sensor MITSUBISHI OUTLANDER 2014 3.G Rear Entertainment
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2014, Model line: OUTLANDER, Model: MITSUBISHI OUTLANDER 2014 3.GPages: 56, PDF Size: 9.69 MB
Page 5 of 56
7
Names and functions of parts
Names and functions of parts
OPEN
button
Buttons are on the main unit only.
· To open the display
→ P8
Display POWER
button
· Turning the power ON/OFF
→ P23
EJECT
button
This function is on the system panel only.
· To eject the disc
→ P24
POWER indicator
· Illuminates when the power is ON
→ P23
DISC indicator
· Illuminates when a disc is inserted
→ P24
Remote control sensor/infrared signal transmitter
· To receive remote control signals and transmit infrared wireless headphone signals. Disc loading slot
· To insert the disc.NOTE
·
Do not press in the
POWER
button and the
EJECT
button hard.
Names and functions of parts
mc4390mc4391
mc4392
Page 8 of 56
10Names and functions of parts
Names and functions of parts
Replacing the battery
Use your fi
ngernail to press tab A on
the battery case at the backside of the
remote control. While pressing tab A in
the direction shown in (1), pull the battery
case out as shown in (2)NOTE
· When disposing of the lithium battery, apply
insulating tape and dispose of the battery in
accordance with applicable local regulations. Place a new battery in the battery case
with its positive side facing up
New battery(positive side)
mc4380
Before using the remote controlThe remote control comes with a battery
installed.
There is an insulation sheet to prevent
the battery from discharging. Remove this
insulation sheet before using the remote
control.
mb073
Insulation sheet
Operating instructions
When using the remote control to operate
the system, aim the remote control at the
remote control sensor.
mc4394
Remote control sensorNOTE
· Do not disassemble or drop the remote control, and
do not subject the remote control to any physical
shock.
· Do not place any heavy objects on top of or sit on the remote control.
· If the remote control sensor is exposed to direct sunlight or other strong light, it may stop functioning
properly or stop operating at all. In this situation,
block out the light.
Page 10 of 56
12Names and functions of parts
Names and functions of parts
POWER button Press to turn the wireless headphone power ON/OFF.POWER indicator
Illuminates when the power is turned ON. (Red)Volume To adjust the volume.Infrared sensor To receive infrared signals from the system.
NOTE
· Do not press in the POWER
button hard.
· When the wireless headphones are ON but there is no audio or the audio signal cannot be received for more than three minutes, the wireless headphones
automatically go OFF.
· The wireless headphones can only receive audio signals in the rear seats (second
and third row seats).
· For safety’s sake, the driver must not use the
wireless headphones while driving. Doing so
could prevent the driver from hearing sounds
outside the vehicle and result in an accident.
· Adjust the wireless headphones volume to a
comfortable level. Listening at high volume for
an extended period may damage your hearing.
· Take off the wireless headphones and turn them
off when not in use.
CAUTION
Names and functions of wireless headphone parts
R
Volume
High
Low
mb029
R side
(right)
Page 50 of 56
Troubleshooting
52
Troubleshooting
Problem Cause Action to take
The wireless
headphones do not
work. The wireless
headphone power is
switched OFF, or the
volume is turned all
the way down.Check the wireless
headphone power and
volume.
The wireless
headphone battery is
run down. Replace the battery.
The disc does not
play. The disc is inserted
with the disc surface
facing up.Insert the disc with the
disc surface facing
down.
The disc is dirty or
scratched. Check the disc.
The inserted disc is
not supported by the
system.
The recording format
is not supported by
the system. Check the operation
of the recording
equipment.
Problem
Cause Action to take
The power does not
come on. The ignition key is in
the OFF position.Turn the ignition key
to the ACC or ON
positions.
The display remains
closed. Open the display or
press the POWER
button.
The remote control
does not work. The remote control
battery is run down.Replace the battery.
The system remote
control sensor is in
strong light, such as
direct sunlight. Avoid using the
system in direct
sunlight.
The remote control
is not aimed at the
system remote control
sensor. Aim the remote control
at the system remote
control sensor.
The screen is dark. The brightness is not properly adjusted.Make the necessary
adjustments.
The color is bad. The color or tint is not properly adjusted.