fog light MITSUBISHI OUTLANDER SPORT 2014 3.G Owners Manual

Combination headlamps and dipper switch
Instruments and controls 6-41
6
Rotate the switch to turn on the lamps.
Rotate the switch to turn on the lamps.
zWhen it rains, or when the vehicle has beenwashed, the inside of the lens sometimesbecomes foggy, but this does not indicate afunctional problem.When the lamp is swit
ched on, the heat will
remove the fog. However, if water gathersinside the lamp, we recommend you to havechecked.
Ty p e 1 OFF All lamps off
Position, tail, licence plate, instru-ment panel lamps and downlight onHeadlamps and other lamps go onNOTE
Ty p e 2 OFF All lamps offAUTO
With the operation mode of the power switch is in ON, head-lamps, position, tail, licence plate, instrument panel lamps and down-light turn on and off automatically in accordance with outside light level. All lamps turn off automati-cally when the operation mode is put in OFF.

Position, tail, licence plate, instru-ment panel lamps and downlight onHeadlamps and other lamps go on
NOTE
zThe sensitivity of the automatic on/off con-trol can be adjusted. For further information,contact a MITSUBISHI MOTORS Author-ised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment.Refer to the separate owner’s manual fordetails.zIf the front fog lamps turn on when they aresupposed to with the
switch in the “AUTO”
position, the lamps turn off automaticallywith operation mode off.zDo not cover the sensor (A) for the automaticon/off control by affixing a sticker or label tothe windscreen.zIf the lamps do not turn on or off with theswitch in the “AUTO”
position, manually
operate the switch and we recommend you tohave your vehicle checked.
BK0203201EN.book 41 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Combination headlamps and dipper switch6-42 Instruments and controls
6
zIf the operation mode of the power switchis put in OFF or ACC while the lampswitch is in the “ ” or “ ” position,the lamps will turn off automaticallywhen the driver"s door is opened.zIf the operation mode of the power switchis put in OFF or ACC while the lampswitch is in the “ ” or “ ” position,the lamps will remain on for about 3 min-utes while the driver’s door is shut andwill then automatically turn off.
1. Turn the lamp switch in the “OFF” posi-tion while the operation mode of thepower switch is in OFF or ACC.2. Turn on the lamps with the switch in the“ ” or “ ” position again, then thelamps will remain on.3. When 1 minute has passed, the lamps willautomatically be turned off.
E00506101631
If the driver’s door is opened when the opera-tion mode of the power switch is put in ACCor OFF with the lamps illuminated, a buzzerwill sound to remind the driver to turn off thelamps.The buzzer will automatically stop if theauto-cutoff function is activated, the lampswitch is turned off, or the door is closed.
E00506201544
When the lamp switch is in the “ ” posi-tion, the beam changes from high to low (orlow to high) each time the lever is pulledfully (1). While the high beam is on, the highbeam indicator lamp in the instrument clusterwill also illuminate.
E00506300199
The high beams flash when the lever is pulledslightly (2), and will go off when it isreleased.When the high beam is on, the high beamindicator lamp in the instrument cluster willilluminate.
Lamps (headlamps, fog lamp, etc.) auto-cutout function
NOTE
zThe lamp auto-cutout function can also bedisabled.For further information, we recommend youto consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.
When you want to keep the lamps on:
NOTE
zIf you place the light switch in the “ ”position, the lamps will not be automaticallyturned off.
Lamp monitor buzzer
Dipper (High/Low beam change) Headlamp flasher
BK0203201EN.book 42 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Horn switch6-54 Instruments and controls
6
E00508000640
Press the steering wheel on or around the“ ”mark.
zSince the demister requires a significantamount of power, stop the demister as soonas the window is demi
sted. Using it for a
long time may reduce the auxiliary batteryvoltage, making it impossible to start thePlug-in Hybrid EV System.zOn vehicles equipped with heated mirrors,when the rear window demister switch ispressed, the outside rear-view mirrors aredefogged or defrosted. Refer to “Heated mir-ror” on page 7-9.zOn vehicles equipped with the wiper deicer,when the rear window demister switch ispushed, the window glass becomes warmand the wipers become operable. Refer to“Wiper deicer switch” on page 6-53.NOTE
zIt is possible to cha
nge the setting to make
the rear window demister operate automati-cally when ambient
temperature becomes
low while the ready indicator lamp is illumi-nated, even if you do not push the rear win-dow demister switch.It operates automatica
lly only once after put-
ting the operation mode in ON.If you choose this setting, the heated mirrors(if so equipped) and
wiper deicer (if so
equipped) will also operate automatically atthe same time.For further informati
on, we recommend you
to consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the se
parate owner’s manual
for details.zThe demister switch is
not to melt snow but
to clear mist. Remove snow before use of thedemister switch.zWhen cleaning the inside of the rear window,use a soft cloth and
wipe lightly along the
heater wires, being careful not to damage thewires.zDo not allow objects to
touch the inside of
the rear window glass,
damaged or broken
wires may result.NOTE
Horn switch
BK0203201EN.book 54 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Lane Departure Warning (LDW)*7-62 Starting and driving
7
E00635901023
If a problem occurs with the system, a visualwarning specific to the type of the problem isgiven together with an audible alarm.The alarm shown below is displayed if thesystem becomes temporarily unable due totoo high a temperature of the LDW camera.If the camera cools down below the predeter-mined temperature, the system automaticallyrecovers the normal state.
The alarm shown below is displayed if LDWbecomes to a non-initialized state due to afault.If this happens, please contact a MITSUBI-SHI MOTORS Authorised Service Point forinspection of the system.
NOTE
zIf warning continues
for about 10 seconds or
more, the system switches to the standbymode before the warning stops.
System problem warning

To o h o t L D W c a m e r a

NOTE
zThe warning message can be cleared tempo-rarily by setting the LDW switch to “OFF.”
LDW deactivation due to fault

CAUTIONzLDW has its performance limitations. Do notover-rely on the system.zLDW is not designed to
lessen risks associ-
ated with not looking ah
ead carefully (atten-
tion drawn to something on the side,absentmindedness, etc.) or poor visibilitycaused by bad weather etc. Keep steeringyour vehicle correctly and drive safely.
zThe system may not be able to detect the lanecorrectly in the following conditions. Ifrequired, set the LDW switch to “OFF.”•When driving on a road whose lane mark-ings (white or yellow) are worn out orsmeared with dirt to an extent not recogniz-able by the system.•When lane markings are vague, typicallyduring a drive in the rain, snow or fog, orwhen running against the sun.•When the vehicle is moving in a placewhere lane markings are interrupted, suchas a toll booth entrance and motorway junc-tion.•When running on a road portion withincompletely removed old lane markings,shadows, lingering snow, truck-like puddlesmistakable for lane markings (especiallyafter the rain when road surface is reflect-ing light) or simila
r confusing factors.
•When running in a lane other than the cruis-ing lane and
passing lane.
•When running beside a closed lane sectionor in a provisional lane in a traffic workzone.•When running in an extremely narrow lane.•When the following distance between yourvehicle and a vehicle in front becomesextremely reduced (especially when amarking is hidden by a vehicle in front thisis running too close to the marking).•When entering a juncti
on or other point of
road where lanes are laid out complicatedly.CAUTION
BK0203201EN.book 62 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Fuses11-18 Maintenance
11
*: Fusible linkzSome fuses may not be installed on yourvehicle, depending on the vehicle modelor specifications.
zThe table above shows the main equip-ment corresponding to each fuse.
E01008001867
16
SRS airbag 7.5 A
17
Radio 15 A
18
Control unit
relay
7.5 A
19
Interior lamps(Room lamps)
15 A
20
Reversing lamps
(Backup lamps)
7.5 A
21
Heated door
mirror
7.5 A
22
Outside rear-view mirrors
10 A
23
Cigarette lighter/Accessory socket
15 A
24
Charge 7.5 A
25
Power seat 30 A
*
26
Heated seat 30 A
No.
Symbol
Electrical sys-
tem
Capacity
Engine compartment fuse location table Behind of the fuse block coverMain fuse block
No.
Sym-bol
Electrical sys-
tem
Capacities
SBF1
Air condition-ing condenser fan motor
30 A
*
SBF2 — — —SBF3 — — —SBF4
Radiator fan
motor
40 A
*
SBF5
Anti-lock brak-ing system
40 A
*
SBF6 — — —SBF7
Anti-lock brak-ing system
30 A
*
BF1
Electric tailgate 30 A
BF2
Audio system
amp
30 A
BF3 IOD IOD 30 ABF4 — — —F1 — — —F2
Wiper deicer 15A
F3 — — —F4
Daytime run-ning lamps
10 A
F5
Front fog lamps 15 A
F6 — — —
BK0203201EN.book 18 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分