window MITSUBISHI MONTERO 1998 Workshop Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 1041 of 1501
Fig. 14: Power Window System Wiring Diagram (Mirage - 4-Door)
Page 1042 of 1501
Fig. 15: Power Window System Wiring Diagram (Montero)
Page 1043 of 1501
Fig. 16: Power Window System Wiring Diagram (Montero Sport)
Page 1044 of 1501
Fig. 17: Power Window System Wiring Diagram (3000GT)
Page 1218 of 1501
COMPONENT TESTS
DRIVE MOTOR
Eclipse & Montero Sport
Remove drive motor. See DRIVE MOTOR R & I under REMOVAL &
INSTALLATION. Using 12-volt power supply, apply voltage to 2-terminal
connector. Reverse power supply leads to reverse motor direction.
Replace motor as necessary.
Galant
Remove drive motor. See DRIVE MOTOR R & I under REMOVAL &
INSTALLATION. Using 12-volt power supply, apply voltage to terminals
No. 1 (Blue wire) and No. 4 (Blue/White wire) of 6-terminal drive
motor connector. Reverse power supply leads to reverse motor
direction. Replace motor as necessary.
Montero
Remove drive motor. See DRIVE MOTOR R & I under REMOVAL &
INSTALLATION. Using 12-volt power supply, apply voltage to terminals
No. 1 (Green wire) and No. 3 (Green/Red wire and Black wire) of 4-
terminal drive motor connector. Reverse power supply leads to reverse
motor direction. Replace motor as necessary.
3000GT
Remove drive motor. See DRIVE MOTOR R & I under REMOVAL &
INSTALLATION. Using 12-volt power supply, apply voltage to terminals
No. 1 (Red/Blue wire) and No. 2 (Red/Yellow wire) of 8-terminal driv\
e
motor connector. Reverse power supply leads to reverse motor
direction. Replace motor as necessary.
DRIVE MOTOR LIMIT SWITCH
Eclipse & Montero Sport
1) Remove sun roof ECU. Look into viewing windows while
turning rotating wheel. See Fig. 2. Turn rotating wheel until White
marks appear. When White marks appear in viewing windows at same time,
stop turning rotating wheel.
2) Close sun roof fully. Install timed sun roof control unit.
Ensure wiring connector is properly inserted into control unit. Insert
a flat-blade screwdriver, place on tab and press to right, being
careful not to pinch wiring. See Fig. 3.
Fig. 2: Timing Sun Roof ECU (Eclipse & Montero Sport)
Courtesy of Mitsubishi Motor Sales of America
Page 1342 of 1501
Power Top/Sunroof Circuits
POWER WINDOWS
Page 1343 of 1501
Power Window Circuit
STARTING/CHARGING
Page 1477 of 1501
WIPER/WASHER SYSTEM
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Wiper/Washer Systems
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
DESCRIPTION & OPERATION
All models are equipped with a 2-speed wiper motor with an
optional intermittent wiper feature. Some models are equipped with a
rear wiper/washer.
Galant is equipped with a wiper system that varies
intermittent setting speed with vehicle speed. System uses ignition
switch, wiper switch, intermittent switch, washer switch, vehicle
speed sensor, and Electronic Time Alarm Control System (ETACS) ECU.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE \
\
\
\
\
\
Component Location
Assist-ECU (Diamante) ............. Above Right Kick Panel
ETACS-ECU ....................... Behind Left Side Of Dash
Wiper Relay
Front
Except Diamante &
3000GT ....................... Integral With Steering
Column Switch
Rear
Eclipse .............. Within Rear Wiper/Washer Switch
Montero &
Montero Sport ................ On Relay Block, Behind
Left Side Of Dash
3000GT ................ Behind Left Rear Quarter Panel
\
\
\
\
\
\
ADJUSTMENTS
FRONT WIPER ARM ADJUSTMENT
Ensure wiper motor is in park position. Position wiper arm
and blade assembly so tip of blade is specified distance above front
window trim. See FRONT WIPER ADJUSTMENT SPECIFICATIONS table.
FRONT WIPER ADJUSTMENT SPECIFICATIONS TABLE
\
\
\
\
\
\
Driver's Side Passenger's Side
Model In. (mm) In. (mm)
Diamante ....... 2.56-3.15 (65-80) .... .79-1.38 (20-35)
Eclipse .......... .19-.59 (5-15) .... 1.65-2.05 (42-52)
Galant ........... .39-.79 (10-20) ..... .39-.79 (10-20)
Mirage .......... .79-1.18 (20-30) .... .79-1.18 (20-30)
Montero ......... .98-1.38 (25-35) ... 1.38-1.77 (35-45)
Montero Sport ... .98-1.20 (25-31) ... 1.20-1.50 (31-38)
3000GT ........... .59-.79 (15-20) ..... .59-.79 (15-20)
\
\
\
\
\
\
Page 1478 of 1501
REAR WIPER ARM ADJUSTMENT
NOTE: Diamante, Galant and Mirage are not equipped with rear
wipers.
Ensure wiper motor is in park position. Position wiper arm
and blade assembly so tip of blade is specified distance from edge of
window. See REAR WIPER ADJUSTMENT SPECIFICATIONS table.
REAR WIPER ADJUSTMENT SPECIFICATIONS TABLE
\
\
\
\
\
\
Model In. (mm)
Eclipse .............................. 4.98-5.38 (125-135)
Montero & Montero Sport ................ 2.56-2.95 (65-75)
3000GT ............................................... ( 1)
( 1) - Position blade tip along ceramic edge of window.
\
\
\
\
\
\
COMPONENT TESTS
* PLEASE READ THIS FIRST *
NOTE: For headlight washer switch testing on Montero,
see STEERING COLUMN SWITCHES article.
WASHER MOTOR TEST (FRONT & REAR)
1) Ensure washer reservoir fluid is at proper level. Turn
ignition switch to ON position. Press washer button on wiper/washer
switch. If fluid does not spray on windshield, turn ignition off.
Check for plugged washer hoses from washer reservoir to windshield
nozzle. Repair as necessary.
2) If washer hoses are not plugged, disconnect washer motor
electrical connector. Check for poor connection or connector damage.
Repair as necessary. If connector is okay, connect battery power to
washer motor terminals. Washer motor should operate. Replace motor as
necessary.
FRONT WIPER MOTOR TEST
Checking Wiper Motor Operation
Disconnect wiring connector from wiper motor. Connect battery
voltage to wiper motor connector as shown, and ensure wiper motor
operates at low and high speeds. See Fig. 1 or 2. Replace motor as
necessary.
Checking Automatic Stop
1) Operate wiper motor at low speed. See Fig. 1 or 2.
Disconnect battery voltage during operation to stop motor.
2) Using a jumper wire, connect terminals as shown. See
Fig. 1 or 2. Connect 12 volts to indicated terminal, and ground wiper
motor bracket. Ensure wiper arm is correctly parked. Replace motor as
necessary.