ECU NISSAN 300ZX 1984 Z31 Body Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 1984, Model line: 300ZX, Model: NISSAN 300ZX 1984 Z31Pages: 77, PDF Size: 1.97 MB
Page 6 of 77
BODYENDANDDOOR
When removing and installing hood or back door, place a cloth or other padding on hood or back door
corners to avoid scratching vehicle body
When removing clip or fastener,
refer to CLIP & FASTENER.
Apply sealing compound where necessary when installing parts
Front End
Hood adjustment Adjust at hinge portion
Hood lock adjustment After adjusting, check hood lock control operation Apply a coat of grease to
hood locks engaging mechanism
Hood opener
Do not attempt to bend cable forcibly. Doing so increases effort required to unlock hood.
Bumper fascia.
It is made of plastic, so do not use excessive force and take care to keep oil away from it
When adjusting or removing/installing hood or removing/installing hood switch, check theft warning sys-
tem operation
WARNING:
a. Be careful not to scratch hood stay when installing hood. A scratched stay may cause gas leakage.
b. The contents
of the hood stay are under pressure. Do not take apart, puncture, apply heat or allow fire
near It.
Bumper shock absorber inspection
1. Check shock absorber for oil leakage, cracks or deformation
2. Function of shock absorber,
(1) Place vehicle in front of a wall
(2) Place a jack between bumper and wall, jack is positioned squarely with bumper directly in line with
(3) Apply pressure to compress shock absorber at least 10.0 mm (0.394 in).
Use a jack with capacity of more than 600 kg (1,323 Ib).
(4) Make sure bumper returns to its original position when jack is retracted Replace if necessary
CAUTION:
It IS not recommended to confirm proper installation by driving into walls or other barriers as this could
cause personal injury
or damage to the vehicle.
When replacing shock absorbers, make sure they
are of the same type and rating, and manufactured by the
same maker
Apply parking brake and place tire stoppers securely.
shock absorber
to be checked
BF-6
Page 42 of 77
BODYENDANDDOOR
Theft Warning System (Cont'd)
CONTROLLER INSPECTION
This inspection is available only when the cause of trouble in "Troubleshooting" is due to a "faulty sub-
control
AMP" or "faulty main control AMP". Therefore, the entire system needs to be inspected in
advance, according to the "Trouble-shooting procedures"
This inspection should be carried out with the adapter harness disconnected
at the main control AMP
When disconnecting the adapter harness, first disconnect the battery ground cable Be sure to reconnect
battery ground cable afterwards
@I through 0 indicate the respective terminals of the adapter harness connector at the main control
AMP.
This inspection
is based on the premise that the adapter harness is free from abnormalities Therefore,
the adapter harness must be inspected before inspecting the controller
Trouble diagnosis
b Symbols: 0: Execute, X: Not required, H. Approx 12V, L. Lessthan 1V.
Carry out the terminal inspection in this diagnosis chart from left to right.
The term "door" indicates the driver door, assist door, back door, and hood, unless otherwise speci-
fied.
The term "alarm" means that the horn sounds intermittently and the headlamps blink.
BF-42
Page 49 of 77
INSTRUMENT
These parts are made of plastlc, so do not use excessive force and be careful not to damage them
Remove griller by raising pawls umg flatbladed
screwdrwer
Removal. Instrument mmbinatlon wttch instrument comblnatlon [When removtng combination mfner. rwltch
First remove nut securing instrument comblnatlon swltch
basement, then remove lnitrurnent combmatlon swltch
(Instrument combmation witches are secured at hooks and basements 1
BF-49
Page 61 of 77
TRIM AND MOLDING
Exterioi
@ Sill molding
Front and rear ends of molding are fixed with double-faced
.When affixing the portion, heat body panel and moldlng
to adhesive tape
30 to 40'C I86 to 104'FI with a heat gun, and then innall gt
8 Drip molding
Body panel
SBF400B
0 Windshield upper & side molding
Molding fastener
(Set It when windshield glass IS installed I
Double-faced
adherive tape
[When
in-
tener, heat
body Panel
and fastener Otalllng far-
SBF401B
:ont'd)
@ Windshield lower molding
SBF402B
@ Side window molding
Refer to Side Window
@ Back door weatherstrip
Attach the weatherstrip by aligning each white
marking with the center of each back door
hinge
rsodv panel
Weatherstrip
When mstalltng.
carefully avoid
rolling and
-1 LAttach securely
Trim
SBF403B
0 Rear panel outer finisher
(Fwed wth double faced adhesive tape) SBF404B
BF-61