display MITSUBISHI MONTERO 2000 Service Manual Online
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2000, Model line: MONTERO, Model: MITSUBISHI MONTERO 2000Pages: 1839, PDF Size: 29.19 MB
Page 1688 of 1839
SWS -General InformationSWS -General Information54B-2
GENERAL INFORMATION
COMMUNICATION LINE
Data lines for multiplex communication are connected between the front-ECU, ETACS-ECU, column switch
assembly, sunroof motor assembly, center display, power window main switch, and power window motors
as illustrated below.
ETACS-ECUMUT-II
Column switch
assembly
Front-ECU
Power window
main switch
Power window motor
(front-right)
Center display*1
Sunroof motor
assembly*2Power window motor
(front-left)
Power window motor
(rear-right)
Power window motor
(rear-left)
NOTE
: Uni-directional communication line
: Bi-directional communication line
*
1: Vehicles with center display
*2: Vehicles with sunroof
OPERATION
BUZZER
Light Reminder Warning Buzzer Function
When the driver’s door is opened with lighting switch
in the ON (tail lamp switch or headlamp switch)
position and ignition switch in the LOCK (OFF) or
ACC position, the buzzer will sound continuously to
remind the driver that the lamps (tail lamps or
headlamps) are ON.
This function does not work if the lighting switched
off through the headlamp automatic shutdownfunction. In addition, the ignition key reminder
warning buzzer function has a priority over this
function.
Center Display Operation Annunciation
Function
On vehicles with center display, the buzzer (peeps)
sounds when the operation switch of the audio
and navigation system is pressed.
CENTRAL DOOR LOCKING SYSTEM
Central Door Locking System Operation
When the lock switch is turned ON after the unlock
switch on the driver’s door lock actuator switch
is OFF, the ETACS-ECU gives a lock output for
0.5 second. When the unlock switch is turned ON
after the lock switch on the driver’s door lock
actuator switch is OFF, the ETACS-ECU gives an
unlock output for 0.5 second.
When the front passenger’s door key or back door
key is operated, the ETACS-ECU gives a lock or
unlock output for 0.5 second.Forgotten Key Prevention Function
If, with the key reminder switch OFF and the driver’s
door switch ON, the driver’s door lock switch is
turned ON after the door unlock switch in the front
door lock actuator is turned OFF, the ETACS-ECU
waits 0.3 second then give an unlock relay output
for 0.5 second, there by preventing the doors from
being locked. This operation prevents the ignition
key from being locked inside the vehicle. This
function takes precedence over the central door
locking control function.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1695 of 1839
SWS -Troubleshooting54B-9
Input signalBuzzer operation condition
Column switchTail lamp switchTurned the lighting switch from OFF to tail lamp
position
Headlamp switchTurn the lighting switch from tail lamp position to
headlamp position
Dimmer switchTurned from OFF to ON
Passing switch
Turn-signal lamp switch
Windshield mist wiper switch
Windshield intermittent wiper switch
Windshield low-speed wiper switch
Windshield high-speed wiper switch
Windshield intermittent wiper interval adjusting
knobRotate the windshield intermittent wiper interval
adjusting knob from FAST to SLOW when the
ignition switch is in ON position (The
ETACS-ECU sends a signal around the medium
knob position)
Windshield washer switchTurned from OFF to ON
Rear wiper switch
Rear washer switch
Headlamp washer switch
Power window
main switchAny switch
TransmitterAny switch
Sunroof switchAny switch
Center displayAny switch
DIAGNOSIS CODE CHART
Code No.Diagnosis itemReference page
11Failure concerning the ETACS-ECU54B-10
12Failure concerning the column switch or improper connecting with the ETACS-ECU54B-10
13Failure concerning the front-ECU54B-11
21Short circuit in communication line54B-12
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1696 of 1839
SWS -Troubleshooting54B-10
DIAGNOSIS CODE INSPECTION PROCEDURES
Code No.11 Failure concerning the ETACS-ECUProbable cause
The ETACS-ECU monitors its own communication data, and sends a diagnosis
code when an error takes place consecutive fifteen times in 0.6 second.
The diagnosis code will be erased when the ETACS-ECU determines that its
own communication data is sent consecutive 15 times in 0.6 second.DMalfunction of ETACS-ECU
Replace the ETACS-ECU.
Code No.12 Failure concerning the column switch or
improper connection with the ETACS-ECUProbable cause
This diagnosis code is displayed when the column switch sends a signal
regardless of the transmission request signal from the ETACS-ECU (three times
or more in one second).
The diagnosis code is erased when the column switch continues to send a
signal according to the transmission request signal from the ETACS-ECU for one
second.DMalfunction of column switch
DMalfunction of ETACS-ECU
DMalfunction of wiring harness or connector
Ye s N G
NG
Check the harness wire between col-
umn switch and fusible link (2).
NG
Repair
No
OK
OK
NG
Repair
NG
OK
Check trouble symptomsNG
NG
Replace
OK
Check trouble symptomsNGCheck the harness wire between column
switch and body earth.
NG
Replace the ETACS-ECU.
Check trouble symptoms.
NG
Replace the column switch.
Check the harness wire between col-
umn switch and ETACS-ECU.
OK
Check trouble symptoms
Check the following connectors:
D-203, D-223, D-27
Check the following connectors:
D-203, D-226
Measure at column switch connector
D-203.
DDisconnect connector and
measure at harness side.
DVoltage between terminal 1 and
body earth.
OK:System voltage
Check the following connector:
D-203
Measure at column switch connector
D-203.
DDisconnect connector and
measure at harness side.
DContinuity between terminal 4
and body earth.
OK:Continuity
Is diagnosis code No. 12 output
when the ignition switch is at the
ON position?
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1697 of 1839
SWS -Troubleshooting54B-11
Code No.13 Failure concerning the front-ECUProbable cause
This diagnosis code is displayed when the signals that the front-ECU sends to
the ETACS-ECU are errors consecutive fifteen times in 0.6 second.
The diagnosis code will be erased when the front-ECU sends normal signals to
the ETACS-ECU consecutive 15 times in 0.6 second.DMalfunction of front-ECU
DMalfunction of ETACS-ECU
DMalfunction of wiring harness or connector
OK
Is diagnosis code No. 12 output
when the ignition switch is at the
ON position?Ye sMeasure at front-ECU connector A-07X.
DDisconnect connector and
measure at harness side.
DVoltage between terminal 7 and
body earth
OK:System voltageNGCheck the following connector:
A-07X
NG
Check the harness wire between front-
ECU and fusible link (2).
No
Measure at front-ECU connector A-08X.
DDisconnect connector and
measure at harness side.
DContinuity between terminal 31
and body earth.
OK:ContinuityCheck the following connectors:
A-08X, D-27, D-31, D-226NG
Repair
OK
Replace the front-ECU.
OK
Check trouble symptoms.NGReplace the front-ECU.
NG
Check the following connector:
A-08XNG
Repair
NG
RepairOK
Check trouble symptoms.
OK
Check the trouble symptoms.NGCheck the harness wire between front-
ECU and body earth.
Check trouble symptoms.
NG
Replace the ETACS-ECU.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1698 of 1839
SWS -Troubleshooting54B-12
Code No.21 Short circuit in communication linesProbable cause
This diagnosis code is displayed when the SWS communication line voltage
reaches the LO level for 0.3 second. The diagnosis code is erased when
voltage in the ETACS-ECU data line reaches the HI level for 0.3 second, or the
ETACS-ECU receives a normal signal from other ECUs or switches. While this
code is displayed, other codes are not displayed.DMalfunction of column switch
DMalfunction of front-ECU
DMalfunction of power windowmainswitch
DMalfunction of sunroof motor assembly
DMalfunction of center display
DMalfunction of ETACS-ECU
DMalfunction of wiring harness or connector
NG
Repair
OK
Ye s
Replace the column switch.
No
Ye s
Replace the front-ECU.
No
Ye s
Replace the power windowmainswitch.
No
Ye s
Replace the center display.
No
Replace the ETACS-ECU.
No
Ye s
Replace the sunroof motor assembly.
Is diagnosis code No. 21 no longer output when center
display connector D-06 is disconnected?
Is diagnosis code No. 21 no longer output when sunroof
motor assembly connector F-06 is disconnected?
Is diagnosis code No. 21 no longer output when power
window mainswitch connector H-05 is disconnected?
Is diagnosis code No. 21 no longer output when front-ECU
connector A-08X is disconnected? (However, code No. 13 is
still output.)
Is diagnosis code No. 21 no longer output when column
switch connector D-203 is disconnected? (However, code No.
12 is still output.)
NG
Check the harness wires between column switch and ETACS-ECU,
front-ECU and ETACS-ECU, power windowmainswitch and
ETACS-ECU, sunroof motor assembly and ETACS-ECU, center
display and ETACS-ECU.NG
Repair
OK
Check trouble symptoms.
Check the following connectors:
A-08X, D-06, D-25, D-27, D-29, D-31, D-203, D-226, F-02, F-06,
H-05
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1699 of 1839
SWS -Troubleshooting54B-13
TROUBLE SYMPTOM CHART
Trouble symptomInspection
procedureReference
page
Communication with the MUT-IIis impossible.A-154B-17
BuzzerLight reminder warning buzzer function does not work
normally.B-154B-17
Center display operation annunciation function does not work
normally.B-254B-18
Central door lock-Central door locking system does not work normally.C-154B-18
ing system
Some doors does not lock or unlock.C-254B-19
Some functions of central locking system do not work.C-354B-19
Forgotten key prevention function does not work.C-454B-20
Power windowPower window does not work at all.D-154B-20
Power window main switch can not operate driver’s window.D-254B-21
Power window sub switch can not operate front passenger’s or
rear window.D-354B-22
Power window main switch can not operate front passenger’s
or rear window.D-454B-23
Power window timer function does not work normally.D-554B-23
When the glass is raised, it then lowers automatically.D-654B-24
The glass is not lowered when something is jammed in the
window.D-754B-24
When the glass is fully raised, it then lowers automatically.D-854B-24
Keyless entry sys-Keyless entry system does not operate.E-154B-24
tem
The room lamp and hazard warning lamps do not operate
through the answerback function.E-254B-25
The encrypted code cannot be registered.E-354B-25
SunroofSunroof does not work at all.F-154B-26
Sunroof timer function does not work normally.F-254B-27
Safety mechanism does not function.F-354B-27
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1701 of 1839
SWS -Troubleshooting54B-15
Trouble symptomInspection
procedureReference
page
Rear fog lampRear fog lamp do not illuminate when the rear fog lamp switch
is turned on.N-154B-40
Rear fog lamp do not go out when the headlamps and front fog
lamps are turned off while the rear fog lamp is on.N-254B-40
Room lampRoom lamp does not illuminate.O-154B-41
Room lamp dimming function does not work normally.O-254B-41
Center displayCenter display does not work normally.–GROUP 54A
– Center Dis-
play.
DEFECTS FOUND BY INPUT SIGNAL CHECK
If the input signal check finds a defect, follow the table below to check.
Trouble symptomInspection
procedureReference
page
Ignition switch (ACC) signal is not sent to the ETACS-ECU.P-154B-42
Ignition switch (IG1) signal is not sent to the ETACS-ECU.P-254B-42
Key reminder switch signal is not sent to the ETACS-ECU.P-354B-43
Hazard warning lamp switch signal is not sent to the ETACS-ECU.P-454B-43
Front fog lamp switch signal is not sent to the ETACS-ECU.P-554B-44
Rear fog lamp switch signal is not sent to the ETACS-ECU.P-654B-45
Back-up lamp switch signal is not sent to the ETACS-ECU.
Inhibitor switch (reverse) signal is not sent to the ETACS-ECU.P-854B-46
Rear wiper motor auto-stop signal is not sent to the ETACS-ECU.P-954B-46
Driver’s door switch signal is not sent to the ETACS-ECU.P-1054B-47
Door switches signal is not sent to the ETACS-ECU.
Front passenger’s or back door lock key cylinder switch signal is not sent to the
ETACS-ECU.P-1154B-48
Driver’s door lock actuator switch signal is not sent to the ETACS-ECU.P-1254B-48
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1702 of 1839
SWS -Troubleshooting54B-16
Trouble symptomInspection
procedureReference
page
Column switchTail lamp switch signal is not sent to the ETACS-ECU.P-1354B-49
Headlamp switch signal is not sent to the ETACS-ECU.
Dimmer switch signal is not sent to the ETACS-ECU.
Passing switch signal is not sent to the ETACS-ECU.
Turn-signal lamp switch signal is not sent to the ETACS-ECU.
Windshield mist wiper switch signal is not sent to the
ETACS-ECU.P-1454B-50
Windshield intermittent wiper switch signal is not sent to the
ETACS-ECU.
Windshield low-speed wiper switch signal is not sent to the
ETACS-ECU.
Windshield high-speed wiper switch signal is not sent to the
ETACS-ECU.
Windshield intermittent wiper interval adjusting knob signal is
not sent to the ETACS-ECU.P-1554B-50
Windshield washer switch signal is not sent to the
ETACS-ECU.P-1454B-50
Rear wiper switch signal is not sent to the ETACS-ECU.
Rear washer switch signal is not sent to the ETACS-ECU.
Headlamp washer switch signal is not sent to the ETACS-ECU.P-1354B-49
Power window
main switchAny switch signal is not sent to the ETACS-ECU.P-1654B-51
TransmitterAny switch signal is not sent to the ETACS-ECU.P-1754B-52
Sunroof switchAny switch signal is not sent to the ETACS-ECU.P-1854B-52
Center displayAny switch signal is not sent to the ETACS-ECU.P-1954B-53
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1704 of 1839
SWS -Troubleshooting54B-18
Inspection Procedure B-2
Buzzer: Center display operation annunciation function
does not work normally.Probable cause
If the center display is operating normally, the cause is probably a malfunction in
the harness between the center display and the ETACS-ECU or in the
ETACS-ECU itself.DMalfunction of center display
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
Ye s
NG
Check the center display input circuit. (Refer to P.54B-53, Inspection
Procedure P-19.)
OK
Replace the ETACS-ECU.
MUT-
IIinput signal check
DCenter display
Is the center display operating normally?NoCarry out troubleshooting for the center display. (Refer to
GROUP 54A – Center Display.)
Inspection Procedure C-1
Central door locking system: Central door locking system
does not work normally.Probable cause
The power supply circuit, the circuit shared by door lock actuators, or the
ETACS-ECU may be defective.DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NG
NG
Repair
NG
Check the harness wire between ETACS-ECU and fusible link
(1).
OK
NG
Repair
NG
NG
Repair
OK
Replace the ETACS-ECU.
Check the harness wire between ETACS-ECU and door lock actua-
tor.
OK
Check trouble symptoms.
Check the following connectors:
D-224, D-209, D-218
Measure at ETACS-ECU connector D-223.
DDisconnect connector and measure at J/B side.
DVoltage between terminal 12 and body earth.
OK:System voltage
OK
Check trouble symptoms.
Check the following connectors:
D-224, D-211, D-27
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1739 of 1839
SWS -Troubleshooting54B-53
Inspection Procedure P-19
Center display: Any switch signal is not sent to the
ETACS-ECU.Probable cause
The cause is probably a malfunction of the center display or the ETACS-ECU.DMalfunction of center display
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector.
Ye s
NG
Repair
NG
Replace the ETACS-ECU.
OK
Replace the center display.Check trouble symptoms.
NG
Check the harness wire between center display and ETACS-ECU.NG
Repair
OK
Check trouble symptoms.
Check the following connectors:
D-06, D-31, D-226
Is the center display operated normally?NoCarry out troubleshooting for the center display. (Refer to
GROUP 54A – Center Display.)
Inspection Procedure Q-1
Check the circuit (power supply line) from the battery to
the ETACS-ECU.Probable cause
If that power supply circuit is defective, the circuit flowing through the ignition
switch (IG1) will function as a back-up circuit. In this case, the following
functions will not work when the ignition switch is at LOCK (OFF) position.
DIgnition key reminder warning buzzer function
DCentral door lock ing system
DIgnition key hole illumination lamp
DHazard warninglamp
DRoom lampDMalfunction of ETACS-ECU
DMalfunction of harness wire or connector.
NG
NG
Repair
NG
Check the harness wire between ETACS-ECU and fusible link
(2).
OK
Replace the ETACS-ECU.
OK
Check trouble symptoms.
Check the following connectors:
D-224, D-223, D-27Measure at ETACS-ECU connector D-224.
DDisconnect connector and measure at J/B side.
DVoltage between terminal 6 and body earth.
OK:System voltage
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk