Display MITSUBISHI OUTLANDER SPORT 2014 3.G User Guide

Normal charging (charging method with rated AC 240 V outlet)
Charging 3-13
3
8. Make sure that the charging indicator (H)on the instrument cluster is illuminated.If the charging indicator is not illumi-nated, charging has not started.Make sure that the normal charge port andthe plug are correctly connected, and per-form charging from Step 5 again.
9. Charging is complete when the chargingindicator turns off. Pull out the normalcharge connector while pressing the but-ton (K).
10. Close the inner lid and press the rear of
the normal charging lid until it clicks toclose it.
11. Remove the charging cable plug from the
outlet.
IH
J
NOTE
zWhen the normal charge connector is con-nected to the charge port, the charging indi-cator will blink. When charging is started,the charging indicator is illuminated.zIf one of the doors is opened or the multi-information display switch is operated, thedrive battery level display (I) appears in themulti-information disp
lay and indicates the
drive battery level. In addition, when theremaining time is less than 1 hour, the pre-dicted charging time display (J) appears --:--and does not indicate a malfunction.
K
CAUTIONzBe sure to check the normal charge connec-tor is removed from the normal charge port.Since it will change into the state which canbe started the vehicle when the power switchis operated if the normal charge connectordoes not locked completely, resulting in anunexpected accident.NOTE
zCharging can be stopped half way. In thiscase, also, pull out the normal charge con-nector while pressing the button. Pressingthe manual stop button on the control boxcan also stop charging.Refer to “EV charging cable” on page 3-5.NOTE
zMake sure that the inner lid is completelyclosed.If the normal charging lid is forcibly closedwithout completely cl
osing inner lid, the
hinge on the inner lid may be broken.
BK0203201EN.book 13 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Charging troubleshooting guide
Charging 3-15
3
E08301501054
Charging troubleshooting guide
Symptom
Possible cause
Possible solution
Charging cannot be started.
The operation mode of the power switch in ON
Put the operation mode of the power switch in “OFF” before charging.
The drive battery is already fully charged.
Charging cannot be performed if the drive battery is already fully charged. Charging automatically turns off if the drive battery is fully charged.
The temperature of the drive battery is too high or too low to charge.
Confirm the drive battery temperature.Refer to “Cautions and actions to deal with intense heat” on page 2-8 and “Cautions and actions to deal with intense cold” on page 2-9.
The auxiliary battery is dis-charged.
The drive battery can not be charged if the vehicle electrical systems cannot be turned on. If the auxiliary battery is discharged, charge or emergency start the auxiliary battery. Refer to “Emergency starting” on page 9-2.
The vehicle or the charging cable has a malfunction.
The vehicle or charging cable may have a malfunction. Confirm if the warning lamp on the meter is illuminated. Confirm if the indicator on the control box is indicating a mal-function. If a warning is displayed, stop charging and contact a MITSUBISHI MOTORS Authorised Service Point.
BK0203201EN.book 15 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

MITSUBISHI Remote Control*3-18 Charging
3
zCustomize (function setting change)The function setting of the keyless opera-tion system, security alarm, outside rear-view mirror, operation mode of the powerswitch, air conditioning, lamps and wind-screen wipers can be changed by MIT-SUBISHI Remote Control.
Devices that support wireless LAN arerequired to communicate with the vehicleusing the MITSUBISHI Remote Control.Also, an SSID* (A) and password (B) arerequired to connect a wireless LAN device tothe vehicle. The SSID and password comewith the key at the time of your purchase ofthe vehicle.
NOTE
zThe electric heater is required to activate thereservation functions of
heater, defroster and
demister.zDue to the communication distance differsdepending on the wireless LAN device, thecommunication may down.
*: An SSID is the identifier of an access
point for IEEE 802.11 series wirelessLAN. It is displayed on wireless LANdevices.
For the operation method of the MITSUBI-SHI Remote Control, please visit Mitsubishi Motors’ Web site:http://www.mitsubishi-motors.com/en/prod-ucts/outlander_phev/app/remote/index.htmlzIf you need further information, please contact a MITSUBISHI MOTORS Authorized Service Point.
WA R N I N GzDo not use the MITSUBISHI RemoteControl if children, persons in need ofcare, pets, etc. are in the vehicle. Even ifthe remote climate control is used, thecabin may become hot or cold due to somereasons such as automatic stop of the sys-tem. The cabin temperature may quicklyrise in sunshine, which poses a risk of heatstroke and dehydration. In cold weather,on the other hand, the cabin temperaturemay quickly drop. Either of which couldlead to death in the worst case.zThe cooling fan in
the engine compart-
ment may operate automatically whencharging or when operating air condi-tioner. Do not bring you
r hand close to the
cooling fan during charging.CAUTIONzDo not use the timer charging or the remoteclimate control with a car cover.NOTE
zKeep the following points in mind whenusing a wireless LAN device:•Communication speed and range varydepending on the wirele
ss LAN devices and
the surrounding conditi
ons (radio environ-
ment, obstacles, parking area environment,etc.).
BK0203201EN.book 18 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless operation system
Locking and unlocking 4-11
4
E00305901715
In order to prevent vehicle theft or the accidental operation of
the keyless operation system, the buzzer and the display on th
e information screen
in the multi-information display are used to alert the driver.If a warning is activated, always check the vehicle and the keyless operation key. The warning is also displayed if there is a
fault in the keyless
operation system.
NOTE
zFunctions can be modified as stated below.For further information, please contact yourMITSUBISHI MOTORS Authorised ServicePoint.On vehicles equipped with Mitsubishi Multi-Communication System (MMCS), screenoperations can be used
to make the adjust-
ment. Refer to the se
parate owner’s manual
for details.
•Set the confirmation function (blinking ofthe turn-signal lamps) to operate only whenthe vehicle is locked or only when the vehi-cle is unlocked.•Disable the operation confirmation function(blinking of the turn-signal lamps).•Change the number of blinks for the opera-tion confirmation function (blinks of theturn-signal lamps).NOTE
Wa r n i n g a c t i v a t i o n
Item
Display
Buzzer
Note (Solution)
Detection of failure
Inner buzzer sounds once
There is a fault in the keyless operation system.
Fall of battery voltage
Inner buzzer sounds once
The battery starts to run out, the warning is activated.
（The warning is
not activated if the battery is completely dead.
）
BK0203201EN.book 11 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless operation system4-12 Locking and unlocking
4
Key not detected
Inner buzzer sounds once
When the engine switch is turned to the ACC or ON from OFF or when the engine is started, the warning is activated, if any of the following conditions is occurred.•••Carrying another keyless operation key with a different code, or the keyless operation key could be outside the operating range.The battery of the keyless operation key is dead.Communication is blocked by electric wave environment.
Keyless operation key reminder
Inner buzzer sounds about 1 minuteOuter buzzer sounds about 3 seconds inter-mittently
If the operation mode is in OFF and the driver’s door is opened with the keyless operation key in the key slot, a warning is issued and the outer buzzer sounds for about 3 seconds and the inner buzzer sounds for about 1 minute to remind you to remove the key. If the key removed from key slot, the buzzer is stopped.
Keyless operation key take-out monitoring system
Inner buzzer sounds onceOuter buzzer sounds intermittently
••••When the vehicle is parked with the operation mode in any mode other than OFF, if you close the door after opening any of the doors and taking the keyless operation key out of the vehicle, a warning is issued until the key is detected in the vehicle.If you take the keyless operation key out of the vehicle through a window without opening a door, the keyless operation key take-out monitoring system does not operate.It is possible to change the setting to make the keyless operation key take-out monitoring system operate if you take the keyless operation key out from the vehicle through a window without opening a door. For further information, please contact a MITSUBISHI MOTORS Authorised Service Point.Even if you have the keyless operation key within the engine start operating range, if the keyless operation key and vehicle ID codes cannot be matched, for example due to the ambient environment or electromagnetic conditions, the warning may be activated.
Item
Display
Buzzer
Note (Solution)
BK0203201EN.book 12 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless operation system
Locking and unlocking 4-13
4
E00306000019E00307201464
The emergency key is built into the keylessoperation key. If the keyless operation func-tion cannot be used, for example because the
keyless operation key battery has worn out orthe vehicle battery is flat, you can lock andunlock the driver’s door and start the enginewith the emergency key.To u s e t h e e m e r g e n c y k e y ( A ) , u n l o c k t h elock knob (B) and remove it from the keylessoperation key (C).Refer to “Doors” on page 4-14, or “If the key-less operation key is not operating properly”on page 7-13.
Key lock-in preven-tion system
Inner buzzer sounds onceOuter buzzer sounds about 3 seconds inter-mittently
••When the operation mode is in OFF, if you close all the doors and the tailgate with the keyless operation key left in the vehicle and you try to lock the doors and tailgate by pressing the driver’s or front passenger’s door lock/unlock switch, or the tailgate LOCK switch, a warning is issued and you cannot lock the doors and tailgate.Make sure you have the keyless operation key with you before lock-ing the doors. Even if you leave the keyless operation key inside the vehicle, it is possible that the doors will lock depending on the sur-rounding environment and wireless signal conditions.
Door ajar prevention system
Inner buzzer sounds onceOuter buzzer sounds about 3 seconds inter-mittently
When the operation mode in OFF, if you try to lock the doors and tail-gate by pressing the driver’s or front passenger’s door lock/unlock switch, or the tailgate LOCK switch with one of the doors or the tail-gate not completely closed, a warning is issued and you cannot lock the doors and tailgate.
Operation mode OFF reminder system
Inner buzzer sounds onceOuter buzzer sounds about 3 seconds inter-mittently
When the operation mode is in any mode other than OFF, if you close all the doors and the tailgate then try to lock the doors and tailgate by pressing the driver’s or front passenger’s door lock/unlock switch, or the tailgate LOCK switch, a warning is issued and you cannot lock the doors and tailgate.
Item
Display
Buzzer
Note (Solution)
To o p e r a t e w i t h
out using the
keyless operation function Emergency key
BK0203201EN.book 13 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Seat belts
Seat and seat belts 5-11
5
Hold the latch plate and push the button onthe buckle.
E00409801960
If the operation mode of the power switch isput in ON while a seat belt is not fastened, thewarning lamp comes on and the tone soundsfor about 6 seconds to remind the driver andthe front passenger to fasten the seat belt.If the vehicle is driven with the seat belt stillunfastened, the warning lamp will blink andthe tone will sound intermittently until theseat belt is fastened. At the same time, “FAS-TEN SEAT BELT” is displayed on the infor-mation screen in the multi informationdisplay for the driver.
NOTE
zThe seat belts in the rear seating outsidepositions are equipped with an automaticlocking retractor (ALR) mechanism.If you pull the seat belt fully out of theretractor, the retractor will switch to its ALRchild restraint installation mode and lock,thus preventing further movement.If this happens, you s
hould switch the retrac-
tor back to its emergency locking retractor(ELR) mode by taking off the seat belt andfully rewinding it. You should then wear theseat belt again.(Refer to “Installing a child restraint systemto a 3-point type seat belt (with emer-gency/automatic locking mechanism)” onpage 5-18.)
To u n f a s t e n
NOTE
zAs the belt retracts au
tomatically, keep the
latch plate held while retracting so that thebelt stows slowly. Failure to do this coulddamage the vehicle.
Seat belt reminder For the driverFor the front passenger
BK0203201EN.book 11 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Pregnant women restraint5-14 Seat and seat belts
5
E00405600077
E00405701323
The driver’s seat and front passenger’s seateach have a seat belt equipped with a pre-ten-sioner system and
force limiter system.
E00405802259
When the operation mode of the powerswitch is in ON, if there is a frontal impact ora side impact severe enough to injure theand/or front passenger, the pre-tensioner sys-tem will retract their respective seat beltsinstantaneously, thus maximizing the seatbelt’s effectiveness.
E00405900360
The same warning lamp/display is shared bythe SRS airbags and the pre-tensioner seatbelts.Refer to “SRS warning lamp/display” onpage 5-30 .
Pregnant women restraint
WA R N I N GzSeat belts work for everyone, includingpregnant women. Pregnant women shoulduse the available seat belts. This willreduce the likelihood of injury to both thewoman and the unborn child. The lap beltshould be worn across the thighs and assnug against the hips as possible, but notacross the waist. Consult your doctor ifyou have any addition
al questions or con-
cerns.
Seat belt pre-tensioner sys-tem and force limiter system Pre-tensioner system
WA R N I N GzTo o b t a i n t h e b e s t r e s u l t s f r o m y o u r p r e -tensioner seat belt, make sure you haveadjusted your seat correctly and wearyour seat belt properly.
CAUTIONzInstallation of audio e
quipment or repairs in
the vicinity of the pre-tensioner seat belts orfloor console must be
performed in line with
MITSUBISHI MOTORS
guidelines. It is
important to do so because the work couldaffect the pre-tensioner systems.zIf you need to scrap the vehicle, please con-sult a MITSUBISHI MOTORS AuthorisedService Point.It is important to do so because unexpectedactivation of the pre-tensioner seat beltscould cause injuries.NOTE
zThe pre-tensioner seat belts will be activatedif the vehicle suffers a severe impact, even ifthe seat belts are not worn.zThe pre-tensioner seat belts are designed towork only once. After the pre-tensioner seatbelts have been activated, we recommendyou have it replaced by a MITSUBISHIMOTORS Authorised Service Point.
SRS warning
BK0203201EN.book 14 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Supplemental restrain
t system (SRS)-airbag
5-30 Seat and seat belts
5
E00407802673
There is a supplemental restraint system(“SRS”) warning lamp on the instrumentpanel. The system checks itself every time theoperation mode of the power switch is put inON. The SRS warning lamp will come on forseveral seconds and then go out. This is nor-mal and means the system is working prop-erly.If there is a problem involving one or more ofthe SRS components, the warning lamp willcome on and stay on. At the same time, thewarning display will appear on the informa-tion screen in the mu
lti information display.
The SRS warning lamp/display is shared bythe SRS airbag and the seat belt pre-tensionersystem.
E00407901619
SRS warning lamp/display
WA R N I N GzIf any of the following conditions occur,there may be a problem with the SRS air-bags and/or seat belt
pre-tensioners, and
they may not function
properly in a colli-
sion or may suddenly
activate without a
collision:•Even when the operation mode is in ON,the SRS warning lamp does not come onor it remains on.• The SRS warning lamp and/or the warn-ing display comes on while driving.The SRS airbags and seat belt pre-ten-sioners are designed to help reduce therisk of serious injury
or death in certain
collisions. If either of the above conditionsoccurs, immediately
have your vehicle
checked by a MITSUBISHI MOTORSAuthorised Service Point.
SRS servicing
WA R N I N GzWe re commend any main tenanc e per-formed on or near the components of theSRS to be performed by a MITSUBISHIMOTORS Authorised Service Point.Improper work on the SRS components orwiring could result in inadvertent deploy-ment of the airbags,
or could render the
SRS inoperative; either situation couldresult in serious injury.
zDo not modify your steering wheel, seatbelt retractor or any other SRS compo-nents. For example, replacement of thesteering wheel, or modifications to thefront bumper or body structure (forexample fitment of a frontal protectionbar, including roo bars and bull barsexcept approved MITSUBISHI MOTORSGENUINE accessory parts) can adverselyaffect SRS performance and lead to possi-ble injury.zIf your vehicle has received any damage,we recommend you to have the SRSinspected to ensure it is in proper workingorder.zDo not modify your front seats, centre pil-lar and centre console.It can adversely affect SRS performanceand lead to possible injury.zIf you found any tear, scratch, crack ordamage to the portion where the airbag isstored, you should h
ave the SRS inspected
by a MITSUBISHI MOTORS AuthorisedService Point.NOTE
zIf your vehicle has to be scrapped, do this inline with local legislation and contact a MIT-SUBISHI MOTORS Authorised ServicePoint to safely dismantle the airbag system.WA R N I N G
BK0203201EN.book 30 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

6
Instruments and controlsInstruments .......................................................................................6-2Multi information display ................................................................. 6-3Indicator lamp, warning lamp, and information screen display list.....................................................................................................6-21Indicator lamps ...............................................................................6-36Wa r n i n g l a m p s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 3 7Information screen display .............................................................6-39Combination headlamps and dipper switch ....................................6-40Headlamp levelling .........................................................................6-44Turn-signal lever ............................................................................. 6-45Hazard warning flasher switch .......................................................6-45ECO mode switch ..........................................................................6-46Fog lamp switch .............................................................................6-46Wi p er and w ashe r sw it ch .. . . .. . .. . . .. . . .. . .. . . .. . . .. . .. . . .. . .. . . .. . . .. . .. . . .. . . .. . .. . . . 6- 4 7Wi p er dei ce r sw it ch * .. . .. . . .. . . .. . .. . . .. . . .. . .. . . .. . . .. . .. . . .. . .. . . .. . . .. . .. . . .. . . .. . .. . . . 6- 5 3Rear window demister switch.........................................................6-53Horn switch.....................................................................................6-54
BK0203201EN.book 1 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分