
CIRCUIT BREAKERS
COMPRESSOR CLUTCH ASSEMBLIES
COMPRESSORS
CONDENSER AIR SEALS
CONDENSER FAN MOTORS
CONDENSERS
CONNECTORS
CONTROL CABLES
CONTROL HEADS (FUNCTION SELECTORS)
CONTROL LINKAGES
CONTROL MODULES
COOLANT
COOLING FAN BLADES
COOLING FAN CLUTCHES
COOLING FAN MOTORS
EVAPORATOR DRAIN TUBES
EVAPORATOR PRESSURE REGULATORS (EPRS)
EVAPORATORS
EXPANSION VALVES
FUNCTION SELECTORS
FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS
FUSIBLE LINKS
GASKETS
HEATER CASES
HEATER CONTROL VALVES
HEATER CORES
Page 105 of 1333
Connector missing ....... C ............ Require replacement.
Inoperative ............. A ........ (2) Require replacement.
Insulation overheated ... A ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation or out of
OEM specification.
\
\
\
\
\
\
\
BLOWER SWITCHES
See SWITCHES.
CABIN AIR FILTERS
CABIN AIR FILTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air flow obstruction .... A ............. Require cleaning or
replacement.
Maintenance intervals ... 3 ............ Suggest replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
CIRCUIT BREAKERS
See FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS .
COMPRESSOR CLUTCH ASSEMBLIES
COMPRESSOR CLUTCH ASSEMBLY INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air gap incorrect ....... B .. Require repair or replacement.
Bearing seized .......... A .. Require replacement of bearing
or assembly.
Bearing worn, affecting
performance ............ A .. Require replacement of bearing
or assembly.
Coil shows signs of
overheating ............ 1 .... Suggest replacement of coil.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted,
Page 114 of 1333
Bent .................... A ............ Require replacement.
Broken .................. A ............ Require replacement.
Cracked ................. A ............ Require replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
COOLING FAN CLUTCHES
NOTE: Some lateral movement, measured at the fan blade tip, may
be normal.
COOLING FAN CLUTCH INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bearing noisy ........... A ............ Require replacement.
Bearing worn ............ A ............ Require replacement.
Fastener loose .......... A ... Require repair or replacement
of fastener.
Inoperative ............. A ........ ( 1) Require replacement.
Leaking ................. 1 ............ Suggest replacement.
Seized .................. A ............ Require replacement.
Slips (insufficient fan
speed) ................. A ............ Require replacement.
Thermal control
incorrect .............. B .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.
\
\
\
\
\
\
\
COOLING FAN MOTORS
COOLING FAN MOTOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A .. Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted,
affecting performance .. A ........... ( 1) Require repair or
replacement.
Page 225 of 1333
CRUIS E C O NTR O L S YSTE M
1991 M it s u bis h i M onte ro
1991-92 SAFETY EQUIPMENT
Mitsubishi Cruise Control Systems
Montero
DESCRIPTION & OPERATION
The cruise control system is electronically and vacuum
controlled. System components include a control unit, actuator, vacuum
pump, cruise control switch, clutch pedal switch, cruise indicator
light, diode, inhibitor switch (A/T), stoplight switch, vehicle speed
sensor and A/T control unit.
The system has self-diagnostic capability. When
self-diagnostic mode is activated, each switch and sensor is checked
for defects. When cruise control system has been cancelled without
using a normal cancel method, a code will be set and stored in control
unit. Codes can be retrieved to help determine which circuit is
malfunctioning.
PRELIMINARY INSPECTION
Before performing TROUBLE SHOOTING steps, inspect linkage
assembly, actuator, cables and vacuum hoses. Ensure linkage and cables
move smoothly. Ensure cables do not have excessive slack or tension.
TROUBLE SHOOTING
NOTE: For further trouble shooting information, see CHECK RESULTS
& SYMPTOM CHARTS. See Figs. 11-16.
SYSTEM CANCELS OR WILL NOT RESET AFTER CANCELLATION
1) Check trouble codes, see SELF-DIAGNOSTICS under DIAGNOSIS
& TESTING. If no trouble codes are stored, ensure cruise control can
be set.
2) If cruise control can be set, system may have cancelled
because of driving on steep hills or loose wiring connection. If
cruise control still cannot be set, perform SYSTEM INPUT TESTS under
DIAGNOSIS & TESTING.
3) On 1991 models, if SYSTEM INPUT TESTS check okay, check
actuator circuit. See TEST NO. 5 under CIRCUIT TESTS (1991). On 1992
models, if SYSTEM INPUT TESTS check okay, check vacuum pump circuit.
See TEST NO. 6 under CIRCUIT TESTS (1992). On all models, if SYSTEM
INPUT TESTS do not check okay, see INPUT CODE CHART. See Fig. 9 or 10.
ADJUSTMENTS
CRUISE CONTROL CABLE
1991
1) Ensure cruise control and accelerator cables are free of
bends and folds. Remove actuator cover. Loosen lock nuts and adjusting
nuts to free cables. Adjust accelerator cable "A" to correct
dimension. See Fig. 1 or 2.
2) Tighten lock nuts. Loosen adjustment bolts on intake air
plenum. Adjust plate so that inner cable free play is .04-.08" (1-2
Page 229 of 1333
CRUISE CONTROL SWITCH FUNCTION TEST
NOTE: If vehicle speed decreases approximately 9 MPH below set
speed, set speed will be cancelled.
1) Cruise control switch is part of multifunction switch
mounted on steering column. To operate cruise control system, turn
ignition on. Turn cruise control switch to ON position. Ensure switch
indicator light comes on.
NOTE: Speed will not set beyond system limit of 90 MPH.
2) With cruise control switch in ON position, drive vehicle
between 25 and 90 MPH. Press and release SET button. Vehicle speed
should stay at set speed. Instrument cluster cruise indicator light
should come on. To increase set speed, turn control switch to RESUME
position and hold until new set speed is reached.
3) To lower set speed, press SET button and hold until new
set speed is reached. To return to set speed after cancellation, move
resume switch from ON to OFF position. Vehicle speed should return to
previous setting before cancellation. Set speed should cancel when any
of the following occurs:
* Brake pedal is pressed.
* Clutch pedal is pressed.
* Transmission is shifted to Neutral or Park.
* Cruise control main switch is turned off.
* Ignition switch is turned off.
SELF-DIAGNOSTICS
1) Self-diagnostics should be performed when cruise control
cancels without the driver using normal cancel modes. Diagnosis
connector is located on right side of fuse box. Use analog voltmeter
or Multi-Use Tester (MB991341) for code retrieval.
2) Use multi-use tester according to operating instructions
provided with tester. Connect leads of analog voltmeter between cruise
control terminal and ground terminal of self-diagnostic connector. See
Fig. 6 . Read voltmeter needle sweeps to determine trouble code.
NOTE: On 1991 models, codes No. 13, 14, 15, 16 and 17 will be
displayed whether malfunction is present or not.
3) Once trouble codes have been displayed, see SELF-
DIAGNOSTIC CODE CHART to determine appropriate CIRCUIT TEST. See
Fig. 7 or 8.
4) To clear trouble codes, either disconnect battery cable or
turn ignition on. Turn main cruise control switch and set switch to ON
position. Within one second turn resume switch to ON position.
5) Hold stoplight switch and cruise control switch in ON
position for more than 5 seconds. Verify codes are cleared.
Fig. 6: Identifying Self-Diagnostic Connector Terminals
Courtesy of Mitsubishi Motor Co.
Page 239 of 1333
Test No. 1 (Power & Ground Circuit)
1) Turn ignition on. When cruise control main switch is
turned to ON position, battery voltage should be present on terminal
No. 7 of cruise control unit connector.
2) If voltage is not present, check fuse No. 3 and replace as
necessary. If fuse is okay, check and repair harness as necessary.
Terminal No. 10 should be grounded at all times. If terminal No. 10 is
not grounded, repair harness.
Test No. 2 (Set Switch Circuits)
When set switch is turned to ON position, voltage should not
be present on terminal No. 5 of cruise control unit. When set switch
is turned to OFF position, battery voltage should be present on
terminal No. 5 of cruise control unit. If circuit does not test
correctly, replace switch as necessary or repair harness.
Test No. 3 (Resume Switch Circuit)
When resume switch is turned to ON position, voltage should
not be present on terminal No. 4 of cruise control unit. When resume
switch is turned to OFF position, battery voltage should be present on
terminal No. 4 of cruise control unit. If circuit does not test
correctly, replace switch as necessary or repair harness.
Test No. 4 (Vehicle Speed Sensor Circuit)
When vehicle moves slowly, voltage should alternate from zero
volts to 3-5 volts at terminal No. 15 of cruise control unit. If
circuit does not test correctly, replace sensor as necessary or repair
harness.
Test No. 5 (Actuator Circuit)
1) When cruise control main switch is in On position, voltage
should not be present on terminal No. 8 of cruise control unit.
2) When vehicle is accelerated using resume switch, voltage
should not be present on terminal No. 9 of cruise control unit. When
vehicle is coasting by using set switch, battery voltage should be
present on terminal No. 9.
3) When vehicle is accelerated using resume switch, battery
voltage should be present on terminal No. 20 of cruise control unit.
When vehicle is coasting by using set switch, voltage should not be
present on terminal No. 20 of cruise control unit. If circuit does not
test correctly, replace actuator as necessary or repair harness.
Test No. 6 (Stoplight Switch Circuit)
1) When brake pedal is pressed, battery voltage should be
present on terminal No. 3 of cruise control unit. If voltage is not
present, adjust or replace brake switch.
2) Battery voltage should be present at all times on terminal
No. 11 of cruise control unit. If voltage is not present, check fuse
no. 7. If fuse is okay, repair harness.
Test No. 7 (Inhibitor Switch Circuit)
1) When gear shift lever is moved to Neutral or Park
position, voltage should not be present on terminal No. 2 of cruise
control unit.
2) When gear shift lever is moved to any other position,
battery voltage should be present on terminal No. 2 of cruise control
unit. If circuit does not test correctly, replace switch as necessary
or repair harness.
Test No. 8 (Clutch Switch Circuit)
When clutch pedal is pressed, battery voltage should be
present at terminal No. 1 of cruise control unit. If circuit does not
Page 243 of 1333
Test No. 5 (Vehicle Speed Sensor Circuit)
When vehicle moves slowly, 0-2 or more volts should alternate
at terminal No. 19 of cruise control unit. If circuit does not test
correctly, replace sensor as necessary or repair harness.
Test No. 6 (Vacuum Pump Circuit)
1) When cruise system is in deceleration or release mode,
battery voltage should be present on terminals No. 26 and 13 of cruise
control unit. If circuit does not test correctly, replace vacuum pump
as necessary or repair harness.
2) When cruise system is in release mode, battery voltage
should be present on terminal No. 12 of cruise control unit. When
cruise system is in hold mode, voltage on terminals No. 12, 13 and 26
will go from battery voltage to zero volts depending on driving
conditions. If circuit does not test correctly, replace vacuum pump as
necessary or repair harness.
Test No. 7 (Stoplight Switch Circuit)
When brake pedal is pressed, battery voltage should be
present on terminal No. 15 of cruise control unit. If voltage is not
present, adjust or replace brake switch. If circuit does not test
correctly, replace switch as necessary or repair harness.
Test No. 8 (Clutch Switch Circuit)
When clutch pedal is pressed, battery voltage should be
present at terminal No. 1 of cruise control unit. If circuit does not
test correctly, replace switch as necessary or repair harness.
Test No. 9 (Inhibitor Switch Circuit)
When transmission is in Neutral position, battery voltage
should be present on terminal No. 1 of cruise control unit. If circuit
does not test correctly, replace switch as necessary or repair
harness.
Test No. 10 (Overdrive Switch Circuit)
When overdrive switch is pushed to ON position, battery
voltage should be present on terminal No. 11 of cruise control unit.
If circuit does not test correctly, replace switch as necessary or
repair harness.
Test No. 11 (Idle Switch & Throttle Position Sensor Circuit)
1) When accelerator pedal is pressed, 4.5-5.5 volts should be
present on terminal No. 4 (idle switch) of cruise control unit. When
accelerator pedal is released, voltage should not be present on
terminal No. 4 of cruise control unit.
2) When accelerator pedal is pressed to wide open throttle,
4.0-5.5 volts should be present on terminal No. 5 (throttle position
sensor) of cruise control unit. When accelerator pedal is released, .
5-.7 volts should be present on terminal No. 5 of cruise control unit.
If circuit does not test correctly, replace sensor as necessary or
repair harness.
Fig. 22: 1992 Cruise Control Unit Connector
Courtesy of Mitsubishi Motor Co.