check engine MITSUBISHI MONTERO 2000 Service Repair Manual

GDI -Troubleshooting 13A-201
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
41Injector
drive time*1D
Engine: CrankingWhen engine coolant
temperature is 0_
C120 - 160 msCode No.
4113A-147
When engine coolant
temperature is 20_
C70 - 90 ms
When engine coolant
temperature is 80_
C20 - 35 ms
Injector
drive time*2D
Engine coolant
temperature: 85 -
95_
CIdling0.3 - 0.8 ms
95_
C
D
Lamps and all
accessories: OFF
D
Transmission:
2,500 r/min0.4 - 1.0 ms
D
Transmission:
P range
D
Within six minutes
after engine start-
ing
When engine is sud-
denly racedIncreases
44Ignition ad-
vance valueD
Engine: After hav-
ing warmed up
D
Timing lamp is set.
(The timing lamp is
set in order toIdling12 - 28_
BTDCCode No.
4413A-148
set in order to
check actual igni-
tion timing.)
D
Within six minutes
after engine start-
ing
2,500 r/min15 - 35_
BTDC
49A/C relayEngine: After having
warmed up, idlingA/C switch: OFFOFF (compressor
clutch is not oper-
ating)Procedure
No.3113A-194
A/C switch: ONON (compressor
clutch is operat-
ing)
67Stop lamp
switchIgnition switch: ONBrake pedal: De-
pressedOFFProcedure
No.3213A-195
Brake pedal: Re-
leasedON
68EGR valveD
Engine coolant
temperature: 85 -
95_
CIdling2 - 20 STEPProcedure
No.3513A-196
D
Lamps and all
accessories: OFF
D
Transmission: P
range
2,500 r/min0 - 10 STEP
74Fuel pres-
sure sensorD
Engine coolant
temperature: 85 -
95_
CEngine: Cranking2 MPa or moreCode No.
5613A-151
D
Lamps and all
accessories: OFF
D
Transmission: P
range
Engine: Idling4.0 - 6.9 MPa


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-203
ACTUATOR TEST REFERENCE TABLE
Item
No.Inspection
itemDrive ContentsInspection contentsNormal condi-
tionInspec-
tion pro-
cedure
No.Reference
page
01InjectorCut fuel to the
No.1 injector.Engine:
Idling after warming-upIdling condition
becomes differ-Code
No. 4113A-147
02Cut fuel to the
No.2 injector.
(Cut the fuel supply to each
injector in turn and check
cylinders which does notent (becomes
unstable, or the
engine stalls).
03Cut fuel to the
No.3 injector.affect idling.)
04Cut fuel to the
No.4 injector.
05Cut fuel to the
No.5 injector.
06Cut fuel to the
No.6 injector.
07Fuel pump
(low-pres-
sure)Operates the
fuel pump (low-
pressure) to cir-
culate fuel.Ignition
switch:
ONPinch the return
hose with fin-
gers to feel the
pulse of the fuel
being circulated.Pulse is felt.Proce-
dure
No.2913A-193
Operating
sound can be
heard around
the fuel tank.Sound of opera-
tion can be
heard
08Purge con-
trol solenoid
valveSolenoid valve
turns from OFF
to ON.Ignition switch: ONSound of opera-
tion can be
heard when so-
lenoid valve is
driven.Proce-
dure
No.3613A-197
17Basic ignition
timingSolenoid valve
turns from OFF
to ON.DEngine: Idling
DSet a timing light.
5_BTDC--
21Condenser
fanDrive the fan
motorDIgnition switch: ON
DA/C switch: ON
Fan motor runsProce-
dure
No.2113A-187
34Electronic-
controlled
throttle valve
systemStop the throttle
control servoIgnition switch: ONThe throttle
valve opens
slightlyCode
No. 9113A-161


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-205
Terminal
No.Normal condition Check condition (Engine condition) Check item
18Condenser fan relayCondenser fan not operatingSystem voltage
Condenser fan operating0 - 3 V or more
19Air flow sensor resetEngine: Idling0-1V
signal
Engine speed: 3,000 r/min6-9V
20A/C relayDEngine: Idling
DA/C switch: OFF to ON (Compressor operating)System voltage or
changes momentarily 6
V or more to 0 - 3 V
21Fuel pump relayIgnition switch: ONSystem voltage
Engine: Idling0-3V
22Engine warning lampIgnition switch: OFF to ONSystem voltage
23GDI ECO indication
lampIgnition switch: OFF to ON0 - 3 V (system voltage
after five seconds)
Rev the engine suddenly.System voltage
34Purge control solenoidDEngine coolantEngine: stoppedSystem voltage
valvetemperature: 80 -
95_C
DIgnition switch:
ON
Engine: After starting, in-
crease the engine speed
up to 3,500 r/minThe voltage drops
41Power supplyIgnition switch: ONSystem voltage
47
43Engine ignition signalEngine speed: 3,000 r/min0.3 - 3.0 V
44Engine coolant tem-
perature sensorIgnition switch: ONWhen engine coolant tem-
perature is 0_C3.2 - 3.8 V
When engine coolant tem-
perature is 20_C2.3 - 2.9 V
When engine coolant tem-
perature is 40_C1.3 - 1.9 V
When engine coolant tem-
perature is 80_C0.3 - 0.9 V
45Crank angle sensorEngine: Cranking0.4 - 4.0 V
Engine: Idling1.5 - 2.5 V
46Power supply voltage
applied to accelerator
pedal position sensor
(1st channel)Ignition switch: ON4.5 - 5.5 V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-206
Terminal
No.Normal condition Check condition (Engine condition) Check item
49Engine control relayIgnition switch: OFF0-3V
Ignition switch: ONSystem voltage
51EGR valve (A)Ignition switch: OFF to ON5-8V
53EGR valve (C)
(Repeatedly changes
for approx. 3 seconds)
60EGR valve (B)
62EGR valve (C)
52Power steering fluid
pressure switchEngine: Idling after
warming-upWhen steering wheel is
stationarySystem voltage
When steering wheel is
turned0-3V
55Barometric pressureIgnition switch: ONAt an altitude of 0 m3.7 - 4.3 V
sensor
At an altitude of 1,200 m3.2 - 3.8 V
56Camshaft position sen-Engine: Cranking0.4 - 3.0 V
sor
Engine: Idling0.5 - 2.0 V
58Ignition switch-STEngine: Cranking8 V or more
61A/C switch 2Refer to GROUP 55 - Troubleshooting (Check at A/C-ECU or Engine-ECU
Terminal).
63Injector open circuit
check signalEngine: Increases from idling up to 4,000 r/minThe voltage decreases
slightly (approx. 0.7 V)
from 4.5 - 5.0 V.
64Intake air temperature
sensorIgnition switch: ONWhen intake air tempera-
ture is 0_C3.2 - 3.8 V
When intake air tempera-
ture is 20_C2.3 - 2.9 V
When intake air tempera-
ture is 40_C1.5 - 2.1 V
When intake air tempera-
ture is 80_C0.4 - 1.0 V
65Air flow sensorEngine: Idling2.2 - 3.2 V
Engine speed: 2,500 r/min
66Backup power supplyIgnition switch: OFFSystem voltage
71Oxygen sensorEngine: Running at 2,500 r/min after warming-up
(Check by using a digital voltmeter.)Voltages of 0 V and 0.8
V alternate


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-207
Terminal
No.Normal condition Check condition (Engine condition) Check item
78Throttle position sen-
sor (2nd channel)Ignition switch: ONRelease the accelerator
pedal.4.0 V or higher
Depress the accelerator
pedal fully.0.4 - 0.6 V
79Accelerator pedal posi-
tion switchIgnition switch: ONRelease the accelerator
pedal.0-1V
Depress the accelerator
pedal slightly.4 V or more
80Vehicle speed sensorDIgnition switch: ON
DMove the vehicle slowly forwardVoltages of 0 and 8 - 12
V alternate (changes
repeatedly)
83A/C switch 1Engine: IdlingA/C switch: OFF0-3V
A/C switch: ON (Com-
pressor is operating)System voltage
86Small lamp switchLighting switch: OFF0-3V
Lighting switch: Tail light positionSystem voltage
87Sensor applied voltageIgnition switch: ON4.5 - 5.5 V
93Fuel pressure sensorEngine: Idling0.3 - 4.7 V
95Accelerator pedal posi-
tion sensor (1st chan-Ignition switch: ONRelease the accelerator
pedal.0.985 - 1.085 V
nel)
Depress the accelerator
pedal fully.4.0 V or higher
98Ignition switch-IGIgnition switch: ONSystem voltage
123Stop lamp switchDepress the brake pedal.System voltage
Release the brake pedal.0-3V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-208
CHECK CHART FOR RESISTANCE AND CONTINUITY
BETWEEN TERMINALS
1. Turn the ignition switch to OFF.
2. Disconnect the engine-A/T-ECU connector.
3. Measure the resistance and check for continuity between
the terminals of the engine-A/T-ECU harness-side
connector while referring to the check chart.
NOTE
(1) When measuring resistance and checking continuity,
a harness for checking contact pin pressure should
be used instead of inserting a test probe.
(2) Checking need not be carried out in the order given
in the chart.
Caution
If the terminals that should be checked are mistaken,
or if connector terminals are not correctly shorted
to earth, damage may be caused to the vehicle wiring,
sensors, engine-A/T-ECU and/or ohmmeter.
Be careful to prevent this!
4. If the ohmmeter shows any deviation from the standard
value, check the corresponding sensor, actuator and
related electrical wiring, and then repair or replace.
5. After repair or replacement, recheck with the ohmmeter
to confirm that the repair or replacement has corrected
the problem.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Fuel Pump (High Pressure)13A-241
"
CA
O-RING/FUEL PRESSURE HOSE INSTALLATION
1. Apply a small amount of fresh engine oil to the O-ring.
Caution
Take care not to let any of the engine oil get inside
the fuel pump (high pressure) or the delivery pipe
assembly.
2. While being careful not to damage the O-ring, turn the
fuel pressure hose to the left and right and connect it
to the delivery pipe assembly. After connecting, check
that the fuel injector turns smoothly.
3. If the fuel pressure hose does not turn smoothly, the cause
may be that the O-ring is getting caught. Remove the fuel
pressure hose, check the O-ring for damage and
re-connect the fuel pressure hose to the delivery pipe
assembly and then re-check.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

15
DRIVE CYCLE
Performing the running test of the car using the following five drive cycle patterns makes it possible to
monitor all the diagnosis codes that are required for operation of the car in order to determine if the
applicable system is operating properly or not.
In other words, doing such a drive allows to regenerate any kind of trouble which involves illuminating the
Engine Warning Lamp (Check Engine Lamp) and to verify the repair procedure has eliminated the trouble
[the Engine Warning Lamp (Check Engine Lamp) is no longer illuminated].
Caution
Two technicians should always be in the vehicle when carrying out a test drive.
NOTE
Check that the diagnosis code is not output before traveling in the Drive cycle pattern. Erase the diagnosis
code if it has been output.
DRIVE CYCLE PATTERN LIST
PROCEDURE MONITOR ITEM DIAGNOSIS CODE
Catalytic converter monitor P04201
Heated oxygen sensor monitor P0130
2 Fuel trim monitor P0170
3 Feed back monitor P0125
4 Other monitor P0136, P0201, P0202, P0203, P0204, P0205,
P0206, P0300, P0301, P0302, P0303, P0304,
P0305, P0306, P0325
NOTE
The vehicle speed sensor (P0500) and the power steering fluid pressure switch (P0551) are used to
determine if the system is operating properly or not through use of the Data List function of the MUT-II.
2001 PAJERO/MONTERO WAGON Workshop Manual 6G74
GDI - Troubleshooting

www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -General/General Information/Troubleshooting13A-3
GENERAL
OUTLINE OF CHANGES
Due to the changes as shown below, the service procedures regarding the different description from
the previous version have been established.
DOn M/T, the engine-ECU has been changed as diagnosis code P1603 has been added.
DOn A/T, the engine-A/T-ECU has been changed as an on-board diagnosis system has been adopted.
The engine warning lamp control, the diagnosis function, the service data output and the actuator
test are basically the same as for M/T.
DOn A/T, an dual oxygen sensor has been adopted. This sensor is the same as for the previous
M/T.
GENERAL INFORMATION
GENERAL SPECIFICATIONS
ItemsSpecifications
Engine-ECU Identification No.E2T79277
E2T79278
Engine-A/T-ECU Identification No.E2T76292
E2T76293
TROUBLESHOOTING
DIAGNOSIS FUNCTION
ENGINE WARNING LAMP (CHECK ENGINE LAMP)
The following item has been added as diagnosis code P1603 has been added. The other items are
the same as before.
Engine warning lamp inspection items
Code No.Diagnosis item
P1603Battery backup line malfunction
INSPECTION CHART FOR DIAGNOSIS CODES
Diagnosis code P1603 has been added. The other codes are the same as for the previous M/T.
Code No.Diagnosis itemReference page
P1603Battery backup line malfunction13A-4


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -TroubleshootingGDI -Troubleshooting13A-4
INSPECTION PROCEDURE CLASSIFIED BY DIAGNOSIS CODE
Code No. P1603 Battery backup line malfunctionProbable cause
Range of Check
DStarting sequence was completed.
DThe battery voltage is 10 V or more.
Set Condition
DBattery backup line voltage is less than 2 V.DOpen or short circuit in the battery back-up line or
loose connector contact
DMalfunction of engine-ECU
DMalfunction of engine-A/T-ECU
NOTE: If the engine is started while the ignition-off
current draw connector has been pulled off, the
engine - ECU or the engine-A/T-ECU
judges that the battery backup line is open, and
illuminates the engine warning lamp and stores this
diagnosis code.
NG
Replace the engine-ECU or engine-A/T-ECU .
Check the trouble symptoms.
OKNG
Repair
Check the harness wire between the battery and the engine-ECU
or engine-A/T-ECU, and repair if necessary.
OKNG
Repair
Check the harness wire between the battery and the engine-ECU
or engine-A/T-ECU , and repair if necessary.
OK
NG
Repair
MUT-IISelf-Diag Code
Is code No. P1603 set?
Check the following connector:D-117 , D-120 OKNO
Check the following connectors:E-13, D-27, D-31 drive vehicles>, D-223 YESMeasure at engine-ECU connector D-117 or engine-A/T-ECU
connector D-120 .
DDisconnect the connector, and measure at the harness
side.
DThe voltage between terminal No.60 or 66
and earth
OK:System voltageNG
Intermittent malfunction (Refer to GROUP 00 - Points to Notes
for Intermittent Malfunction).


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk