wiper blades MITSUBISHI OUTLANDER SPORT 2014 3.G Owners Manual

Wiper and washer switch
Instruments and controls 6-47
6
E00508401612
The rear fog lamp can be operated when theheadlamps or front fog lamps turn on.An indicator lamp in the instrument clustercomes on when the rear fog lamp is turnedon.
Turn the knob once in the “ON” direction toturn on the front fog lamps. Turn the knobonce more in the “ON” direction to turn onthe rear fog lamp. To turn the rear fog lampoff, turn the knob once in the “OFF” direc-tion. Turn the knob once more in the “OFF”direction to turn off the front fog lamps. Theknob will automatically return to its originalposition when you release it.
E00507101218E00516901687
The windscreen wipers can be operated withthe operation mode of the power switch inON or ACC.If the blades are frozen to the windscreen orrear window, do not operate the wipers until
NOTE
zThe front fog lamps are automatically turnedoff when the headlamps or tail lamps areturned off. To turn the front fog lamps onagain, turn the knob in
the “ON” direction
after turning on the headlamps or tail lamps.zDo not use fog lamps except in conditions offog, otherwise excessi
ve lamp glare may
temporarily blind oncoming vehicle drivers.
Rear fog lamp switch
*
RHD (Type 2)
NOTE
zThe rear fog lamp is automatically turned offwhen the headlamps or front fog lamps areturned off.zTo t u r n t h e r e a r f o g l a m p o n a g a i n , t u r n t h eknob twice in the “ON” direction after turn-ing on the headlamps.
Wiper and washer switch
CAUTIONzIf the washer is used in cold weather, thewasher fluid sprayed against the glass mayfreeze, which may hinder visibility. Warmthe glass with the de
froster or rear window
demister before using the washer.
Windscreen wipers
NOTE
zTo e n s u r e a c l e a r r e a r w a r d v i e w, t h e r e a rwindow wiper will automatically performseveral continuous
operations if the selector
lever is put in the “R” position while thewindscreen wipers are operating. Refer to “Rear window wiper and washer”on page 6-51.
Except for vehicles equipped with rain sensor
BK0203201EN.book 47 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Wiper and washer switch6-48 Instruments and controls
6
the ice has melted and the blades are freed,otherwise the wiper motor may be damaged.With the lever in the “INT” (speed-sensitive)position, the intermittent intervals can beadjusted by turning the knob (A).
The misting function can be operated with theoperation mode of the power switch in ON orACC.
The wipers will operate once if the wiperlever is raised to the “MIST” position andreleased. This operation is useful when it isdrizzling, etc. The wipers will continue tooperate while the lever is held in the “MIST”position.
E00517001409
The windscreen wipers can be operated withthe operation mode of the power switch inON or ACC.If the blades are frozen to the windscreen orrear window, do not operate the wipers untilthe ice has melted and the blades are freed,otherwise the wiper motor may be damaged.
MIST- Misting function
The wipers will operate once.
OFF- OffINT- Intermittent (Speed sensitive)LO- SlowHI- FastTo a d j u s t i n t e r m i t t e n t i n t e r v a l s
1- Fast2- Slow
NOTE
zThe speed-sensitive-operation function ofthe windscreen wipers can be deactivated.For further informati
on, we recommend you
to consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the se
parate owner’s manual
for details.
Misting function
Ve h i c l e s e q u i p p e d w i t h r a i n s e n s o r
BK0203201EN.book 48 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Wiper deicer switch*
Instruments and controls 6-53
6
E00507601167
zIf the moving wipers become blocked byice or other deposits on the glass, themotor may burn out even if the wiperswitch is turned to OFF. If obstructionoccurs, park your vehicle in a safe place,stop the Plug-in Hybrid EV System, andclean the deposits from the glass so thatthe wipers operate smoothly.zDo not use the wipers when the glass isdry.They may scratch the glass surface andthe blades wear out prematurely.zBefore using the wipers in cold weather,check that the wiper blades are not frozenonto the glass. The motor may burn out ifthe wipers are used with the blades frozenonto the glass.zAv o i d u s i n g t h e w a s h e r c o n t i n u o u s l y f o rmore than 20 seconds. Do not operate thewasher when the fluid reservoir is empty.Otherwise, the motor may burn out.
zPeriodically check the level of washerfluid in the reservoir and refill if required.During cold weather, add a recommendedwasher solution that will not freeze in thewasher reservoir. Failure to do so couldresult in loss of washer function and frostdamage to the system components.
E00507701142
The rear window demister switch can beoperated when the Plug-in Hybrid EV Systemis operating.When the front wipers have frozen to thewindscreen at the parked positions, turningon this switch will heat the windscreen tomake the wipers operable. Press the rear win-dow demister switch and the deicer will oper-ate.
E00507902284
The rear window demister switch can beoperated when the operation mode of thepower switch is in ON.Push the switch to turn on the rear windowdemister. It will be turned off automatically inabout 15 to 20 minutes depending on the out-side temperature. To turn off the demisterwhile it is operating, push the switch again.The indicator lamp (A) will illuminate whilethe demister is on.
NOTE
zIf the operation mode is in ON or ACC andthe headlamps are on,
the headlamp washer
operates together with the windscreenwasher the first time the windscreen washerlever is pulled.
Precautions to observe when using wipers and washers
Wiper deicer switch*
NOTE
zThe wiper deicer is activated/deactivated,depending on the operation of the rear win-dow demister. Refer to “Rear windowdemister switch” on page 6-53.
Rear window demister switch
NOTE
zDo not use this switch when the ready indi-cator lamp is not illuminated. The auxiliarybattery could go flat, making it impossible tostart the Plug-in Hybrid EV System.
BK0203201EN.book 53 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Cleaning the exterior of your vehicle10-6 Vehicle care
10
E00901500347
1. Remove dirt using a sponge while sprin-kling water on the vehicle.2. Use neutral detergent on any dirt that can-not be removed easily with water.Rinse off the neutral detergent after wash-ing the vehicle.3. Dry the vehicle thoroughly using a cham-ois leather or a soft cloth.
E00901600117
The window glass can normally be cleanedusing only a sponge and water.Glass cleaner can be used to remove oil,grease, insect carcasses, etc. After washing
the glass, wipe it dry with a clean, dry, softcloth. Never use a cloth that is used for clean-ing a painted surface to clean a window. Waxfrom the painted surface could get on theglass and lower glass transparency and visi-bility.
E00901700062
Use a soft cloth and glass cleaner to removegrease, dead insects, etc., from the wiperblades. Replace the wiper blades when theyno longer wipe properly. (Refer to page11-12.)
E00902200051
Use a soft cloth to clean the inner side of thesunroof. Hard deposits should be wiped awaywith a cloth dipped in warm, neutral deter-gent solution. Wipe away the solution with asponge dipped in fresh water.
E00902100483
Clean the engine compartment at the begin-ning of autumn and end of winter. Pay partic-ular attention to flanges, crevices andperipheral parts where dust containing roadchemicals and other corrosive materialsmight collect.If salt and other chemicals are used on theroads in your area, or you live within 20 kmof the sea, clean the engine compartment atleast every three months.Never spray or splash water on the electricalcomponents in the engine compartment, asthis may cause damage.Do not bring the nearby parts, the plasticparts and so on into contact with sulphuricacid (battery electrolyte) which may crack,stain or discolour them.If they are in contact, wipe off with soft cloth,chamois or the like and an aqueous solutionof neutral detergent then immediately rinsethe affected parts with plenty of water.
Aluminium wheels*
CAUTIONzDo not use a brush or other hard implementon the wheels.Doing so could scratch the wheels.zDo not use any cleaner th
at contains an abra-
sive substance or is aci
dic or alkaline. Doing
so could cause the coating on the wheels topeel or become discoloured or stained.zDo not directly apply
hot water using a steam
cleaner or by any other means.zContact with seawater and road deicer cancause corrosion. Rinse off such substances assoon as possible.
Window glass
NOTE
zTo c l e a n t h e i n s i d e o f t h e r e a r w i n d o w,always use a soft cloth and wipe the windowglass along the demister heater element so asnot to cause damage.
Wiper blades Cleaning the sunroof*
NOTE
zThe surface treatment on the inside of theglass may be removed if hard cloth ororganic solvent (benzi
ne, kerosene, thinner,
etc.) is used.
Engine compartment
BK0203201EN.book 6 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Wiper blade rubber replacement11-12 Maintenance
11
E01002101882
It is recommended that snow chains are car-ried in snow regions and fitted when requiredto the front wheels in accardance with themanufacture’s instructions.On 4WD vehicles in which the driving poweris distributed preferentially to the frontwheels, ensure that the tyre chains are fittedon the front.The tyres fitted to your vehicle as originalequipment allow you to fit tyre chains if theyare required. When replacing your tyres,check with the tyre distributor or manufac-turer if the fitting of tyre chains will be detri-mental to the tyres being purchased.
Always follow the chain manufacturer’sinstructions when fitting the chains.
E01002600532
1. Lift the wiper arm off the windscreen.
CAUTIONzObserve permissible maximum speed foryour snow tyres and the legal speed limit.NOTE
zThe laws and regula
tions concerning snow
tyres (driving speed, requi
red use, type, etc.)
vary. Find out and follow the laws and regu-lations in the area you intend to drive.zIf flange nuts are used on your vehicle,change to tapered nuts when steel wheels areused.
Ty r e c h a i n s
WA R N I N GzDO NOT use a jack when fitting thechains, as in the conditions, the tyres mayslip on the ic
y road causing the vehicle to
slip off the jack.CAUTIONzChoose a clear straight stretch of road whereyou can pull off and still be seen while youare fitting the chains.zDo not fit chains before you need them. Thiswill wear out your tyres and the road surface.zAfter driving around 100-300 metres, stopand retighten the chains.zCare should be taken with extremes of steer-ing lock to prevent possible contact betweenthe chains and the vehicle body.zDrive carefully and do not exceed 30 km/h.Remember, fitting chains is not going to stopaccidents from happening.zWhen tyre chains are installed, take care thatthey do not damage the disc wheel or body.zAn aluminium wheel can be damaged by atyre chain while driving. When fitting a tyrechain on an aluminium wheel, take care thatany part of the chai
n and fitting cannot be
brought into contact with the wheel.
zRemove the wheel covers before installing atyre chain, otherwise they may be damagedby the tyre chain. (Refer to page 9-18.)zWhen installing or removing the tyre chains,take care that hands and other parts of yourbody are not injured by the sharp edges ofthe vehicle body.zInstall the chains only on the front tyres andtighten them as tightly
as possible with the
ends securely fastened.
Wiper blade rubber replace-ment Windscreen wiper blades
CAUTION
BK0203201EN.book 12 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Wiper blade rubber replacement
Maintenance 11-13
11
2. Pull the wiper blade until its stopper (A)disengages from the hook (B). Then, pullthe wiper blade further to remove it.
3. Attach the retainers (C) to a new wiperblade.Refer to the illustration to ensure that theretainers are correctly aligned as youattach them.4. Insert the wiper blade into the arm, start-ing with the opposite end of the bladefrom the stopper. Make sure the hook (B)is fitted correctly in the grooves in theblade.
5. Push the wiper blade until the hook (B)engages securely with the stopper (A).1. Lift the wiper arm off the window glass.2. Pull the wiper blade downward to disen-gage it from the stopper (A) at the end ofthe wiper arm. Pull the wiper blade fur-ther to remove it.
NOTE
zDo not allow the wiper arm to fall onto thewindscreen; it coul
d damage the glass.
NOTE
zIf retainers are not supplied with the newwiper blade, use the retainers from the oldblade.
Rear window wiper blades
BK0203201EN.book 13 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Alphabetical index
13-5
13
Stopping the Plug-in Hybrid EV System 7-12Storage spaces
....................................
8-68
Sun visors
..........................................
8-64
Sunroof
..............................................
4-31
Supplemental restraint system
..............
5-21
Servicing
.......................................
5-30
System check screen
...........................
6-12
T
Tail lamps
Bulb capacity
...............................
11-22
Replacement
................................
11-27
Tailgate
..............................................
4-16
Taking your vehicle overseas
...............
2-16
Tank capacity
.....................................
2-13
Time Setting
.......................................
8-36
Tools
...................................................
9-7
Storage
............................................
9-6
Towing
..............................................
9-19
Towing caravans and trailers
................
7-71
Transfer oil
......................................
12-10
Turn/Lane-change signals
....................
6-45
Turn-signal indicator lamps
.................
6-36
Tyre repair kit
.......................................
9-7
Tyres
.................................................
11-9
How to change a tyre
......................
9-14
Inflation pressures
.........................
11-10
Rotation
.......................................
11-11
Size (tyre and wheel)
......................
12-8
Snow tyres
....................................
11-11
Tread wear indicators
....................
11-10
Tyre chains
...................................
11-12
Tyre repair kit
..................................
9-7
U
USB input terminal
.............................
8-61
How to connect a USB memory
.......
8-61
How to connect an iPod
..................
8-62
V
Vanity mirror lamp
Bulb capacity
................................
11-23
Vehcile data label
...............................
12-2
Vehicle care precautions
.....................
10-2
Vehicle dimensions
............................
12-4
Vehicle identification number
..............
12-2
Vehicle information code plate
............
12-2
Vehicle labeling
.................................
12-2
Vehicle mass
......................................
12-5
Vehicle performance
...........................
12-5
Ventilators
...........................................
8-2
W
Warning lamps
...................................
6-37
Washer
Fluid
...................................
11-7
, 12-10
Switch
...........................................
6-51
Washing
.............................................
10-3
Waxing
..............................................
10-5
Wheel
Covers
...........................................
9-18
Specification
..................................
12-8
Wiper
Rear window
..................................
6-51
Windscreen
....................................
6-47
Wiper blades
................................
11-12
Wiper deicer switch
............................
6-53
BK0203201EN.book 5 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分