MOTOR MITSUBISHI MONTERO 2000 Service Manual PDF

HEATER, AIR CONDITIONER AND VENTILATION -Troubleshooting 55B-15
Inspection procedure 10
The condenser fan does not operate .
Probable cause
If the condenser fan does not operate, the condenser fan relay or motor may be
defective.DMalfunction of the condenser fan relay
DMalfunction of harness or connector
DMalfunction of the engine-A/T-ECU or
engine-ECU
NG
Check the harness wire between the condenser fan relay and
the ignition switch (IG2), and repair if necessary.
NG
Repair
NG
Check the harness wire between the condenser fan motor and
body earth, and repair if necessary.
NG
Repair
NG
Repair
OK
Replace the engine-A/T-ECU or engine-ECU
.
NG
Check the harness wire between the condenser fan relay and
fusible link (1), and repair if necessary.
NG
Repair
NG
Check the harness wires between the condenser fan relay
and the condenser fan motor, between the condenser fan
relay and the engine-A/T-ECU or the
engine-ECU.NG
Repair
OK
Check the trouble symptoms.
OK
Check the following connectors:A-10X, A-27,A-04 drive vehicles>, D-143, D-116,
D-119, D-110<4M41>
OK
Check the trouble symptoms.
OK
Measure at condenser fan motor connector A-27.
DDisconnect the connector and measure at the harness
side.
DContinuity between terminal 2 and body earth
OK:ContinuityNGCheck the following connector:A-27
OK
Check the trouble symptoms.
Check the following connector:A-10X
(2) NG
OK
Check the trouble symptoms.
OK
Measure at condenser fan relay connector A-10X.
DDisconnect the connector, and measure at the J/B side.
DIgnition switch: ON
(1) Voltage between terminal 3 and body earth
OK:System voltage
(2) Voltage between terminal 5 and body earth
OK:System voltage(1) NGCheck the following connectors:A-10X, A-15, D-27, D-210,
D-208
OK
Check the condenser fan motor
(Refer to GROUP 55A - Condenser Fan).NG
Replace
Check the condenser fan relay
(Refer to GROUP 55A - On-vehicle Service).NG
Replace


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

HEATER, AIR CONDITIONER AND VENTILATION -Troubleshooting 55B-16
Inspection procedure 11
The condenser fan does not operate <4D56>.
Probable cause
If the condenser fan does not operate, the condenser fan relay or motor may be
defective.DMalfunction of the condenser fan relay
DMalfunction of harness or connector
DMalfunction of the engine-A/T-ECU or
engine-ECU
NG
Check the harness wire between the condenser fan relay and
the ignition switch (IG2), and repair if necessary.
NG
Repair
NG
Check the harness wire between the condenser fan motor and
body earth, and repair if necessary.
NG
Repair
NG
Repair
OK
NG
Check the harness wire between the condenser fan relay and
fusible link (1), and repair if necessary.
NG
Repair
NG
Check the harness wires between the condenser fan relay
and the condenser fan motor and between the condenser fan
relay and theengine coolant temperaturesensor, and repair if
necessary.
OK
Check the trouble symptoms.
OK
Check the following connectors:A-10X, A-27, A-04 drive vehicles>, D-143, B-47
OK
Check the trouble symptoms.
OK
Measure at condenser fan motor connector A-27.
DDisconnect the connector and measure at the harness
side.
DContinuity between terminal 2 and body earth
OK:ContinuityNGCheck the following connector:A-27
OK
Check the trouble symptoms.
Check the following connector:A-10X
(2) NG
OK
Check the trouble symptoms.
OK
Measure at condenser fan relay connector A-10X.
DDisconnect the connector, and measure at the J/B side.
DIgnition switch: ON
(1) Voltage between terminal 3 and body earth
OK:System voltage
(2) Voltage between terminal 5 and body earth
OK:System voltage(1) NGCheck the following connectors:A-10X, A-15, D-27, D-210,
D-208
OK
Check the condenser fan motor
(Refer to GROUP 55A - Condenser Fan).NG
Replace
Check the condenser fan relay
(Refer to GROUP 55A - On-vehicle Service).NG
Replace
NG
ReplaceReplace the engine coolant temperaturesensor.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

HEATER, AIR CONDITIONER AND VENTILATION -Troubleshooting 55B-17
DATA LIST REFERENCE TABLE
Item No.Check itemInspection contents
11Inside air temperature sensorIgnition switch: ONInside air temperature and tempera-
ture displayed on the MUT-IIare
identical.
13Outside air temperature sen-
sorIgnition switch: ONOutside air temperature and tem-
perature displayed on the MUT-II
are identical.
15Heater water temperature
sensorIgnition switch: ONHeater core surface temperature
and temperature displayed on the
MUT-IIare identical.
21Air thermo sensorIgnition switch: ONEvaporator outlet temperature and
temperature displayed on the MUT-
IIare identical.
25Photo sensorIgnition switch: ONAmount of incident light is propor-
tional to voltage displayed on the
MUT-II.
31Potentiometer for the air mix
damperIgnition switch: ON
Damper position: MAX HOTOpening angle: Approximately
100%
Ignition switch: ON
Damper position: MAX COOLOpening angle: Approximately 0%
32Potentiometer for the air
outlet changeover damperIgnition switch: ON
Damper position: FACEOpening angle: Approximately 0%
Ignition switch: ON
Damper position:FOOTOpening angle: Approximately 60%
Ignition switch: ON
Damper position: FOOT/DEFOpening angle: Approximately 80%
Ignition switch: ON
Damper position: DEFOpening angle: Approximately
100%
ACTUATOR TEST TABLE
Item No.Check itemDrive Contents
01Blower motorStopped
02Low speed
03Medium speed
04High speed
05Electric motor for the air mix damperOpening angle: Approximately 0%
06Opening angle: Approximately 50%
07Opening angle: Approximately 100%
08Electric motor for the air outlet changeoverFACE
09damperFOOT
10DEF
11Compressor ON/OFFOFF
12ON
13Inside/outside air changeover damper motorOutside air
14Inside air


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

HEATER, AIR CONDITIONER AND VENTILATION -Troubleshooting 55B-21
Inspection procedure 2
The rear A/C outlet air temperature can not be set.
Probable cause
If the air outlet temperature can not be changed after a temperature control
switch is operated,the temperature control switch, the air thermo sensor, the
magnet valve or the air mix damper maybe defective.DMalfunction of the rear A/C switch
DMalfunction of the air thermo sensor
DMagnet valve
DMalfunction of the electric motor for the air mix
damper
DMalfunction of harness or connector
DMalfunction of the rear A/C control unit
Repair
NG
NG
Check the harness wire between the rear A/C control unit and
the rear A/C switch, and repair if necessary.
NG
RepairNG
Check the harness wire between the rear A/C control unit and
the air thermo sensor, and repair if necessary.
NG
Repair
NG
Check the harness wire between the rear A/C control unit and
the air mix damper motor, and repair if necessary.
OK
Replace the rear A/C control unit.NG
Repair
NG
Check the harness wire between the rear A/C control unit and
the magnet valve, and repair if necessary.
OK
Check the trouble symptoms.
Check the following connectors:E-23, D-123, G-26,
G-24-1, G-24-4
(6) NG
OK
Check the trouble symptoms.
Check the following connectors:E-23, D-123, G-24,
G-24-1, G-24-2(3 - 5) NG
OK
Check the trouble symptoms.
Check the following connectors:E-23, D-123, G-26,
G-24-1, G-24-3(2) NG
OK
Check the trouble symptoms.
OK
Measure at rear A/C control unit connector E-23.
DConnect the connector.
DIgnition switch: ON
(1) Voltage between terminal 3 and body earth
OK:1 V (Temperature control switch: MAX HOT),
4 V (Temperature control switch: MAX COOL)
(2) Voltage between terminal 12 and body earth
OK:2.2 V [Air thermo sensor temperature: 25
_C
(1.5 k
W)]
(3) Voltage between terminal 7 and body earth
OK:1 V (Air mix damper: MAX HOT),
4 V (Air mix damper: MAX COOL)
(4) Voltage between terminal 6 and body earth
OK:10 V (When the air mix damper flap is moving to the
MAX COOL position), 0.5 V (When the air mix
damper flap is moving to the MAX HOT position)
(5) Voltage between terminal 14 and body earth
OK:0.5 V (When the air mix damper flap is moving to
the MAX COOL position), 10 V (When the air mix
damper flap is moving to the MAX HOT position)
(6) Voltage between terminal 1 and body earth
OK:System voltage (magnetic valve: OFF), 0.5 V (mag-
netic valve: ON)(1) NGCheck the following connectors:E-23, D-123, E-119
OK
Check the magnetic valve.
(Refer to GROUP 55A - Rear Heater/Rear Cooler.)NG
Replace
OK
Check the air mix damper motor.
(Refer to GROUP 55A - Rear Heater/Rear Cooler.)NG
Replace
OK
Check the air thermo sensor.
(Refer to GROUP 55A - Rear Heater/Rear Cooler.)NG
Replace
Check the rear A/C switch (temperature control switch).
(Refer to GROUP 55A - Rear Heater/Rear Cooler.)NG
Replace


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

HEATER, AIR CONDITIONER AND VENTILATION -Troubleshooting 55B-22
Inspection procedure 3
The rear blower does not operate.
Probable cause
If no air comes out of the air vents even if the rear fan switch or the front rear
fan switch is turned on, the rear blower relay circuit may be defective.DMalfunction of the rear blower relay
DMalfunction of the blower motor
DMalfunction of the rear A/C switch
DMalfunction of harness or connector
OK
Replace the rear A/C control unit.
OK
NG
Repair
NG
Repair
NG
Check the harness wire between the rear blower relay and
the ignition switch (IG2), and repair if necessary.
NG
Repair
NG
Check the harness wire between the rear blower relay and
fusible link (2), and repair if necessary.
NG
Repair
NG
Check the harness wires between the rear blower relay and
the rear A/C switch and between the rear blower relay and
the front rear fan switch, and repair if necessary.
NG
Repair
NG
Check the harness wire between the blower motor and the
rear A/C switch and between the rear A/C switch and body
earth, and repair if necessary.
NG
Repair
OK
Check the trouble symptoms.
OK
Check the following connectors:D-214, D-123, G-22,
G-22-1
OK
Check the trouble symptoms.
OK
Measure at blower motor connector G-22-1.
DDisconnect the connector and measure at the harness
side.
DAir volume adjusting switch: 3
DContinuity between terminal 1 and body earth
OK:ContinuityNGCheck the following connectors:G-22-1, G-22, E-119
OK
Check the trouble symptoms.
Check the following connectors:D-214, D-123, E-119,
E-109, E-14
(3) NG
OK
Check the trouble symptoms.
Check the following connectors:D-214, D-27(2) NG
OK
Check the trouble symptoms.
OK
Measure at rear blower relay connector D-214.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
(1) Voltage between terminal 1 and body earth
OK:System voltage
(2) Voltage between terminal 5 and body earth
OK:System voltage
(3) Voltage between terminal 3 and body earth
OK:0 V (Rear fan switch or front rear fan switch: ON)(1) NGCheck the following connectors:D-214, D-32, D-210, D-208
OK
Check the rear A/C switch (air volume adjusting switch)
(Refer to GROUP 55A - Rear Heater/Rear Cooler).NG
Replace
OK
Check the blower motor
(Refer to GROUP 55A - Rear Heater/Rear Cooler).NG
Replace
Check the rear blower relay
(Refer to GROUP 55A - On-vehicle Service).NG
Replace
Check the harness wire between the blower motor and the
rear blower relay.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

HEATER, AIR CONDITIONER AND VENTILATION -Troubleshooting 55B-23
Inspection procedure 4
The rear blower air volume can not be changed.
Probable cause
If the air volume can not be controlled, the air volume adjusting switch or the
resistor may be defective.DMalfunction of the rear A/C switch
DMalfunction of the resistor
DMalfunction of harness or connector
NG
Repair
NG
Repair
NG
Check the harness wire between the rear A/C switch and
body earth, and repair if necessary.
NG
Check the harness wire between the rear A/C switch and the
resistor and between the resistor and the blower motor, and
repair if necessary.
OK
Check the trouble symptoms.
OK
Check the trouble symptoms.
OK
Check the following connectors:E-119, G-22, G-22-2,
G-22-1
NG
Measure at rear A/C switch connector E-119.
DDisconnect the connector and measure at the harness
side.
DContinuity between terminal 1 and body earth
OK:ContinuityNGCheck the following connectors:E-119
OK
Check the resistor (Refer to GROUP 55A - Rear Heater/Rear
Cooler).NG
Replace
Check the rear A/C switch (air volume adjusting switch)
(Refer to GROUP 55A - Rear Heater/Rear Cooler).NG
Replace
Inspection procedure 5
Air outlet vents can not be changed in proportion to the
temperature adjusting switch.
Probable cause
If the air outlet temperature can not be changed after a temperature control
switch is operated, the air outlet changeover damper may be defective.DMalfunction of the electric motor for the air outlet
changeover damper
DMalfunction of harness or connector
DMalfunction of the rear A/C control unit
Repair
NG
Repair
Check the trouble symptoms.NGReplace the rear A/C control unit.
OK
Replace the air outlet
changeover damper motor.
NG
NG
Check the harness wire between the air outlet changeover
damper motor and the ignition switch (IG2), and repair if
necessary.
NG
RepairNG
Repair
NG
Check the harness wire between the air outlet changeover
damper motor and body earth, and repair if necessary.
NG
Check the harness wire between the air outlet changeover
damper motor and the rear A/C control unit.
OK
Check the trouble symptoms.
OK
Check the following connectors:G-22-3, G-22, D-123, E-23
OK
Check the trouble symptoms.
Check the following connectors:G-22-3, G-22
(2) NG
OK
Check the trouble symptoms.
YES
Measure at air outlet changeover damper motor connector
G-22-3.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
(1) Voltage between terminal 2 and body earth
OK:System voltage
(2) Continuity between terminal 1 and body earth
OK:Continuity(1) NGCheck the following connectors:G-22-3, G-22, D-123,
D-123, D-32, D-210, D-208
Can the air temperature be adjusted by means of the
temperature adjusting switch?NORefer to Inspection Procedure 2 (Refer to P.55-19).


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk