ignition MITSUBISHI MONTERO 2000 Service Manual Online

MITSUBISHI MONTERO 2000 Service Manual Online MONTERO 2000 MITSUBISHI MITSUBISHI https://www.carmanualsonline.info/img/19/57331/w960_57331-0.png MITSUBISHI MONTERO 2000 Service Manual Online

Page 351 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>13A-137
Code No.14 Throttle position sensor (2nd channel)
systemProbable cause
The throttle valve controller judges a malfunction, and then transmit the result to
the engine-

Page 352 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>13A-138
OK
Measure at throttle valve controller
connector D-121.
DMeasure voltage at the throttle
valve controller connector
terminals.
DIgnition switch: ON
DVoltage between

Page 353 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>13A-139
OK
Check the harness wire between the
engine coolant temperaturesensor
and the engine-A/T-ECU.
MUT-
IIData list
21 Engine coolant temperature
sensor
OK:
When the engi

Page 354 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>13A-140
OK
Measure at engine coolant
temperature sensor connector B-56.
DUse test harness (MB991658) to
connect the connector, and
measure at the pick-up harness.
DIgnition s

Page 355 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>13A-141
OK
Check the harness wire between the
crankanglesensor and the
engine-A/T-ECU, and repair if
necessary.
MUT-
IIData list
22 Crankanglesensor (Refer to
P.13A-198, DATA

Page 357 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>13A-143
OK
Check the harness wire between the
intermediate connector and the
engine-A/T-ECU, and repair if
necessary.NG
Repair
NG
NG
Repair
NG
Repair
(2) NGMeasure at engine-

Page 359 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>13A-145
Code No.25 Barometric pressure sensor systemProbable cause
Range of Check
DTwo seconds have passed since the ignition switch is turned ON or the
engine startingproces

Page 360 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>GDI -Troubleshooting <A/T>13A-146
OK
Check the harness between the air
flow sensor and the engine-A/T-ECU,
and repair if necessary.
From the previouspage
OK
Measure at engine

Page 362 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>13A-148
OK
Use an analyzer to measure the
signal waveform at engine-A/T-ECU
connectors D-119 and D-120.
DEngine: Idling
DSelector lever position: P
DVoltage between terminal

Page 363 of 1839

MITSUBISHI MONTERO 2000  Service Manual Online GDI -Troubleshooting <A/T>13A-149
OK
Check trouble symptom.
OK
Check trouble symptom.
OK
Check the following connectors:
B-101, B-108, B-112,
B-113, B-116, B-119
NG
Repair
OK
Replace the engine-A/T-EC