ECU MITSUBISHI MONTERO 2000 Service Repair Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2000, Model line: MONTERO, Model: MITSUBISHI MONTERO 2000Pages: 1839, PDF Size: 29.19 MB
Page 1585 of 1839
CHASSIS ELECTRICAL-Ignition Switch and Immobilizer <4D56>54A-15
INSPECTION PROCEDURES FOR EACH DIAGNOSIS CODE
Code No. 11 Problem related to communication with the
ignition keyProbable cause
When the ignition switch is at the ON position, the encrypted codes
are not transmitted from the ignition key to the immobilizer-ECU.D
Malfunction of ignition key
D
Malfunction of immobilizer-ECU
D
Malfunction of harness or connector
YES
NOCan otherkeys which havebeen registered beused to start
the engine?
If code No. 12 is
output
Check the diagnosis codes.To inspection procedure 12 classified by diagnosis code
(Refer to P.54A-15.)
Check the following connectors:D-133, D-201
Register the ignition key.
If code No. 11 is
output
OK
NG
Check the trouble symptoms.
Check the harness between the immobilizer-ECU and the
ignition key ring antenna.NG
OKNG
Check the trouble symptoms.
Replace the immobilizer-ECU.NGRepair
Repair
Replace the ignition key which cannot start the engine.
Code No. 12 Ignition key is not registered, or encrypted
code from ignition key does not match.Probable cause
The ignition key has not been registered with the immobilizer-ECU.D
The ignition key has not been registered
with the immobilizer-ECU.
D
Malfunction of immobilizer-ECU
OK
NG
Replace the immobilizer-ECU.
Check the trouble symptoms.Register the encrypted code.
INSPECTION PROCEDURES FOR EACH TROUBLE SYMPTOM
Trouble SymptomInspection
procedure
No.Reference page
Communication with MUT-IIis not possible.–GROUP 13B,
13C - Trouble-
shooting
The ignition keys cannot be registered using the MUT-II.154A-16
The engine does not start. (The engine cranks but does not fire.)254A-17
Immobilizer-ECU power supply and earth circuit system check354A-18
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1586 of 1839
CHASSIS ELECTRICAL-Ignition Switch and Immobilizer <4D56>54A-16
INSPECTION PROCEDURES FOR EACH TROUBLE SYMPTOM
Inspection procedure 1
The ignition keys cannot be registered using the MUT-II.
Probable cause
The ignition key has not been registered with the immobilizer-ECU.
Or that there is a problem with the immobilizer-ECU.D
Malfunction of ignition key
D
Malfunction of harness or connector
D
Malfunction of immobilizer-ECU
OK
Check the trouble symptoms.
NG
Register the ignition key.
YES
NO YESIs a normal diagnosis code output?
NOCan none of the ignitionkeys beregistered?Replace the ignition key that cannot be registered.
To Chart Classified by Diagnosis Codes (Refer to P.54A-14.)
OKImmobilizer-ECU power supply and earth circuit system check
(Refer to Inspection Procedure 3.)
NG
Replace the immobilizer-ECU.
Check the trouble symptoms.
OK
Check the trouble symptoms.
NG
Repair
Check the harness between the immobilizer-ECU and the
diagnosis connector.
Repair
Check the following connectors:D-133, D-33, D-222, D-28
NG
NG
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1587 of 1839
CHASSIS ELECTRICAL-Ignition Switch and Immobilizer <4D56>54A-17
Inspection procedure 2
The engine does not start.
(The engine cranks but does not fire.)
Probable cause
If the fuel injection does not operate, the cause is probably a problem
with the immobilizer-ECU, or it could also be a problem with the
diesel fuel system. If an attempt has been made to start the engine
with a key that has not been properly registered, the above symptom
is a sign of normal operation.D
Malfunction of diesel fuel system
D
Malfunction of immobilizer-ECU
NGBattery check (P.54A-4)
YES
NOTo Chart Classified by Diagnosis Codes (Refer to P.54A-14.)Is a normal diagnosis code output from the immobilizer-ECU?
OK
Voltage check during cranking
OK:8V or higher
NG
Immobilizer-ECU power supply and earth circuit system check
(Refer to Inspection Procedure 4.)
Check the trouble symptoms.
NG
To inspection procedures if the enginedoes not fire
(Refer to GROUP 13B, 13C - Troubleshooting.)
OK
Check the trouble symptoms.
NG
OK
NG
Replace the immobilizer-ECU.
Check the trouble symptoms.
OK
Check the trouble symptoms.
NG
Repair
Check the harness between the immobilizer-ECU and the fuel
cut valve controller.
Repair
Check the following connectors:D-133, D-13, B-03
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1591 of 1839
CHASSIS ELECTRICAL-Ignition Switch and Immobilizer <4D56>54A-21
ENCRYPTED CODE REGISTRATION METHOD
AND RESETTING THE CODE TO THE
FACTORY SETTING
Register the encrypted code in the immobilizer-ECU and then
reset the code to the factory setting after parts have been
replaced.
Replacement partEncrypted
code
Ignition keyNecessary
Ignition key ring antenna and immobilizer-ECUNecessary
Engine-ECU*Necessary
NOTE
* : If the engine-ECU is replaced, the ignition key ring antenna
and immobilizer-ECU and ignition key should be replaced
together with it.
Each engine-ECU has an individual information for
immobilizer-ECU, and the individual information is registered
in the immobilizer-ECU.
ENCRYPTED CODE REGISTRATION METHOD
If using an ignition key that has just been newly purchased,
or if the immobilizer-ECU has been replaced, you will need
to register the encrypted codes for each ignition key being
used into the immobilizer-ECU. (A maximum of eight different
encrypted codes can be registered.)
Moreover, when the immobilizer-ECU has been replaced, you
will need to use the MUT-II
to register the password that
the user specifies into the immobilizer-ECU. (Refer to the
MUT-II
instruction manual for instructions on using the MUT-II
.)
Caution
Because registering of the encrypted codes is carried
out after all previously-registered codes have been
erased, you should have ready all of the ignition keys
that have already been registered.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1596 of 1839
CHASSIS ELECTRICAL-Combination Meter54A-26
Inspection procedure 2
Tachometer does not operate.(Other meters and gauges
operate.)
Probable cause
The cause is probably that the ignition signal is not being input from
the engine, or that there is a malfunction of the meter power supply
or earth circuit.D
Malfunction of tachometer
D
Malfunction of harness or connector
D
Malfunction of printed circuit board
OK
NG
Replace the combination meter case.
OK
Check the trouble symptoms.
NO
MUT-
IISelf-Diag Code
Is MPI, GDI or DIESEL diagnosis code No. 44 output?YESCode No. 44 Ignition coil and power transistor unit system
(Refer to GROUP 13A - Troubleshooting.)
NG
Replace the tachometer.
NG
NG
Repair RepairCheck the harness between the combination meter and the
engine-ECU.
OK:Continuity
Check the trouble symptoms.
Check the following connectors:
<6G74-A/T>D-01, D-33, E-13, B-04, D-120,
<6G74-M/T>D-01, D-33, E-13, B-04, D-117,
<4M41>D-01, D-33, E-13, D-112,
<4D56>D-01, D-33, E-13, B-07, B-07-1
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1599 of 1839
CHASSIS ELECTRICAL-Combination Meter54A-29
Inspection procedure 5
None of the meters and gauges operate.
Probable cause
If the indicators and warning lamps are normal, then the harness
from the power supply (IG1) to the combination meter is normal.D
Malfunction of printed circuit board
D
Malfunction of harness or connector
NGRepair NG
OK
Check the trouble symptoms.Repair
OK
Check the harness between the combination meter and body
earth.
Check the following connectors:D-27, D-233, D-218, D-01,
D-03
NG
Check the harness between fusible link No. 2 and the
combination meter.
Replace the combination meter case.
Inspection procedure 6
Vehicle speed sensor check
The vehicle speed sensor is used by the speedometer, engine-ECU and A/T-ECU.
NG
Check the harness between the vehicle speed sensor and
body earth, and repair if necessary.
RepairNG
OK
Check the trouble symptoms.NG
Check the harness between the vehicle speed sensor and
multipurpose fuse No. 13, and repair if necessary.
RepairNG
OK
Check the trouble symptoms.
Check the following connectors:D-213, E-115, C-09
(3)NG
(2)NG
Check the following connectors:C-09
NG
Check the harness between the vehicle speed sensor and the
combination meter, and repair if necessary.
RepairNG
OK
Check the trouble symptoms.
OK
Measure at vehicle speed sensor connector C-09.
DDisconnect the connector and measure at the harness
side.
(1) Voltage between terminal 3 and earth
OK:4.5 V or higher
(2) Continuity between terminal 2 and earth
OK:Continuity
(3) Voltage between terminal 1 and earth
OK:System voltage(1)NGCheck the following connectors:D-01, D-222, E-13, E-113,
C-09
Vehicle speed sensor check (Refer to P.54A-33.)NG
Replace
NOTE
If the trouble symptoms cannot be eliminated by the above checks, there is probably a short-circuit at
the vehicle speed sensor output side (harness, speedometer, engine-ECU or A/T-ECU), and so this should
be checked.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1624 of 1839
CHASSIS ELECTRICAL -Clock or Center Display54A-54
BEFORE REMOVING THE BATTERY
The Center display has a large amount of data unique to the vehicle in its memory. When the battery
cable is disconnected, that memory is affected as shown in the table below. Accordingly, it is necessary
to make sure that you take notes of important information before disconnecting the battery cable.
FunctionInput function/memoryWhen battery cable is disconnected
Clock set on displayCurrent timeRetains data for approx. 1 hour
Vehicle model setShort (3-door models)/long (5-door
models)Retains data for approx. 1 hour
Brightness set for displayPosition set on displayRetains data for approx. 1 hour
Unit set for trip computerkm or mile, L/100km or mpg or km/L
Average vehicle speed after resetRetains data for approx. 1 hour
Average vehicle speed on displayAverage vehicle speed after resetRetains data for approx. 1 hour
Average fuel consumption on displayAverage fuel consumption after resetRetains data for approx. 1 hour
Cruising range on displayCruising range, fuel economyRetains data for approx. 1 hour
Outside temperature on displayOutside temperature after the ignition
switch is turned to the OFF(LOCK)
position.Retains data for approx. 1 hour
* The outside temperature sensor
is located near the engine.
Therefore, incorrectly high
temperature may be displayed
when the battery cable is
reconnected within one hour.
DIAGNOSIS FUNCTION FOR CENTER DISPLAY
Center display has the following diagnosis function:
FunctionContents
Service functionThere are the following 4 diagnosis modes available
1. Check of vehicle informationThe vehicle, short (3-door models)/long (5-door models) set
2. Check of LCD segmentsThe LCD segments for display available to light on or not
3. Check of sensorsOutside temperature, voltage of fuel gauge unit, system voltage, fuel amount
remains, fuel economy calculated after supply of fuel
4. Check of units connected into
the center displayThe units connected on display
Voltage (%) on terminal for MUT-II
Vehicle speed signal sent by engine-ECU
Oscillating signal
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1630 of 1839
CHASSIS ELECTRICAL -Clock or Center Display54A-60
Terminal
No.Input/
OutputSignal symbolTerminal
voltage (V)Wiring harness
problemTrouble symptom caused by wiring
harness problem
Open
circuitShort
circuit
15Input/
OutputKHi: System
voltage
Lo: 0-1ExistsExistsValues on trip information screen (average
vehicle speed, fuel consumption and
cruising distance) are abnormal. Commu-
nication is impossible between the
engine-ECU and the MUT-II.
16------
17Input/
OutputM-BUSY
(AUDIO)Hi: 4-5
Lo: 0-1ExistsExistsAudio display does not appear. Panel
switch cannot be operated for audio unit.
Nighttime illumination does not appear for
audio unit.
18-SHIELD-GND----
19Input/
OutputM-BUSY
(A/C)Hi: 4-5
Lo: 0-1ExistsExistsA/C display does not appear.
Outside air temperature does not appear
20-SHIELD-GND----
21, 22------
23InputEX-TEMPExistsExistsOutside air temperature does not appear.
24InputILL+Hi: System
voltageExists-Nighttime illumination does not appear for
audio units.
Lo: 0-1
-ExistsBlown multipurpose fuse.
25InputACC (ACCSystem volt-Exists-Screen display does not appear.
power supply)age
-ExistsBlown multipurpose fuse.
26Input+BSystem volt-Exists-Screen display does not appear.
age
-ExistsBlown multipurpose fuse.
27InputVSSHi: System
voltage
Lo: 0-1ExistsExistsAbnormal outside air temperature ap-
pears.
(only diesel-powered vehicles)
28-GND (earth)-Exists-Screen display does not appear.
29, 30------
31-GND-TEMPExistsExistsOutside air temperature does not appear.
32InputILL -ExistsExistsThe display screen can not be dimmed.
33InputFUEL GAUGE-ExistsAbnormal cruising distance appears.
34, 35------
36InputIG1Hi: System
voltageExists-Communication with engine-ECU is im-
possible. Abnormal driving data values
appear.
-ExistsCommunication with engine-ECU is im-
possible. Abnormal driving data values
appear. Blown multipurpose fuse.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1633 of 1839
CHASSIS ELECTRICAL -Clock or Center Display54A-63
INSPECTION PROCEDURE 3
Abnormal vehicle speed is displayed on the service mode.
OK
NGRepair.
Measure at center display unit connec-
tor D-03.
DDisconnect the connector.
DVoltage between terminal 36 and
body earth.
OK:(Ignition switch: ON)
System voltage.
(Ignition switch: OFF)
0-1VNGCheck the wiring harness between the
center display unit and the junction
block, and repair if necessary.
NG
Check the wiring harness between the
center display unit and the engine-ECU,
and repair if necessary.
Select “Check of units connected into
the center display” on the service mode.
Does the symbol “MU” appear?YES NGDisconnect MUT-
II. Then check vehicle
wiring harnesses.Disconnect connector D-04.
Then check voltage at terminal 5 of that
connector.
DIgnition switch: ON
NG:More than 80% of system volt-
age
OK:Less than that
OK NO
OK
Check the connections between the
center display unit and the engine-ECU.OKReplace the center display unit.
Check the connector: D-04
Measure at center display unit connector D-03.
DDisconnect the connector.
DVoltage between terminal 36 and body earth.
OK:(Ignition switch: ON) System voltage.
(Ignition switch: OFF) 0 - 1 VNGCheck the wiring harness between the center display unit and
the junction block, and repair if necessary.
OK
Measure at center display unit connector D-03 .
DDisconnect the connector.
DVoltage between terminal 27 and body earth.
OK:HI: System voltage.
Lo: 0 - 1VNGCheck the wiring harness between the center display unit and
the vehicle speed sensor, and repair if necessary.
OK
Replace the center display unit.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1636 of 1839
CHASSIS ELECTRICAL -Clock or Center Display54A-66
INSPECTION PROCEDURE 7
Air conditioning display is not available.
Measure at center display unit connec-
tor D-03.
DDisconnect the connector.
DVoltage between terminal 36 and
body earth.
OK:System voltage (Ignition
switch: ON)
0 - 1 V (Ignition switch:
OFF)NGCheck the wiring harness between the
center display unit and the junction
block, and repair if necessary.
OK
NO OK
Check theaudio unit.
NG
NG
Repair wiring harness.
OK
OK
Replace the center display unit.
YES
Replace the A/C-ECU.
YES
Refer to GROUP 55 - A/C troubleshoot-
ing.Check the reoccurrence of symptom.OKEND
NG
Replace the center display unit.
Measure at center display unit connec-
tor D-04.
DDisconnect the connector.
DVoltage between terminal 9 and
body earth.
DVoltage between terminal 10 and
body earth.
DVoltage between terminal 19 and
body earth.
OK:Hi:4–5V
Lo:0–1V
Check the the wiring harnesses:
DBetween the center display and
A/C-ECU D-04, D-49
DBetween the center display and
AUDIO D-04, D-49
Check the reoccurrence of symptom.Select “Check of units connected into
the center display” on the service mode.
Does the symbol “AU” appear?
MUT-
IISelf-Diag code
Is the diagnosis code for A/C set?NG
NO
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk