ignition MITSUBISHI MONTERO 2000 Service Repair Manual

AUTOMATIC TRANSMISSION -Troublehshooting II>23-75
Code No. 22, 23 Front propeller shaft speed sensor
systemProbable cause
Code No. 22 is output to indicate anopencircuit or short-circuit in the front
propeller shaft speed sensor if no signal is input from the front propeller shaft
speed sensor when shifting from 2WD to 4WD while driving atmedium to low
speeds.
Code No. 23 is output to indicate anopencircuit or short-circuit in the front
propeller shaft speed sensor if the signal input from the front propeller shaft
speed sensor is unstable when the freewheelengageswitch is on.DMalfunction of front propeller shaft speed sensor
DMalfunction of harness or connector
DMalfunction of transfer-ECU
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
OK NG
OK
OK
To the nextpage
NG
OK
NG
NG
Repair
Replace the transfer-ECU.
OKMUT-
IIData List
DNo. 2 Front propeller shaft speed sensor
OK:Refer to P.23-87 (Data List Chart).
OK
OK
NG
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminals 18 and earth
OK:0.5 V or less
NG
Repair
Replace the transfer-ECU.
NG
Check the trouble symptoms.
Check the trouble symptoms.
Replace the transfer-ECU.
OK
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DDisconnect front propeller shaft speed sensor connector
C-17.
DIgnition switch: ON
DVoltage between terminals 7 and earth
OK:4.8 - 5.2 V
Measure the front propeller shaft speed sensor output wave
pattern at transfer-ECU connector E-105 (using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 3rd
DVoltage between terminals 7 - 18
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope tern B>) should be output, and the maximum value
should be 4.8 V or more and the minimumvalue
should be 0.8 V or less.
There should be no noise in the output wave pattern.
NG
RepairCheck the following connectors:C-17, E-105NG
NG
Repair
Check the following connector:E-105Repair
NG
Check the harness between the front propeller shaft speed
sensor and the transfer-ECU.
Check the following connector:C-17
Check the trouble symptoms.
Check the following connector:E-105


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-76
(2)NG
(3)NG
From the previouspage
(1)NG
OK
NG
Measure at front propeller shaft speed sensor connector C-17.
DDisconnect the connector and measure at the harness
side.
(1) Resistance between terminal 1 and earth
OK:2
Wor less
(2) Voltage between terminal 2 and earth
(Ignition switch: ON)
OK:4.8 - 5.2 V
(3) Voltage between terminal 3 and earth
(Ignition switch: ON)
OK:System voltage
Check the harness between the front propeller shaft speed
sensor and the ignition switch, and repair if necessary.
Check the following connectors:D-208, D-213, D-32, E-115
NG
Check the trouble symptoms.
Check the harness between the front propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Earth
line)
Replace the front propeller shaft speed sensorOK
OK
Repair
Check the harness between the front propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Sensor
line)
Eliminate the cause of the noise.
NG
Check the trouble symptoms.
NG
Repair
OK
NG
Repair
OK
DCheck the harness between the front propeller shaft speed
sensor and the transfer-ECU.
DCheck the harness between the front propeller shaft speed
sensor and the ignition switch.
Check the following connectors:D-208, D-213, D-32, E-115,
E-105


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-77
Code No. 24, 25 Rear propeller shaft speed sensor systemProbable cause
Code No. 24 is output to indicate anopencircuit or short-circuit in the rear
propeller shaft speed sensor if the signal input from the rear propeller shaft
speed sensor is unstable when the APS voltage is 1.5 V or higher.
Code No. 25 is output to indicate anopencircuit or short-circuit in the rear
propeller shaft speed sensor if the signal input from the rear propeller shaft
speed sensor is unstable when the freewheelengageswitch is on.DNo. 3 Rear propeller shaft speed sensor
DMalfunction of harness or connector
DMalfunction of transfer-ECU
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
OK NG
Check the following connector:E-105
OK
OK
To the nextpage
NG
OK
NG
NG
Repair
Check the following connector:C-08
Replace the transfer-ECU.
OKMUT-
IIData List
DNo. 3 Rear propeller shaft speed sensor
OK:Refer to P.23-87 (Data List Chart).
OK
OK
NG
Check the trouble symptoms.
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminals 18 and earth
OK:0.5 V or less
NG
Repair
Replace the transfer-ECU.
NG
Check the trouble symptoms.
Check the trouble symptoms.
Replace the transfer-ECU.
OK
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DDisconnect rear propeller shaft speed sensor connector
C-08.
DIgnition switch: ON
DVoltage between terminals 9 and earth
OK:4.8 - 5.2 V
Measure the rear propeller shaft speed sensor output wave
pattern at transfer-ECU connector E-105 (using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 3rd
DVoltage between terminals 9 - 18
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope) should be
output, and the maximum value should be 4.8 V or
more and the minimumvalue should be 0.8 V or
less.
There should be no noise in the output wave pattern.
NG
RepairCheck the following connectors:C-08, E-108NG
NG
Repair
Check the following connector:E-108Repair
NG
Check the harness between the rear propeller shaft speed
sensor and the transfer-ECU.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-78
(2)NG
(3)NG
From the previouspage
(1)NG
OK
NG
Measure at rear propeller shaft speed sensor connector C-08.
DDisconnect the connector and measure at the harness
side.
(1) Resistance between terminal 1 and earth
OK:2
Wor less
(2) Voltage between terminal 2 and earth
(Ignition switch: ON)
OK:4.8 - 5.2 V
(3) Voltage between terminal 3 and earth
(Ignition switch: ON)
OK:System voltage
Check the harness between the rear propeller shaft speed
sensor and the ignition switch, and repair if necessary.
Check the following connectors:D-208, D-213, D-32, E-115
NG
Check the trouble symptoms.
Check the harness between the rear propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Earth
line)
Replace the rear propeller shaft speed sensorOK
OK
Repair
Check the harness between the rear propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Sensor
line)
Eliminate the cause of the noise.
NG
Check the trouble symptoms.
NG
Repair
OK
NG
Repair
OK
DCheck the harness between the rear propeller shaft speed
sensor and the transfer-ECU.
DCheck the harness between the rear propeller shaft speed
sensor and the ignition switch.
Check the following connectors:D-208, D-213, D-32, E-115,
E-105


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-80
Code No. 31 Transfer lever switch systemProbable cause
Code No. 31 is output to indicate anopencircuit or short-circuit in the transfer
lever switch if the input signal from the transfer lever switch is unstable.DMalfunction of transfer lever switch
DMalfunction of harness or connector
DMalfunction of transfer-ECU
NG
NG
MUT-
IIData List
DNo. 6 Transfer lever position
OK:Refer to P.23-87 (Data List Chart).Transient malfunction
(Refer to GROUP 00 - Points to Note for Transient
Malfunctions.) OK
OK OKOKNG
DCheck the harness between the transfer lever switch and
the transfer-ECU, and repair if necessary.
DCheck the harness between the transfer lever switch and
the ignition switch, and repair if necessary.Repair
Check the harness between the transfer lever switch and the
ignition switch, and repair if necessary.
OK OK
NG
OK
OK
NG
NG
Check the trouble symptoms.Replace the transfer-ECU.
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DIgnition switch: ON
(1) Transfer lever position: 2H> Voltage between terminal 20
and earth
(2) Transfer lever position: 4H> Voltage between terminal 21
and earth
(3) Transfer lever position: 4H> Voltage between terminal 22
and earth
(4) Transfer lever position: 4H> Voltage between terminal 23
and earth
OK:System voltage
Measure at transfer lever switch connector E-19.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DVoltage between terminal (1) and earth
OK:System voltageNG
Replace
NG
Repair
Transfer lever switch check (Refer to P.23-117.)
Check the following connector:E-19
Repair NG
Check the following connector:E-105Repair
Check the following connectors:D-208, D-213, D-32, E-115,
E-105
Check the following connectors:D-208, D-213, D-32, E-115


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-81
Code No. 32, 33 Transfer position switch systemProbable cause
Code No. 32 is output to indicate anopencircuit or short-circuit in a transfer
position switch, a malfunction of the shift actuator or a malfunction of the
transfer shift mechanism when transfer selection does not complete while driving.
Code No. 33 is output to indicate anopencircuit or short-circuit in a transfer
position switch if the input signal from the transfer position switch is unstable.DMalfunction of transfer position switch
DMalfunction of harness or connector
DMalfunction of transfer-ECU
DMalfunction of shift actuator
DMalfunction of transfer shift mechanism
LRefer to the Transmission Workshop Manual.
OK
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
OKNG
Check the harnesses between the transfer position switches
and the transfer-ECU, and repair if necessary.OKNG
OK
OK
NG
Replace the transfer-ECU. NG
ReplaceTransfer lever switch check (Refer to P.23-117.)
Repair NG
Repair
Check the trouble symptoms.
NG OK
Replace the shift actuator.
L
MUT-
IIData List
DNo. 7 Transfer position
OK:Refer to P.23-87 (Data List Chart).
NG
Actuator test
(Only No.32)
DNo. 2, No. 3 Shift actuator
OKRefer to P.23-89 (Actuator Test).
Measure at transfer-ECU connector E-108
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminals 43, 44, 45, 46, 47 and earth
OK:System voltage
Check the following connectors:C-06, C-07, C-14, C-15, C-16
Check the following connector:E-108


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-82
Code No. 34 Freewheel engage solenoid valve systemProbable cause
Code No. 34 is output to indicate anopencircuit or short-circuit in the freewheel
engage solenoidvalve when the transfer-ECU terminal voltages are not the
same while current isbeing supplied to the freewheel engage solenoidvalve.DMalfunction of freewheel engage solenoidvalve
DMalfunction of harness or connector
DMalfunction of transfer-ECU
NG
NG
MUT-
IIActuator Test
DNo. 1 Freewheel engage solenoidvalve
OK:The solenoid valve operates for 5 seconds.Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.) OK
OK OK OKNG
DCheck the harness between the freewheelengage solenoid
valve and the transfer-ECU, and repair if necessary.
DCheck the harness between the freewheelengage solenoid
valve and the ignition switch, and repair if necessary.Repair
Check the harness between the freewheelengage solenoid
valve and the ignition switch, and repair if necessary.
OK OK
OK
NG
Check the trouble symptoms.Replace the transfer-ECU.
Measure at transfer-ECU connector E-108
DMeasure at ECU terminals.
DTransfer: 4WD
DIgnition switch: ON
DVoltage between terminals 41 and earth
OK:System voltage
Measure at freewheel engage solenoidvalve connectors A-40
and A-41.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DVoltage between terminal 1 and earth
OK:System voltageNG
Replace
NG
Repair
Freewheel engage solenoidvalve check
(Refer to GROUP 26 - On-Vehicle Service.)
Check the following connectors:A-40, A-41
Repair NG
Check the following connector:E-108
NG
Repair
OK
Check the following connectors: D-208,
D-210, D-27, A-15, A-16, A-04, E-113, E-108,
D-208, D-210, D-27, A-15, A-16, D-143, E-113, E-108,
Check the following connectors:D-208, D-210, D-27, A-15


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-83
Code No. 35 Freewheel engage switch systemProbable cause
Code No. 35 is output to indicate anopencircuit or short-circuit in the freewheel
engageswitch when the freewheelengageswitch condition does not correspond
to the fact that current isbeing supplied to the freewheel engage solenoidvalve.DMalfunction of freewheel engageswitch
DMalfunction of harness or connector
DMalfunction of transfer-ECU
NG
(1)NG
MUT-
IIData List
DNo. 38 Freewheel engageswitch
OK:Refer to P.23-87 (Data List Chart).Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.) OK
OK OK OKNG
Repair
Check the following connector:B-40
Check the harness between the freewheelengageswitch and
earth, and repair if necessary.
OK
OK
Check the trouble symptoms.Replace the transfer-ECU.
Measure at freewheel engageswitch connector B-54.
DDisconnect the connector and measure at the harness
side.
(1) Resistance between terminal 1 and earth
OK:2
Wor less
(2) Voltage between terminal 2 and earth
(Ignition switch: ON)
OK:System voltageNG
Replace
NG
Repair
Freewheel engageswitch check (Refer to GROUP 26 -
Freewheel Clutch.)
Check the following connector:B-54
MUT-
IISelf-Diag Code
DIs code No. 34 output?Code No. 34 Freewheelengage solenoidvalve system check
(Refer to P.23-82.) YES
NO
NG
(2)NG
NG
OK
Repair
Check the following connectors:E-108, E-113, B-40
Check the harness between the freewheelengageswitch and
the transfer-ECU, and repair if necessary.
Check the following connector:B-54Repair
NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting II>23-87
DATA LIST REFERENCE TABLE
Item
No.Check itemInspection conditionsNormal condition
1Accelerator pedalEngine: StoppedAccelerator pedal: Fully closed985 - 1,085 mV
position sensor
(APS)Selector lever position:
PAccelerator pedal: DepressedGradually increases from
the above value.
Accelerator pedal: Fully open4000 mV or higher
2Front propeller shaft
speed sensorTransfer position: 4WDDriving at a constant speed of
30 km/h30 km/h
3Rear propeller shaftTransfer position: 4WDDriving at a constant speed of30 km/h3Rear propeller shaft
speed sensorTransfer position: 4WDDriving at a constant speed of
30 km/h30 km/h
4Difference between
front and rear pro-
peller shaft speedsTransfer position: 4WDDriving at a constant speed of
30 km/hWithin 5 km/h
5Vehicle speedIdling in 1st (Vehicle stopped)0 km/h
Driving at a constant speed of 50 km/h in 3rd50 km/h
6Transfer lever posi-Ignition switch: ONTransfer shift lever position: 2H2H
tionEngine: StoppedTransfer shift lever position: 4H4H
Transfer shift lever position:
4HLc4HLc
Transfer shift lever position:
4LLc4LLc
7Transfer positionDriving at a constant
speed of 10 km/hTransfer shift lever position:
2H®4H2H - 4H®4H
Transfer shift lever position:
4H®4HLc4H - 4HL®4HL
Engine: Stopped
Selector lever position:Transfer shift lever position:
4HLc®4LLc4HL - 4LL®4LL
NTransfer shift lever position:
4LLc®4HLc4HL - 4LL®4HL
Driving at a constant
speed of 10 km/hTransfer shift lever position:
4HLc®4H4H - 4HL®4H
Transfer shift lever position:
4H®2H2H - 4H®2H
8Main relay voltageIgnition switch: ONSystem voltage (V)
9Ignition voltageIgnition switch: ONSystem voltage (V)
10Shift actuator cur-
rentDuring transfer selection (while motor is running)0A®0.2 A®0A
11Target currentDuring transfer selection (while motor is running)0A®1.5 A®0A
12Shift actuator volt-
ageIgnition switch: ON
Selector lever position: N
Transfer shift lever position: 2H®4H (or 4H®4HLc,
4HLc®4LLc)System voltage (V)
Ignition switch: ON
Selector lever position: N
Transfer shift lever position: 4LLc®4HLc (or 4HLc®4H,
4H®2H)System voltage (V)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting II>23-88
Item
No.Normal condition Inspection conditions Check item
21Ignition switchIgnition switch: ONON
Ignition switch: OFFOFF
22Transmission identi-
ficationVehicles with A/TA/T
23Stop lamp switchIgnition switch: ONBrake pedal: DepressedON
Engine: StoppedBrake pedal: ReleasedOFF
24Transfer leverTransfer shift lever position: 2HON
switch 2HTransfer shift lever position: Other than the aboveOFF
25Transfer leverTransfer shift lever position: 4HON
switch 4HTransfer shift lever position: Other than the aboveOFF
26Transfer leverTransfer shift lever position: 4HLcON
switch 4HLcTransfer shift lever position: Other than the aboveOFF
27Transfer leverTransfer shift lever position: 4LLcON
switch 4LLcTransfer shift lever position: Other than the aboveOFF
28Engine identificationPetrol vehiclesPETROL
Diesel vehiclesDIESEL
30Freewheel engageDuring 2WDON
solenoid valveDuring 4WDOFF
31Inhibitor switch NSelector lever position: NON
Selector lever position: Other than the aboveOFF
32Inhibitor switch PSelector lever position: PON
Selector lever position: Other than the aboveOFF
332WD switchDriving conditions: 2WD (2H)ON
Driving conditions: Other than the aboveOFF
342WD/4WD switchDriving conditions: 2WD (2H), 4WD (4H)ON
Driving conditions: Other than the aboveOFF
354H switchDriving conditions: 4WD (4H), 4WD (4HLc)ON
Driving conditions: Other than the aboveOFF
36Center differentialDriving conditions: 4WD (4HLc), 4WD (4LLc)ON
lock switchDriving conditions: Other than the aboveOFF
374LLc switchDriving conditions: 4WD (4LLc)ON
Driving conditions: Other than the aboveOFF
38Freewheel engageDuring 2WDOFF
switchDuring 4WDON


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk