air condition MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 698 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
Condition Code](/img/19/57333/w960_57333-697.png "MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
Condition Code")
\
\
\
\
\
\
\
Condition Code Procedure
Bracket broken .......... A .. Require repair or replacement.
Pipe bent out of
position ............... B .. Require repair or replacement.
Pipe broken ............. A .. Require repair or replacement.
Pipe cracked ............ B .. Require repair or replacement.
Pipe leaking ............ A ............ Require replacement.
Pipe missing ............ C ............ Require replacement.
Pipe plugged ............ A ............ Require replacement.
Pipe weak due to
corrosion, but no leaks
present ................ 1 ............ Suggest replacement.
Weld broken ............. A .. Require repair or replacement.
\
\
\
\
\
\
\
EXHAUST CONNECTIONS
EXHAUST CONNECTION INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
incorrect .............. B ......... Require replacement of
hardware.
Clamp broken ............ A ........... Require replacement.
Clamp loose ............. A . Require repair or replacement.
Clamp missing ........... C ........... Require replacement.
Corroded, affecting
structural integrity ... 1 ........... Suggest replacement.
Incorrect type (i.e.
flange, ball & socket
etc.) .................. B ........... Require replacement.
Leaking ................. A ................ Require repair.
Loose ................... A ................ Require repair.
\
\
\
\
\
\
\
HANGERS
HANGER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Broken .................. A ............ Require replacement.
Corroded, affecting
structural integrity ... 1 ............ Suggest replacement.
Incorrect type .......... B ............ Require replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Out of position ......... B .. Require repair or replacement.
Rubber deteriorated ..... 1 ............ Suggest replacement.
\
\
\
\
\
\
\
HEAT RISERS (MECHANICAL EFE DEVICES)
HEAT RISER (MECHANICAL EFE DEVICE) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Broken .................. A .......... Require replacement of
affected parts.
Diaphragm inoperative ... A ........ ( 1) Require replacement.
Page 699 of 1501
Leaking ................. A .. Require repair or replacement.
Noisy ................... 2 ... Suggest repair or replacement
of affected parts.
Seized .................. A ... Require repair or replacement
of affected parts.
Spring broken ........... B .......... Require replacement of
spring(s).
Spring inoperative ...... A .......... Require replacement of
spring(s).
(1) - If the inoperative diaphragm is separate from the heat
riser, then require replacement of the inoperative
diaphragm. If the inoperative diaphragm is part of the
heat riser, then replace the heat riser.
\
\
\
\
\
\
\
HEAT SHIELDS
HEAT SHIELD INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent .................... B .. Require repair or replacement.
Broken .................. A ............ Require replacement.
Corroded, affecting
structural integrity ... 1 ............ Suggest replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
MANIFOLDS (CAST AND TUBE TYPE)
MANIFOLD (CAST AND TUBE TYPE) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air injection tube in
manifold broken ........ A ... Require repair or replacement
of injection tube or
replacement of manifold.
Air injection tube in
manifold corroded,
affecting structural
integrity .............. 1 ......... Suggest replacement of
injection tube or manifold.
Air injection tube in
manifold leaking ....... A ... Require repair or replacement
of injection tube or
replacement of manifold.
Air injection tube in
manifold loose ......... A ................. Require repair.
Air injection tube in
manifold restricted .... A .......... Require replacement of
injection tube or manifold.
Air injection tube in
manifold threads
damaged ................ A ..... Require repair of injection
tube or manifold.
Air injection tube in
manifold threads stripped
(threads missing) ...... A .......... Require replacement of
injection tube or manifold.
Bolt broken ............. A ... Require replacement of bolts.
Page 700 of 1501
Bolt loose .............. A ........... Require tightening or
replacement of bolts.
Bolt missing ............ C ... Require replacement of bolts.
Corroded, affecting
sealability ............ A .. Require repair or replacement.
Cylinder head threads
stripped ............... A ... Require repair or replacement
of cylinder head.
Gasket leaking .......... A ........... Require tightening or
replacement of gasket.
Heat stove bent ......... B ........... (1) Require repair or
replacement of stove.
Heat stove broken ....... A ......... ( 1) Require replacement
of stove.
Heat stove corroded,
affecting structural
integrity .............. 1 ......... ( 1) Suggest replacement
of stove.
Heat stove missing ...... C ......... ( 1) Require replacement
of stove.
Manifold broken ......... A .. Require repair or replacement.
Manifold cracked ........ B .. Require repair or replacement.
Manifold warped ......... A .. Require repair or replacement.
Out of specification .... B .. Require repair or replacement.
Stud broken ............. A .... Require replacement of stud.
Stud missing ............ C .... Require replacement of stud.
Stud threads damaged .... A ... Require repair or replacement
of stud.
Stud threads stripped
(threads missing) ...... A .... Require replacement of stud.
( 1) - Stove may not be available separately; this may require
replacement of manifold.
\
\
\
\
\
\
\
MECHANICAL EFE DEVICES
See HEAT RISERS (MECHANICAL EFE DEVICES) .
MUFFLERS AND RESONATORS
MUFFLER AND RESONATOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Body shell distorted,
affecting performance or
structural integrity ... A ............ Require replacement.
Corrosion hole .......... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Mounting bracket broken . A .. Require repair or replacement.
Mounting bracket
cracked ................ B .. Require repair or replacement.
Nipple cracked .......... A .. Require repair or replacement.
Nipple loose ............ B ............ Require replacement.
Outer wrap peeling
(exhaust not leaking) .. 1 ............ Suggest replacement.
Plugged ................. A ............ Require replacement.
Puncture (other than a
drain hole) ............ A ............ Require replacement.
Rattling or knocking noise
from inside muffler .... B ............ Require replacement.
Seam open (exhaust
Page 702 of 1501
F - BASIC TESTING
1998 Mitsubishi Montero
1998 ENGINE PERFORMANCE
Mitsubishi - Basic Diagnostic Procedures
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
INTRODUCTION
The following diagnostic steps will help prevent overlooking
a simple problem. This is also where to begin diagnosis for a no-start
condition. The first step in diagnosing any driveability problem is
verifying the customer's complaint with a test drive under the
conditions the problem reportedly occurred.
Before entering self-diagnostics, perform a careful and
complete visual inspection. Most engine control problems result from
mechanical breakdowns, poor electrical connections or
damaged/misrouted vacuum hoses. Before condemning the computerized
system, perform each test listed in this article.
NOTE: Perform all voltage tests with a Digital Volt-Ohmmeter
(DVOM) with a minimum 10-megohm input impedance, unless
stated otherwise in test procedure.
PRELIMINARY INSPECTION & ADJUSTMENTS
VISUAL INSPECTION
Visually inspect all electrical wiring, looking for chafed,
stretched, cut or pinched wiring. Ensure electrical connectors fit
tightly and are not corroded. Ensure vacuum hoses are properly routed
and are not pinched or cut. See M - VACUUM DIAGRAMS article to verify
routing and connections (if necessary). Inspect air induction system
for possible vacuum leaks.
MECHANICAL INSPECTION
Compression
Check engine mechanical condition with a compression gauge,
vacuum gauge, or an engine analyzer. See engine analyzer manual for
specific instructions.
WARNING: DO NOT use ignition switch during compression tests on fuel
injected vehicles. Use a remote starter to crank engine.
Fuel injectors on many models are triggered by ignition
switch during cranking mode, which can create a fire hazard
or contaminate the engine's oiling system.
Check engine compression with engine at normal operating
temperature, all spark plugs removed and throttle wide open. See
COMPRESSION SPECIFICATIONS table.
COMPRESSION SPECIFICATIONS TABLE
\
\
\
\
\
\
Application (1) Specification
Compression Ratio
1.5L (VIN A) ..................................... 9.0:1
1.8L (VIN C) ..................................... 9.5:1
Page 706 of 1501
![MITSUBISHI MONTERO 1998 Service Manual of publication. \
\
\
\
\
\
MFI CONTROL RELAY
MFI control](/img/19/57333/w960_57333-705.png "MITSUBISHI MONTERO 1998 Service Manual of publication. \
\
\
\
\
\
MFI CONTROL RELAY
MFI control")
of publication. \
\
\
\
\
\
MFI CONTROL RELAY
MFI control relay switches power to vehicle sensors and
actuators including Volume Airflow (VAF) sensor, crankshaft position
sensor, idle speed control, injectors and fuel pump. When ignition
switch is turned to RUN position, PCM energizes coils controlling
injectors, VAF sensor and idle air control. When ignition switch is
turned to START position, PCM energizes coils (through park/neutral
position switch on A/T models) to supply power to fuel pump. Relay
failure will cause a no-start condition. For testing procedure, see I
- SYSTEM/COMPONENT TESTS article.
IGNITION CHECKS
* PLEASE READ THIS FIRST *
NOTE: Perform all circuit tests with a Digital Volt-Ohmmeter
(DVOM) with a minimum 10-megohm input impedance, unless
stated otherwise in test procedure.
SPARK
Check for spark at coil wire (if applicable) and at each
spark plug wire using a high output spark tester. Check spark plug
wire resistance on suspect wires. Wire resistance should not exceed
22,000 ohms for all models except Eclipse 2.0L non-turbo and Montero.
On Eclipse 2.0L non-turbo, resistance should not exceed 8000 ohms. On
Montero, resistance should not exceed 26,000 ohms.
CAMSHAFT POSITION (CMP) SENSOR
For CMP sensor testing procedure, see G - TESTS W/CODES
article.
CRANKSHAFT POSITION (CKP) SENSOR
For CKP sensor testing procedure, see G - TESTS W/CODES
article.
DISTRIBUTORLESS IGNITION SYSTEM (DIS - 4-CYLINDER)
Ignition Coil Resistance (Eclipse)
1) On Mirage 1.8L, see POWER TRANSISTOR (MIRAGE). On Eclipse\
2.0L non-turbo, go to step 3). On Eclipse 2.0L turbo and 2.4L,
disconnect ignition coil connector. Go to next step.
2) On Eclipse 2.0L turbo, use DVOM to measure primary coil
resistance between ignition coil connector terminals No. 2 and 3 (coil
for cylinders No. 1 and 4) and terminals No. 1 and 3 (coil for
cylinders No. 2 and 3). See Fig. 3. On Eclipse 2.4L, use DVOM to
measure primary coil resistance Between ignition coil terminals. Go to
step 4).
Fig. 2: Ignition Coil Connector Terminals (Eclipse 2.0L Non-Turbo)
Courtesy of Mitsubishi Motor Sales of America
Page 718 of 1501
G - TESTS W/CODES
1998 Mitsubishi Montero
1998 ENGINE PERFORMANCE
Mitsubishi - Self-Diagnostics
Montero & 3000GT
INTRODUCTION
* PLEASE READ THIS FIRST *
NOTE: If no faults were found while performing basic diagnostic
procedures in F - BASIC TESTING article, proceed with
self-diagnostics in this article. If no Diagnostic Trouble
Codes (DTCs) or only pass codes are present after entering
self-diagnostics, proceed to H - TESTS W/O CODES article for
diagnosis by symptom (i.e., ROUGH IDLE, NO START, etc.).
SYSTEM DIAGNOSIS
NOTE: PCM diagnostic memory is retained by direct power supply
from battery. Memory is not erased by turning off ignition,
but it will be erased if battery or PCM is disconnected.
System diagnosis can be accomplished using a scan tool. See
ENTERING ON-BOARD DIAGNOSTICS . Powertrain Control Module (PCM)
monitors several different engine control system circuits. If an
abnormal input signal occurs, a Diagnostic Trouble Code (DTC) is
stored in PCM memory and assigned a DTC number. Each circuit has its
own DTC number and message. A specific DTC indicates a particular
system failure, but does not indicate that cause of failure is
necessarily within system.
A DTC does not condemn any specific component; it simply
points out a probable malfunctioning area. If a DTC is set, PCM will
turn on MIL. System failures encountered are identified as either hard
failures or intermittent failures as determined by PCM.
Hard Failures
Hard failures cause MIL to come on and remain on until
failure is repaired. If MIL comes on and remains on (MIL may flash)
during vehicle operation, cause of failure may be determined by using
appropriate DTC diagnostic procedure. See TROUBLE CODE DEFINITION. If
a sensor fails, PCM will use a substitute value in its calculations to
continue engine operation. In this condition (limp-in mode), vehicle
is functional, but loss of good driveability may result.
Intermittent Failures
Intermittent failures may cause MIL to flicker, or come on
and go out after intermittent DTC goes away. However, corresponding
DTC will be retained in PCM memory. If related DTC does not reoccur
within a certain time frame, related DTC will be erased from PCM
memory. Intermittent failures may be caused by a sensor, connector or
wiring problems. See INTERMITTENTS in H - TESTS W/O CODES article.
The PCM also records and stores engine operating conditions
when malfunction occurred. This information is referred to as freeze
frame data. If malfunction is an engine misfire, or fuel system rich
or fuel system lean condition, freeze frame data will be updated with
the most current information regarding these failures. Freeze frame
data recorded is:
* Fuel System Status
Page 745 of 1501
PCM or performing resistance tests.
NOTE: Perform all resistance and voltage tests using a Digital
Volt-Ohmmeter (DVOM) with a minimum 10-megohm impedance,
unless stated otherwise in test procedures.
Using scan tool, display and record Diagnostic Trouble DTCs
(DTCs). See ENTERING ON-BOARD DIAGNOSTICS under SELF-DIAGNOSTIC
SYSTEM. If scan tool is blank, see SCAN TOOL WILL NOT COMMUNICATE. If
no DTCs are displayed, see H - TESTS W/O CODES article.
Clear DTCs. See CLEARING DTCS under SELF-DIAGNOSTIC SYSTEM.
Road test vehicle (if necessary) and attempt to duplicate conditions
that caused original complaint. Recheck for DTCs. If no DTCs are
displayed, go to INTERMITTENT DTCS. If one or more DTCs are displayed,
repair DTCs in order, starting with lowest numbered DTC. Clear DTCs
after each repair. Recheck for DTCs to confirm repair.
SCAN TOOL WILL NOT COMMUNICATE
NOTE: For terminal identification, see TERMINAL IDENTIFICATION. For
circuit and wire color identification, see
L - WIRING DIAGRAMS article.
1) Using DVOM, check voltage between Data Link Connector
(DLC) terminal No. 16 and chassis ground. If battery voltage does not
exist, check and repair junction connectors and wiring harness between
DLC and power supply.
2) If battery voltage exists, check for continuity between
DLC terminal No. 4 and chassis ground, and between DLC terminal No. 5
and chassis ground. If continuity does not exist, check and repair
wiring harness between DLC and chassis ground. If continuity exists,
go to next step.
3) Try a different scan tool adapter cable. If scan tool does
not communicate, try scan tool on a known-good vehicle. If scan tool
still does not communicate, replace scan tool.
INTERMITTENT DTCS
This procedure applies if you have been sent here from
diagnostic tests and have just attempted to simulate the condition
that initially set DTC. The following additional checks may assist in
identifying a possible intermittent problem:
* Visually inspect related wiring harness connectors for
broken, bent, pushed out or corroded terminals.
* Visually inspect related wiring harness for chafed, pierced
or partially broken wires.
* Check all pertinent technical service bulletins.
DTC P0100: VOLUME AIRFLOW (VAF) SENSOR CIRCUIT FAILURE
NOTE: For terminal identification, see TERMINAL IDENTIFICATION. For
circuit and wire color identification, see
L - WIRING DIAGRAMS article.
NOTE: Procedures are provided by manufacturer for component
testing using an engine analyzer with oscilloscope
capability. Refer to manufacturer's operation manual for
instructions in use of oscilloscope.
1) If using scan tool, go to step 3). Disconnect VAF sensor
connector. Install Test Harness (MB991348) between VAF sensor and
connector. Using engine analyzer with oscilloscope capability, connect
Page 746 of 1501
special patterns probe to VAF sensor connector terminal No. 3 or to
PCM connector terminal No. 61.
2) Start engine. Verify waveform high frequency and low
frequency patterns are of about the same length (time). Verify
wavelength decreases and frequency increases as engine RPM increases.
If conditions are not as specified, replace VAF sensor. If conditions
are as specified, go to step 4).
3) Warm vehicle to normal operating temperature. Ensure
headlights and accessories are off. Using scan tool, read VAF sensor
frequency value (item 12). See VOLUME AIRFLOW SENSOR VALUES table.
Frequency should increase when engine is raced. If values are not as
specified, replace VAF sensor. If values are as specified, turn
ignition switch to off position and disconnect VAF sensor connector.
Go to next step.
VOLUME AIRFLOW SENSOR VALUES TABLE
\
\
\
\
\
\
Application Hz @ 700 RPM Hz @ 2500 RPM
Montero ................. 25-51 ................. 80-120
3000GT
DOHC
Non-Turbo ........... 24-50 ................. 71-111
Turbo ............... 26-52 ................. 93-133
SOHC .................. 21-47 .................. 57-97
\
\
\
\
\
\
4) On 3000GT, go to next step. On Montero, disconnect MFI
relay connector. Using DVOM, check for continuity between VAF sensor
connector terminal No. 4 and MFI relay connector terminal No. 1. If
continuity does not exist, repair wiring harness as necessary. If
continuity exists, go to next step.
5) Using DVOM, check for continuity between chassis ground
and VAF sensor connector terminal No. 5. If continuity does not exist,
repair wiring harness as necessary. If continuity exists, go to next
step.
6) Ensure ignition switch is in OFF position. Disconnect PCM
connector. Ground PCM connector terminal No. 19. Using DVOM, check for
continuity between chassis ground and VAF sensor connector terminal
No. 7. If continuity does not exist, repair wiring harness as
necessary. If continuity exists, go to next step.
7) On 3000GT, go to next step. On Montero, ground PCM
connector terminal No. 61. Using DVOM, check for continuity between
chassis ground and VAF sensor connector terminal No. 3. If continuity
does not exist, repair wiring harness as necessary. If continuity
exists, turn ignition switch to ON position and go to step 9).
8) Turn ignition switch to ON position. Using DVOM, check
voltage between chassis ground and VAF sensor connector terminal No.
4. If battery voltage does not exist, repair wiring harness as
necessary. If battery voltage exists, go to next step.
9) Using DVOM, check voltage between chassis ground and VAF
sensor connector terminal No. 3. If voltage is not 4.8-5.2 volts,
replace PCM. If voltage is as specified, condition required to set DTC
is not present at this time. Go to next step.
10) Test is complete. Intermittent problem may exist. Road
test vehicle (if necessary) and attempt to duplicate conditions that
caused original complaint. Recheck for DTCs. If no DTCs are displayed,
go to INTERMITTENT DTCS .
DTC P0105: BAROMETRIC (BARO) PRESSURE SENSOR CIRCUIT FAILURE
NOTE: BARO pressure sensor is built into Volume Airflow (VAF)
sensor. For DTC P0105 test purposes, VAF sensor will be
Page 747 of 1501
referred to as BARO pressure sensor. For terminal
identification, see VAF sensor under TERMINAL IDENTIFICATION.
For circuit and wire color identification, see
L - WIRING DIAGRAMS article.
1) Component testing procedure without using scan tool not
available from manufacturer at time of publication. Turn ignition
switch to ON position. Using scan tool, read BARO sensor pressure
(item 25). See BARO PRESSURE SENSOR SPECIFICATIONS table. If pressure
is not as specified, replace BARO pressure sensor. If pressure is as
specified, go to next step.
BARO PRESSURE SENSOR SPECIFICATIONS TABLE
\
\
\
\
\
\
Altitude in Ft. (M) Pressure in kPa (mmHg)
0 (0) .......................................... 101 (768)
1969 (600) ...................................... 95 (710)
3937 (1200) ..................................... 88 (660)
5906 (1800) ..................................... 81 (610)
\
\
\
\
\
\
2) Disconnect BARO pressure sensor connector. Using DVOM,
check for continuity between chassis ground and BARO pressure sensor
connector terminal No. 5. If continuity does not exist, repair wiring
harness as necessary. If continuity exists, go to next step.
3) Turn ignition switch to OFF position. With BARO pressure
sensor disconnected, disconnect PCM connector. Ground PCM connector
terminal No. 51. Using DVOM, check for continuity between chassis
ground and BARO pressure sensor connector terminal No. 2. If
continuity does not exist, repair wiring harness as necessary. If
continuity exists on Montero, go to next step. On 3000GT, go to step
5).
4) Ground PCM connector terminal No. 42. Check for continuity
between chassis ground and BARO pressure sensor connector terminal No.
1. If continuity does not exist, repair wiring harness as necessary.
If continuity exists, go to next step.
5) Reconnect PCM connector. With BARO pressure sensor
connector disconnected, turn ignition switch to ON position. Using
DVOM, check for voltage between chassis ground and BARO pressure
sensor connector terminal No. 1. If voltage is not 4.8-5.2 volts,
replace PCM. If voltage is as specified, condition required to set DTC
is not present at this time. Go to next step.
6) Test is complete. Intermittent problem may exist. Road
test vehicle (if necessary) and attempt to duplicate conditions that
caused original complaint. Recheck for DTCs. If no DTCs are displayed,
go to INTERMITTENT DTCS .
DTC P0110: INTAKE AIR TEMPERATURE (IAT) SENSOR CIRCUIT
FAILURE
NOTE: IAT sensor is built into Volume Airflow (VAF) sensor. For
DTC P0110 test purposes, VAF sensor will be referred to as
IAT sensor. For terminal identification, see VAF sensor
under TERMINAL IDENTIFICATION . For circuit and wire color
identification, see L - WIRING DIAGRAMS article.
1) If using scan tool, go to step 3). Disconnect IAT sensor
connector. Using a thermometer, check engine compartment ambient
temperature. Using DVOM, check resistance between IAT sensor terminals
No. 5 and 6. Resistance should be 6000 ohms at 32
F (0C), 2700 ohms
at 68F (20C) or 400 ohms at 176F (80C). If resistance is not as
specified, replace IAT sensor. If resistance is as specified, go to
Page 749 of 1501
wiring harness as necessary. If continuity exists, go to next step.
5) Reconnect PCM connector. Turn ignition switch to ON
position. Check voltage between chassis ground and ECT sensor
connector terminal No. 1. If voltage is not 4.5-4.9 volts, replace
PCM. If voltage is as specified, condition required to set DTC is not
present at this time. Go to next step.
6) Test is complete. Intermittent problem may exist. Road
test vehicle (if necessary) and attempt to duplicate conditions that
caused original complaint. Recheck for DTCs. If no DTCs are displayed,
go to INTERMITTENT DTCS .
DTC P0120: THROTTLE POSITION (TP) SENSOR CIRCUIT FAILURE
NOTE: For terminal identification, see TERMINAL IDENTIFICATION. For
circuit and wire color identification, see
L - WIRING DIAGRAMS article.
1) If using scan tool, go to step 3). Disconnect TP sensor
connector. Using DVOM, check resistance between TP sensor terminals
No. 1 and No. 4. If resistance is not 3500-6500 ohms, replace TP
sensor. If resistance is as specified, go to next step.
2) Check resistance between TP sensor terminals No. 1 and 3
on Montero or No. 2 and 4 on 3000GT. While monitoring DVOM, slowly
open throttle from idle to fully open position. If resistance does not
change smoothly, replace TP sensor. If resistance changes smoothly, go
to step 4).
3) Turn ignition switch to ON position. Using scan tool, read
TP sensor voltage value (item 14). With throttle at idle, value should\
read 300-1000 mV. Value should increase while slowly opening throttle.
At wide open throttle, value should read 4500-5500 mV. If value is not
as specified, replace TP sensor. If value is as specified, go to next
step.
4) Disconnect TP sensor connector. Using DVOM, check
continuity between chassis ground and TP sensor connector terminal No.
1. If continuity does not exist, repair wiring harness as necessary.
If continuity exists on 3000GT, go to next step. On Montero, go to
step 6).
5) Check continuity between chassis ground and TP sensor
connector terminal No. 4. If continuity does not exist, repair wiring
harness as necessary. If continuity exists, go to next step.
6) Turn ignition switch to OFF position. Disconnect PCM
connector. Ground specified PCM connector terminal. See
TP SENSOR-TO-PCM WIRING HARNESS TERMINAL IDENTIFICATION table. Check
for continuity between chassis ground and specified TP sensor
connector terminal. If continuity does not exist, repair wiring
harness as necessary. If continuity exists on 3000GT, go to step 8).
On Montero, go to next step.
TP SENSOR-TO-PCM WIRING HARNESS TERMINAL IDENTIFICATION TABLE
\
\
\
\
\
\
Application TP Sensor Terminal No. PCM Terminal No.
Montero ................. 3 ......................... 78
4 ......................... 42
3000GT .................. 2 ......................... 78
\
\
\
\
\
\
7) Reconnect PCM connector. Turn ignition switch to ON
position. Check voltage between chassis ground and TP sensor connector
terminal No. 4 on Montero or No. 1 on 3000GT. If voltage is not 4.8-5.
2 volts, replace PCM. If voltage is as specified, condition required
to set DTC is not present at this time. Go to next step.
8) Test is complete. Intermittent problem may exist. Road